Do-it-yourself roller shutter repair

In detail: do-it-yourself roller shutter repair from a real master for the site my.housecope.com.

In order to increase the service life of the roller shutter, it is recommended to periodically inspect the moving parts, namely silicone inserts, bearings, etc., which are the first to wear out.

There are the following popular malfunctions of roller shutters:

shaft grinding - most likely, the bearing is worn out,
scuffs are observed on the canvas on both sides - the silicone inserts are worn out,
in the lower part, the canvas is skewed - the guides are clogged with garbage, mainly in the lower part.

When repairing roller shutters, you can encounter two types of malfunctions - minor, when you need to replace a small part, and serious, when you need to dismantle the structure and carry out a comprehensive repair. If in the first case you can do it yourself, then in the second case we recommend contacting roller shutter repair specialists. On the company's website, you can find a lot of useful information on the repair of roller shutters, as well as the contacts of the master in case you cannot solve the problem yourself.

If the bearing is defective, the following steps must be taken:

Buy a new bearing,
Lower the canvas to the lower position,
Remove the protective cover and shaft,
Dismantle the sliding plate,
Changing the bearing
We collect the rollet back.

If the roller shutter blade is not assembled evenly at the bottom, do the following:

Check guides for foreign objects
Check for mechanical resistance,
Remove foreign objects and recheck the mechanism.

The most common problems with automatic roller shutters:

The canvas does not rise
The canvas does not fall.

Can I fix these problems myself? Yes, you can, if you approach this issue carefully.

If in the case of raising or lowering the roller shutter, the canvas practically does not move, while minor movements are accompanied by noise and crunch. Perhaps this is a broken crossbar.

Video (click to play).

To fix this problem yourself, do the following:

Remove the protective cover
Check the bolt for integrity,
If the bolts are broken, they must be removed,
Install new ones.

If scuffs and noise are observed on the canvas along the entire length, then, most likely, the sealing tape has failed and frayed.

To fix the problem yourself, follow these steps:

Remove the protective cover
Let's drop the roller
We loosen the fastening in the side cover attached to the wall,
Raise the canvas
Unscrew the guide and remove it carefully,
Insert the seal.

As a rule, it is usually necessary to carry out repair of rolling shutters at the most inopportune moment. However, this should not be delayed, since a minor malfunction can lead to very serious and costly consequences. If you notice even slight changes in the operation of your design, then you need to immediately seek help. If you have previously serviced the canvas yourself, then do not put off the inspection indefinitely.

Each mechanism is designed for a certain period of operation. And this does not mean that you can safely use the design. Roller shutters should be serviced periodically to detect problems at an early stage. Timely maintenance is also necessary in order to timely replace worn parts. After all, there are rollers and silicone seals that wear out faster.

Serious damage can occur if the canvas has been operated with an increased load.Then its service life is simply reduced. But even in this case, it will be possible to repair the roller shutters. The main thing is not to continue operation if you hear extraneous noise during operation.

Extraneous influences and atmospheric phenomena (temperature changes, severe frosts) can also lead to a malfunction of the device. Self-repair of roller shutters is undesirable in this case, since specialists will better diagnose the causes of the problem and fix them faster.

All faults can be figuratively divided into several groups:

breakdown of the electric motor;
web blocking;
the bolt lock failed;
box damage.

The failure of the electric motor is the main failure of the roller shutters. This may be due to problems with the power cable, control panel or switch. Less commonly, the engine itself or its temperature sensor fails. In this case, most often it will be necessary to replace the broken element.

If you returned home, and the roller shutters do not open, then in this case it is necessary to call the masters as soon as possible. Do not try again and again to open it on your own. A specialist on site will be able to quickly figure out what caused the blockage. Most often this is due to faulty guides. A stop of movement also occurs if the canvas is deformed: the lamellas diverge, get stuck in the box. The cause may also be a broken cable or springs.

A high-quality crossbar lock cannot fail due to a technical malfunction. Most often, its breakdown will be caused by clogging or ingestion of a foreign object. The cause of a serious breakdown, due to which the roller shutters do not rise, may be damage to the protective box. This happens after a heavy object falls on it or the box elements fail.

