In detail: DIY repair of a garden wheelbarrow from a real master for the site my.housecope.com.
For two years of operation, the wheel bearings almost crumbled, in addition, the tire cracked and torn and the camera punctured.
Until the new wheels were brought in, I decided to modernize and strengthen my garden cart a little.
I connected the handles together with an arc almost immediately after the purchase, so it is much more convenient to control the wheelbarrow, moreover, you can do it with one hand.
I also wanted to move the wheels closer to the middle of the body for a long time. I don't understand at all those who designed such carts. Most likely, they took as a basis the design of the wheelbarrow, which was used in the construction of the Belomorkanal. The wheels of these wheelbarrows (one or two) are located at the front, so a significant part of the weight is on the hands. Despite this, nowadays 99 percent of such products have wheels displaced forward. This applies to both garden and construction wheelbarrows, which, in my opinion, are not much different from each other.
In short, I decided to move the wheels closer to the center of gravity. This will slightly increase the distance between the wheels, but the width dimension will remain the same. In addition, increasing the distance between the wheels will increase the overall stability of the wheelbarrow.
All parts were made from scrap metal lying around in different corners, fitted with a grinder and emery.
First of all, I took two steel plates of suitable sizes with a thickness of 3-4 mm, drilled in them two holes dia. 10mm and installed between the body of the body and the plastic pad in the rear wall of the wheelbarrow. The length of the plates should be such that they protrude slightly above the bottom of the trough.
 |
Video (click to play). |
I threw out a thin can in the front, which apparently served to increase the rigidity of the body.
In its place, I installed a steel strip of suitable dimensions. For this purpose, I came across a spring, someone and once straightened.
I adjusted two more plates in size and welded them on.
Two vertical posts - pipe sections with a diameter of about 32mm. Their length is about half the diameter of the wheel, it is selected empirically.
The axis should be 20 mm in diameter, I didn't find one, set it to 18 mm, then I'll think of something.
It is necessary to check that the wheels spin freely, the tires do not touch the body. If necessary, several washers or a piece of pipe can be put on the axle. The bottom of the body should have a backward slope, then, when moving, the arcs will not touch the slightest obstacles or irregularities in the soil, as it was in the factory version.
Then I forgot to take a photo, but everything is clear anyway. In place of the former axis, I attached a piece of pipe, adjusted and welded on pieces of reinforcement dia. 16 mm. Shown below by arrows.
I did all the actions without removing the body, so it is quite simple to make all the strapping.
Now you can remove the trough and boil in inaccessible places.
At the same time paint.
Installed new, more powerful wheels, size 4.80 / 4.00-8. Relatives were 3.25 / 3.00-8.
The bearings were completely without lubrication. In order to somehow prolong their life, he lubricated them with a syringe with MS-1000 grease. On the occasion, I took four more bearings in stock.
In conclusion, he carried out sea trials. 
Having trouble finding a specific video? Then this page will help you find the video you need so much. We will easily process your requests and give you all the results. No matter what you are interested in and what you are looking for, we can easily find the necessary video, no matter what direction it is.
If you are interested in up-to-date news, then we are ready to offer you the most relevant at the moment news reports in all directions.The results of football matches, political events or world, global problems. You will always be aware of all the events if you use our wonderful search. The awareness of the videos we provide and their quality does not depend on us, but on those who uploaded them to the Internet. We just supply you with what you are looking for and demand. In any case, using our search, you will know all the news in the world.
However, the world economy is also a rather interesting topic that worries a lot of people. Quite a lot depends on the economic condition of various countries. For example, import and export of any food products or equipment. The same standard of living directly depends on the state of the country, as well as salaries and so on. How can such information be useful? It will help you not only adapt to the consequences, but can also warn you against traveling to one country or another. If you are a notorious traveler, then be sure to use our search.
Nowadays it is very difficult to understand political intrigues and to understand the situation you need to find and compare a lot of different information. Therefore, we can easily find for you various speeches of the State Duma deputies and their statements for all the past years. You can easily understand politics and the situation in the political arena. The politics of different countries will become clear to you and you can easily prepare yourself for the coming changes or adapt already in our realities.
However, you can find here not only various news from the whole world. You can also easily find yourself a film that will be pleasant to watch in the evening with a bottle of beer or popcorn. In our search database there are films for every taste and color, you can easily find an interesting picture for yourself. We can easily find for you even the oldest and most difficult to find works, as well as the classics known to all - for example, Star Wars: The Empire Strikes Back.
If you just want to relax a little and are in search of funny videos, then we can quench your thirst here too. We will find for you a million different entertaining videos from all over the planet. Short jokes will easily cheer you up and will amuse you the whole day. Using the convenient search system, you can find exactly what will make you laugh.
As you already understood, we work tirelessly so that you always get exactly what you need. We have created this wonderful search especially for you, so that you could find the necessary information in the form of a video and watch it on a convenient player.
I needed a wheelbarrow for my dacha needs. Well, take the leaves there, drag a couple of cubes of sand from the gate. I bought a cheap enkorovskaya one, because expensive ones too ha did not inspire confidence.
I have not yet begun to operate it, as the constructive jamb of the wheel has already come to light. The shaft barely holds in thin supports, the wheel on the shaft sits with a gap of almost five dozen and travels along the shaft to the left and right. In the existing bearing, the cage2 moves relative to the cage1, and 3 - relatively2 (well, this is understandable, there are balls, but the backlash why do you need it.
To begin with, I want to press out the old bearings, pick up new, closed versions (as I understand it, there is 32x15x12). Fuse two journals onto the shaft, place bearings (press or nitrogen) on them. Well, come up with - weld reinforced shaft brackets along its edges. The wheel is made up of spirit halves
, hence the question, press each one from its edge of the shaft, then pull them together, or come up with stops on the shaft (one removable, no arc) so that they do not shift left-right? But then drag the bearing through one journal, and leave it on the other, and plant the wheel assembly. Any ideas?
Shl. I haven’t thought about strengthening the frame yet, I don’t know where its weak points are, the operation will reveal it, and I don’t want to make the wheelbarrow heavier either.
Intuition tells that the game is not worth the candle.
A filthy design, very flimsy. For this reason, it is better to make a wheelbarrow yourself on more solid wheels, which are sold by firms focused on warehouse equipment.
He can take a bar thicker, for example, by 16 for example, leave the middle of the native diameter, for the length of the distance between the bearings, and grind the edges under the existing bearing diameter. In order to assemble this unit and not disassemble it for a long time, take a closer look at the tires from the mokkicks, they have rubber identical to rubber for carts.
By strengthening - there is a kengurin, this is already a plus. The rest depends on the thickness of the trough. If it is thin, then the bottom can bend, and the leading edge can be bent into an arc. It may also be such an opportunity that the edges of the trough are in the horizon, when the trolley is on loading, but it is worth grabbing the handles and the trough bends forward in a healthy way. Concrete is not particularly convenient to transport in such a place, it is liquid, it splashes forward during transportation.
wheels, which are sold by companies focused on warehouse equipment
There the price is probably the same as for the whole car (I took it for 1300r.)
I would do it myself, but it will turn out very heavy, I can only weld a trough from a two, an inconvenient rectangular shape. And I will not take a thin-walled pipe for frame handles anywhere. Last time I took a wheelbarrow from a friend, two wheels from the Carpathians (Riga), a body with a three. handle with pipe. To transport it, hemorrhoids, and to roll it, it comes out heavier than the payload.
He can take a bar thicker, for example, by 16 for example, leave the middle of the native diameter, for the length of the distance between the bearings, and grind the edges under the existing bearing diameter.
But the idea! And the internal widening will not interfere with the bearings, and will not allow moving along the shaft.
With rubber, there is a camera, it seems, does not siphon.
The trough is thin. It's a shame to say six dozen. I also thought to strengthen it, but the electrode cannot even be brought to this thickness.
- Homemade products for summer cottages6.94
- Rubbish in the case5.72
- House, furniture, interior.4.60
- Beauty ! (decorations, decoupage.)4.52
- Auto homemade3.39
- For computer and internet2.31
- Homemade hooligans2.26
- From paper1.14
- Homemade products for fishing and hunting1.14
- Recipes - we cook ourselves1.13
- Gifts, souvenirs and DIY crafts1.13
- Homemade books0.00
- Photos and homemade ideas0.00
- Tools, materials, secrets of craftsmen.0.00
- For all occasions.0.00
I suggest that you familiarize yourself with the story of a summer resident and a real home-builder Valery Gubchenko, how he chose and modified - he strengthened an ordinary garden wheelbarrow, turning it into a universal construction one.
Valery says that it became relevant for him to purchase a double-purpose wheelbarrow for a summer cottage. It is supposed to be used both for gardening and construction.
When monitoring the offered assortment in the Internet and building supermarkets, he saw that gardening differs from building in form and quality. And naturally at a price. Garden ones are much cheaper, but correspondingly flimsy.
In shape - with a lower box body, it is assumed for heavy, but not bulky goods. I drew attention to the fact that quality in most cases is the reliability of the frame.
Wheels and bodies plus minus are the same everywhere.
Production - China, more expensive - Turkey.
There is a galvanized body, there is a painted one.
Well, of course, with one and two wheels.
Price range from cheap to medium.
To the question of how to be with a home-builder, there was one answer to make a universal wheelbarrow from an ordinary one with your own hands. Valery decided to buy one of the most inexpensive and modify the frame himself.