Not every type of repair will be within the power of a simple man in the street. Most often, a call to the master is necessary so that he at least diagnoses the cause of the breakdown. But there are times when you can do the repair work on roller shutters with your own hands. Very often in the autumn-winter period, after precipitation, the temperature drops sharply. As a result, an ice crust may form on the surface of the web. When opening the canvas, she will interfere with him. To fix this, you need to periodically inspect it and lightly tap on the surface so that the ice and snow come off.

It is often possible to observe a skew of the canvas in the lower part. Because of this, it does not fit snugly against the wall. In this case, it is not necessary to immediately replace the roller shutters. It is enough to check the guides, in which dirt can simply accumulate.

If you ever encounter similar problems with roller shutters, then do not delay the repair. The sooner you find the cause, the sooner you can fix it.

The use of roller shutters has gained great popularity among modern consumers. However, over time, under the influence of environmental factors, even the highest quality and reliable product or its individual element can break. In this case, it is necessary to carry out repairs, which can be easily done by hand. To get acquainted with some of the nuances of this process, you can watch a video that provides answers to many questions.

How to repair roller shutters?

It is not difficult to significantly extend the operating period and prevent serious problems. This can be done with your own hands - it is enough to periodically inspect the bearing and other moving elements. In the photo you can see the components of the design of the roller shutters, after which it will be much easier to repair the breakdown.

There are several signs of a problem, for example:

shaft grinding with a collapsed bearing;
abrasions of the canvas that occur when the silicone inserts are worn out;
skew of the canvas according to the level in the lower part;
uneven convergence;
clogging as a result of the accumulation of debris in the guide elements.

With a collapsed bearing, the repair process consists of several stages:

take a new bearing;
we transfer the canvas to the lower position so that it is completely open;
dismantle the protective cover and shaft;
dismantle the broken element and change to a new one;
we assemble the structure in the reverse order.

If, as a result of the use of roller shutters, an uneven arrangement of the canvas in the lower part is noticed, you can eliminate this problem with your own hands. To do this, make sure that there are no foreign objects in the guides. In the presence of mechanical damage, it is necessary to carry out repairs, after which you can once again check the performance of the structure.

As a result of the operation of the roller shutter structure, various breakdowns can occur, which can be divided into:

The first category includes breakdowns, the elimination of which does not require the dismantling of the structure, it is enough just to replace the broken parts, for example, cardan, rings, bolt, guide elements. In case of more serious breakdowns, repairs may require the dismantling of the roller shutter, if it is necessary to rebuild the canvas, replace the side covers or eliminate the mechanical damage to the box. In the photo you can see the main components of the design.

One of the advantages of protective roller shutters is a simple design, which, if necessary, can be repaired at no extra cost with your own hands. It is enough to take into account the main nuances and follow the safety rules in the process of working with metal structures, having previously studied the instructions for the roller shutter, which indicates the location of the roller shutter system nodes. If it is necessary to eliminate the breakdown of the gearbox or mechanical damage, which may be evidenced by noise in the box, it is enough to perform several basic steps:

lower the canvas and remove the protective cover from the box;

find the damaged element and repair the damage;
if necessary, replace the broken part;
return the protective cover and canvas to their original place.

Among the main breakdowns of an automatic roller shutter, one can note the problematic raising and lowering of the canvas. In some cases, it may not move at all. The main reason may be the breakdown of the crossbar, the repair of which can be done by hand. In this case, you will need to remove the protective cover and make sure it is intact, if necessary, you can replace the broken part.

The occurrence of extraneous noise and scuffs on the side of the web may be an indicator that the sealing tape, which is located in the side parts of the guide profiles, has become unusable. For repair, it is necessary to remove the protective cover and lower the blade. After loosening the fastening of the side cover, you can lift the canvas and remove the guide element. Then it is carefully removed and the sealing element is inserted. When carrying out the repair of various elements of the roller shutter, it is necessary to take into account all the technical nuances.