He chose a one-wheel car. Painted. The paint looked better there. When working, there will inevitably be scratches that want to rust. They will be easy to touch up. But the paint falls on zinc poorly. By the way, the quality of painting (powder) is of a very good level.
All welding work, or rather fitting and tacking, was carried out directly on the body itself for an accurate fit. The paint did not peel off from the welding. The wheelbarrow was assembled on six bolts with a diameter of 6 mm. I changed all the bolts to more powerful 10 mm, added another one in the area where I reinforced the frame in the wheel area. It turns out that there was no frame as such - the author made it from scratch. Two arcs, which were originally attached directly to the body, were also reinforced with three struts.
Now they are already solid, but they are still suitable for transportation. The whole wheelbarrow fit in disassembled form in the back seat of a small car.
From the materials it was purchased:
- Bolts, washers, grovers;
- 10 meters of reinforcement;
- Electrodes;
- Paint cans;
Trial - the first day went off with a bang. The result is a powerful car.
Loaded to the limit with earth - no longer fit - fell out. It was so heavy that I could not push in front of me - only pull. Withstood with dignity - not a single squeak.
As a result, from the cheapest wheelbarrow it turned out in terms of power that it is inferior to it even in the most expensive segment. 
The photographs below show the whole process of the work performed:
DIY garden wheelbarrow repair. Replacing the bearing in the wheel.
My garden wheelbarrow began to creak terribly while transporting various loads. So I decided to make an audit of the wheel and found that the bearings had fallen apart.
Replacing the bearing in the wheel of a garden wheelbarrow is quite simple. It is necessary to remove the remnants of the old bearing and measure the diameter of the hole where the new bearing will be installed and the diameter of the axle on which the bearing will be put on.
I bought new bearings and installed them in the place of the broken ones.
After all the manipulations, the wheelbarrow stopped creaking and its course became smooth and light.
Often, by spending very little time, you can avoid additional costs, which are already enough for those who spend the summer in the country and in country houses, caring for buildings, a garden and a vegetable garden. In this particular case, the conversation, or rather, the video sequence, will be about how to bring the wheel of a garden cart back to life in a few minutes. A garden wheelbarrow in the country is never idle: either take out the garbage, then bring up the building materials, then transport the crop. And, of course, with such intensive use, the wheel periodically breaks down: the tire is punctured, the camera bursts, etc. But, before you go to the market and buy a new wheel, see how quickly you can disassemble the wheel, patch up, or, in case of significant damage, replace the camera and tire, and return everything to its original form.
We want you to see how easy it is to replace a punctured, burst, or simply worn out camera. garden wheelbarrow wheels... Of course, we do this job every day and have taken out several hundred thousand of these wheels before we decided to post this video. The video lasts only a couple of minutes, but by watching it and observing the simple sequence of our actions, you will be saved from unnecessary time expenditures.
First you need to unscrew the spool and completely bleed the air from the wheel to make it easier to remove the tire and tube from the disc.
Then we insert the new camera into the tire, be sure to gently spread it around the entire circumference inside the tire.
Once, on a video about repairing a wheel of a construction wheelbarrow, we received a comment from a man, in which he assured us that our camera with a tire was made of soft rubber, and that it was made of oak and it was impossible to do what was shown in the video. So, if you carefully distribute the camera inside the tire before putting all this on the disc, any tire set, of course, if it is matched to the size of the disc, regardless of the softness of the rubber, will definitely fit on the disc.
If we don’t do it with due diligence, then we will not put the kit on a disc.You do not need to watch how quickly the person in the video does this work, he does it all the time, just pay attention to how carefully the tire set is prepared before putting on the disc.
The next step is to insert the nipple into the hole on the disk and with an effort in a circle we insert the pre-assembled set of tires with a camera inside.
We pump up the wheel and close the nipple with a cap. That's all done!
In the video, we use a compressor to inflate the tire, but almost as quickly it can be inflated with a regular car pump. Everything else is done exclusively by hand and does not require any improvised means.
And in conclusion, once again I would like to draw your attention to the fact that if something does not work out for you, then this is happening not because the rubber is "oak", but because the sequence of actions is violated.
We often have to board the wheels in winter, at minus 15. Knowing the properties of rubber, one can easily guess that at this temperature any rubber will be "oak", but we spend exactly the same amount of time as in this video.
It turns out everything is simple. The fact is that there are not so many repair services for this type of tool. Therefore, you will have to solve the problem with the repair of the wheelbarrow yourself. For this, accordingly, you need to know what problems you can face, as well as how to solve these problems, relying only on yourself. Actually, this is what we will talk about in this article.