Roller shutters are reliable and durable metal structures designed to protect window and door openings from breaking, as well as strong wind and rain. Made of aluminum or steel profiles, roller shutters are not subject to corrosion and are resistant to deformation. They could have lasted for more than a dozen years, if not for the specific breakdowns characteristic of roller shutters.Use quick links to navigate the page:

natural wear and tear

Poor product quality

Mounting errors

Intensive use

Harsh climatic conditions

Accidental damage to the blade or guides

Neglect of the rules of care and operation

Vandalism and attempts to open the structure

Some problems are easy to avoid if you order roller shutters from trusted companies. Choose organizations that are responsible for their work and provide guarantees not only for the roller shutters themselves, but also for installation. Premature structural wear caused by heavy use, especially in harsh climates, can be minimized by timely maintenance that should not be neglected. No one is safe from accidental damage and, moreover, vandalism and hacking attempts, and the only thing that remains in this situation is the elimination of damage.Some faults are easy to fix. For example, to replace the guides, the dismantling of the entire structure is not required. You can do this repair yourself. Other breakdowns are much more complicated and require partial or complete disassembly of the mechanism, and one cannot do without the help of specialists. Sometimes the cost of repairs is almost equal to the cost of a new design.Any repair should begin with a diagnosis. It is important not only to identify the malfunction, but also to understand the causes of its occurrence. This does not apply to mechanical damage, when the cause of the defects is obvious. For example, bent lamellas as a result of burglary or vandalism.Most faults are hidden from view under a protective box:

Roller shutter is sagging, warped or broken

Crossbar blockade on automatic roller shutters stopped working

The hand drive cord has burst and the blade cannot be opened/closed

The electric motor burned out, the cardan broke, the gearbox failed

As you can see, most of the problems are related to the drive and suspension of roller shutters. Visual inspection of these units cannot be performed without first opening the protective box. In these cases, mandatory dismantling of the box cover is required in order to accurately determine the cause of the malfunction and then carry out repairs.A common cause of malfunctions is damage to rubbing parts. The moving parts of the lifting mechanism (shaft, bearings, gearbox, cardan), which are responsible for raising / lowering the web, fail due to constant friction. Friction will shorten the life of manual roller shutters by causing the tape or cord to break. Even the lower bolt lock fails, oddly enough, for the same reason.The only solution to a problem caused by wear on a moving part is replacement. There is no point in trying to fix a failed node. You will only waste time and money. Repairs will not last long, but the most unpleasant, artisanal repairs can lead to more serious damage to the structure. And even more financial investment. Image - Do-it-yourself roller shutter repair

The type of roller shutter drive - manual or automatic, affects the nature of this breakdown and determines how to eliminate it.

For motorized roller shutters, the bolt or bolt rings may need to be replaced.

For roller shutters with a spring-inertial mechanism, it is enough to install a new PIM.

The cardan transmits torque between the crank and the shaft, due to which the canvas on the roller shutters with mechanical control rises and falls. A defective cardan is replaced with a new one, and at the same time it is recommended to install a new bearing.

The movement of the web is set according to the scheme: crank-cardan-gear-shaft. The gearbox is the last link that directly rotates the shaft, with the roller shutter leaf attached to it. In the event of a gearbox malfunction, the cardan does not transmit movement to the shaft, respectively, the canvas does not rise. If the gearbox fails, it needs to be replaced.

Not always problems with the course of the canvas are associated with the lifting mechanism.Quite often, the reason lies in a malfunction of the guide device, deformation of the side tires or damage to the side locks of the roller shutter web. In such situations, it is desirable to replace the guide device, and at the same time the guide rollers. Side rails and locks can be repaired, but if repair is not possible, then replacement.

Roller shutters with a manual drive (tape, cord, cord) are raised / lowered by pulling a special tape or a more durable cord. With frequent and / or prolonged use, chafing of the drive may occur. Replacing the cord or tape is a completely justified repair.

Replacing the lower bolt lock may be due to its malfunction - then the striker plate or the entire lock will need to be replaced. Another option is losing the keys. If there is a problem with the keys, it will be enough to put a new lock cylinder.

Do-it-yourself roller shutters: installation (installation), repair. Roller shutters for the closet with their own hands. Gate-roller shutters with your own hands

Roller shutters are one of the types of blinds and have the form of a roll with two guides. The latter run parallel to the plates. Do-it-yourself roller shutters can be installed in window, garage, and doorways.

Before starting the installation of roller shutters, it will be necessary to carry out certain preparatory work. Initially, the opening must be measured, its diagonals must be compared in order to understand if these parameters differ by more than 5 millimeters. It is important to analyze how correctly the slopes are located, the permissible deviation from the horizontal or vertical is 1.5 millimeters per 1 meter. There should be no chips or cracks on the surface of the slopes, and if they are plastered, the finish coating should not peel off.

Before you make roller shutters with your own hands, you need to prepare the side guides. To do this, markings for drilling holes must be carried out. In order to ensure symmetry, they need to be laid in pairs: holes should be made in increments of 15 centimeters from the edges of the guide rails, and only then holes should be made along the entire length with an equal interval of 50 centimeters. If an overhead installation type has been chosen, the holes should be made closer to the outer edge. When carrying out these works, a drill with a diameter of 8 millimeters should be used. If the mounting is to be carried out outdoors, then the through hole of the bar must be made on both sides, while the top bar must be drilled until a diameter of 11.8 millimeters is obtained. This manipulation is necessary in order to mount the decorative cap.

If you decide to install roller shutters on the gate with your own hands, then the box on each side must be drilled so that two holes are laid through the cover, their diameter should be 4.2 mm. They are necessary for installing rivets after completion of work. Among other things, you need to make holes to fix the box. With surface mounting, the holes should be located at the back, while with built-in mounting - from above, combined mounting involves making holes in both planes.

If you are installing roller shutters with your own hands, then at the next stage you need to make markings for the holes into which the fasteners will be installed. The box is attached to the opening. When surface mounted, all elements must be attached to the wall; when mounted, the parts are located on the side and upper slopes. Next, you need to check how vertically the guides are located, and also whether the box is correctly mounted in relation to the horizon. Markings on the slopes through the drilled mounting holes must be made with a marker. You need to drill holes through them, and then drive in the dowels. A hole must also be made for the drive.

If you decide to install roller shutters for the cabinet with your own hands, the technology will remain the same. The next step will be to strengthen the frame. First of all, you should remove the protective film, which is located on the back wall. Fixing should be done with a screwdriver, then you can fix the controls. If an outdoor mounting option is used, the controls must be located indoors. Next, you can install the canvas, and then the box cover, which is fixed with rivets with a gun. All holes must be sealed with silicone sealant, and then closed with plugs.

If you notice a malfunction, which consists in the fact that the canvas is assembled unevenly (this happens, as a rule, most often), then repairing the roller shutters with your own hands can be easily done. To do this, check the guides for the presence of foreign objects. Among other things, the guides may be damaged. But, as a rule, after the removal of foreign elements, the uniformity of the course returns.

10 Adorable Celebrity Kids Who Look Very Different Today Time flies and one day little celebrities become unrecognizable adults Pretty boys and girls turn into s.

These 10 little things a man always notices in a woman Do you think your man knows nothing about female psychology? This is not true. Not a single trifle will hide from the gaze of a partner who loves you. And here are 10 things.

13 Signs You Have the Best Husband Husbands are truly great people. What a pity that good spouses do not grow on trees. If your significant other does these 13 things, then you can.

Why do you need a tiny pocket on jeans? Everyone knows that there is a tiny pocket on jeans, but few have thought about why it might be needed. Interestingly, it was originally a place for Mt.

Top 10 Broken Stars It turns out that sometimes even the loudest fame ends in failure, as is the case with these celebrities.

7 Body Parts You Shouldn't Touch Think of your body as a temple: you can use it, but there are some sacred places that you shouldn't touch. Display research.

In order to increase the service life of the roller shutter, it is recommended to periodically inspect the moving parts, namely silicone inserts, bearings, etc., which are the first to wear out.

There are the following popular malfunctions of roller shutters:

shaft grinding - most likely, the bearing is worn out,
scuffs are observed on the canvas on both sides - the silicone inserts are worn out,
in the lower part, the canvas is skewed - the guides are clogged with garbage, mainly in the lower part.

When repairing roller shutters, you can encounter two types of malfunctions - minor, when you need to replace a small part, and serious, when you need to dismantle the structure and carry out a comprehensive repair. If in the first case you can do it yourself, then in the second case we recommend contacting roller shutter repair specialists, for example, the Gate Service company vorotaservis.com/remont-rolstaven. On the company's website, you can find a lot of useful information on the repair of roller shutters, as well as the contacts of the master in case you cannot solve the problem yourself.

If the bearing is defective, the following steps must be taken:

Buy a new bearing,
Lower the canvas to the lower position,
Remove the protective cover and shaft,
Dismantle the sliding plate,
Changing the bearing
We collect the rollet back.

If the roller shutter blade is not assembled evenly at the bottom, do the following:

Check guides for foreign objects
Check for mechanical resistance,
Remove foreign objects and recheck the mechanism.

The most common problems with automatic roller shutters:

The canvas does not rise
The canvas does not fall.

Can I fix these problems myself? Yes, you can, if you approach this issue carefully.

If in the case of raising or lowering the roller shutter, the canvas practically does not move, while minor movements are accompanied by noise and crunch. Perhaps this is a broken crossbar.

To fix this problem yourself, do the following:

Remove the protective cover
Check the bolt for integrity,
If the bolts are broken, they must be removed,
Install new ones.

If scuffs and noise are observed on the canvas along the entire length, then, most likely, the sealing tape has failed and frayed.

To fix the problem yourself, follow these steps:

Remove the protective cover
Let's drop the roller
We loosen the fastening in the side cover attached to the wall,
Raise the canvas
Unscrew the guide and remove it carefully,
Insert the seal.

Add to favorites

How to repair roller shutters?

There are several signs of a problem, for example:

shaft grinding with a collapsed bearing;
abrasions of the canvas that occur when the silicone inserts are worn out;
skew of the canvas according to the level in the lower part;
uneven convergence;
clogging as a result of the accumulation of debris in the guide elements.

With a collapsed bearing, the repair process consists of several stages:

take a new bearing;
we transfer the canvas to the lower position so that it is completely open;
dismantle the protective cover and shaft;
dismantle the broken element and change to a new one;
we assemble the structure in the reverse order.

As a result of the operation of the roller shutter structure, various breakdowns can occur, which can be divided into:

One of the advantages of protective roller shutters is a simple design, which, if necessary, can be repaired at no extra cost with your own hands. It is enough to take into account the main nuances and follow the safety rules in the process of working with metal structures, having previously studied the instructions for the roller shutter, which indicates the location of the roller shutter system nodes.If it is necessary to eliminate the breakdown of the gearbox or mechanical damage, which may be evidenced by noise in the box, it is enough to perform several basic steps:

lower the canvas and remove the protective cover from the box;

find the damaged element and repair the damage;
if necessary, replace the broken part;
return the protective cover and canvas to their original place.

During the operation of roller shutters, it must be remembered that timely repair and elimination of minor breakdowns will significantly extend the period of their working condition and avoid serious problems. In addition, weather conditions, temperature changes and mechanical stress can have a negative impact. Therefore, if extraneous noise occurs, you should not postpone repairs for a long time.

Professional textile companies are involved in the preparation of materials for this site. designers and technologists garment production

We will be happy to help you choose options for curtains and home textiles for your apartment, which will cost less than if you went to a regular curtain salon

The window opening is the most vulnerable and weak part of the building. Despite good heat and sound insulation characteristics, ordinary glass is not designed for intense mechanical stress. From impact or strong pressure, it instantly collapses. Therefore, glass doors and windows need protection. Previously, wooden shutters were used for these purposes. Now, along with wooden ones, metal roller shutters are widely used.

Roller shutters are a type of blinds that are rolled up. They consist of vertical guides on which horizontal plates slide. Metal shutters are installed on windows, doors, and some garage doors. First of all, roller shutters are installed to protect openings from illegal entry, as well as from hurricane winds, heavy rain and hail.

There are four elements in the design of the roller blind:

Lamellas are horizontal strips of metal, wood or plastic, connected into a single sheet. They close the opening.
Guides - rails along which the lamellas go.
Shaft - the mechanical part of the shutter, on which the web of lamellas is wound.
Protective box. It contains a shaft.

There are three options for installing roller shutters:

Internal installation. The protective box is mounted indoors, and the canvas closes the outer part of the window or door. The most reliable installation and burglary protection option.
Outdoor installation. The protective box is mounted on the outside of the window. This installation method is simpler than the previous one, but less reliable. The box can be broken, the blinds can be raised and the inside of the room can be penetrated.
Central installation. The protective box is mounted at the top of the window opening. It eats up the usable glazing area, so this installation method is used only in extreme cases, when installation in another way is impossible.

Roller shutters can be installed both outside and inside the room:

External blinds mainly perform a protective function. Therefore, the lamellas are made of aluminum or steel. Both materials protect well against penetration, but do not absorb sounds at all. To improve the soundproofing characteristics of metal lamellas, foam is applied, which is applied to the inside of the canvas. Or lamellas are made of thicker rolled products.
Internal blinds. They are mainly installed for decorative purposes, for protection from the sun. Therefore, instead of metal, wood, fabric or plastic is used.

According to the method of opening roller shutters are divided into:

Automatic. The drum is driven by an electric motor. The opening and closing process can be controlled with a remote control.
Manual. The drum moves due to human power.

Wooden shutters on the windows of a country house do not always look like classic ones. These are rather sashes that perform a protective and decorative function. There are several types of window shutters:

With one sash. They close the windows of a small area. Wooden sash with two hinges. The locking mechanism is located on the inside of the window.
With two doors. They cover large windows. The shutters consist of two sheets, each of which is suspended by two or three hinges. The canvases are closed to the center and closed with a lock or latch.
Folding. They close the windows of a large area. Each sash consists of several parts, each of which is hung on hinges. They fold up like an accordion.
Blinds. When open, close the window completely. The slats are not fixed, but with the possibility of rotation. They can be opened and closed as needed. In this case, the frame of the shutter remains motionless.
Roller shutters. The classic version, where the canvas is wrapped on a drum.
Internal shutters. Located on the inside of the window. They are ineffective for protection against hacking. They perform purely aesthetic functions and cover from the sun.

Anti-vandal and protective roller shutters are installed on a wooden house, both during and after the completion of civil works. Installation technology involves performing a series of actions in a certain order:

Video installation instructions for roller shutters:

Roller shutters can be installed both on the outside and on the inside of the balcony glazing. If intrusion protection is not required, then it is better to give preference to internal sliding blinds on windows. Of course, they can be made with your own hands from improvised materials. At the same time, quality will suffer, the service life will be significantly lower than that of factory-made blinds. With your own hands, you can make blinds from paper, wallpaper or wooden plates. But this is rather an unnecessary excess. It is much easier to buy a ready-made version in the store.

Balcony shutters and blinds need to be looked after. Care is washing.

Conventional sliding blinds are removed quite simply. First of all, they are opened to the full size of the canvas. Then they are removed from the wall along with the guide.

Roller shutters are more difficult to dismantle. First of all, you need to remove the protective cover from the drum. If it is fixed on self-tapping screws, then there will be no special problems. It is enough to take a screwdriver and unscrew the fasteners. If it is fixed on rivets, then they must be drilled out with a drill.

After dismantling the protective cover from the shaft, proceed to the web. To dismantle it, it is necessary to open it completely and remove the mounting plate. Then pull the web through the drum.

After removing the canvas, proceed to dismantle the frame. To do this, all the self-tapping screws are unscrewed from the wall, the frame is carefully removed.

Blinds and roller shutters can be cleaned with a sponge and any household cleaner. After washing, dry them thoroughly.

The mechanical and static parts of the shutters break periodically. There are a number of reasons for this:

Intensive use.Each mechanism has a margin of safety, which is calculated based on the frequency of its use. If the intensity of work exceeds the calculated values, then the roller shutters may break before the end of the warranty period.
Poor maintenance. They must be looked after, if this is not done, then the work may fail.

Failure of the electric motor.
Clamping and stopping the movement of the web along the guides.
Problems with the bolt lock.
Problems with the protective box.

The surest solution when a breakdown is detected is to call a repair specialist at home. Do not thoughtlessly pull the shutters, this can worsen the problem. There are a few tips to help fix simple breakdowns:

Often, roller shutters do not close due to frost that forms on the outer surface of the canvas. It is enough to knock on it weakly and the problem will disappear.
If the bottom of the roller shutter is skewed, then do not forcefully try to align the canvas. It is necessary to take a brush and clean the guides, the problem may be in the dirt accumulated there.
If the shutter does not open with the remote control, then you should try replacing the battery.

Video (click to play).

In order to protect yourself from breakdowns and malfunctions, it is better to purchase roller shutters in large, trusted stores. Installation can be done by hand or trust professionals.

Rate this article:

Grade 3.2 voters: 85