The wheel burst. According to statistics wheelbarrow for construction and wheelbarrow for garden in the course of their operation, they most often encounter a wheel problem. Here, as a rule, one common problem is highlighted - the chamber bursts or punctures during operation. Of course, in this case, you can try to side the wheel, and then glue the camera with a patch. Yes - the old-fashioned way, but it also has a place to be. However, thanks to the large assortment of selection of this tool, today it is easier to buy a new part than to repair an old one. Accordingly, with regard to the wheel, we note that it is best to buy a new wheel without a camera. The fact is that a tubeless wheel will once and for all save you from the problem of collision with glass and piercing objects.
Another wheel problem occurs most often at the time of overload. The fact is that any wheel on a wheelbarrow has a disc, which is made of metal or plastic. The disc itself is very light and consists of two parts. So, if the wheelbarrow is overloaded, the load on the disk will increase repeatedly, as a result of which the bolts can slip into their own technological hole. If this happened to your car, then you should immediately stop all work, bleed the air from the wheel, disassemble it and put washers with a larger diameter under the bolts. Of course, this is a temporary solution that will save you time to buy a new wheel.
The frame burst. Very often, mainly due to overload, wheelbarrow for construction and wheelbarrow for garden faced with a broken metal frame. In this case, it is best for you, as a home craftsman, to send to the online store in your city and buy a welding inverter. Of course, this approach will not allow your equipment to remain collapsible as it was with bolted connections. However, the use of a welded joint will make the wheelbarrow structure more rigid and, as a result, more durable.
The wheel of the construction wheelbarrow is rubbing against the supporting frame. We have already said that a construction wheelbarrow and a garden wheelbarrow should not be overloaded during operation. However, its users are very often neglected. Actually, it is precisely because of overload that the wheel on the wheelbarrow begins to rub.The reason for this can be the distortion of the axial part, as well as complete or partial destruction of the bearing system. So, in the first breakdown, it is very often necessary to change the bearing axial parts. In the second, the wheel changes as a whole.
The body has become highly mobile. As a rule, a construction wheelbarrow and a garden wheelbarrow under the influence of a load can lose their strength and become unbalanced. However, this problem is even simpler and can be solved with a simple diagnosis and inspection of your instrument. So, in the process of diagnostics, it is very important for you to determine which of the bots on the car body is weakened. So, as soon as you find it, just tighten the necessary nuts and that's it, your car will be back in service at the proper level of quality.
As you can see wheelbarrow for construction and wheelbarrow for garden have not so many problems, but even those that do exist are easily solved by replacing something or repairing with improvised means.
Whatever one may say, the wheel is the most vulnerable spot on a wheelbarrow. At the same time, it is often destroyed not due to overload, but becomes an object of impact on it with piercing objects. This is the case, therefore, in order to avoid this problem, we have to change the wheel to a new one, since repairing the old one is not always possible. So, when replacing a wheel with a new one, you need to choose a certain type of wheel from the following selection range:
Pneumatic wheel. This type of wheel is considered the simplest and most common, since it is included in almost all wheelbarrows, both low and high price ranges. The basis of such a wheel is the air that enters a special chamber under the action of a pump. It is believed that the pressure in the chamber should be no less than 2 atmospheres. Note that such a wheel is relatively inexpensive, but it can also cost half the total cost of a wheelbarrow construction and garden modification.
Cast wheel. This type of wheel also has such a name - tubeless. They tend to be significantly more expensive and are only available with a metal disc on the market. The advantages of such a wheel include durability and ease of use. Indeed, the wheel does not need to be pumped, which means that there is no need to waste time on maintaining it. Note that many garden wheelbarrows of St. Petersburg are equipped with such a wheel, which are presented on the domestic market with a large assortment of choices. Note that garden wheelbarrows SPb on a tubeless wheel have a long service life because there is no chamber with air inside. Therefore, such garden wheelbarrows cannot be punctured or cut with a sharp object. Note that the tubeless tire itself is very durable, which significantly reduces the wear of the wheelbarrow during operation.
Summing up this article, we note that everything that wheelbarrows, construction and gardening, in general, are very strong and durable. All these nuances and problems are just isolated flaws that, with a very high probability, will not affect you. However, you must be prepared for anything so that, if necessary, provide first aid to your construction or garden wheelbarrow.
DIY garden wheelbarrow repair. Replacing the bearing in the wheel. My garden wheelbarrow began to creak terribly.
In the new video of our channel, I Alexander Filimonov want to tell and show you.
Take your time to throw away the broken construction and garden wheelbarrows, they can be repaired by yourself. I'll go.
Discounts for tools Tools from China https://ali.ski/HYGQB Discounts https://ali.ski/sM3JG Tools in Russia.
How to strengthen a garden wheelbarrow so that you can carry not only grass in it, but also concrete, stones and various heavy ones.
Breeding worms prospector. the California worm is becoming a priority condition for getting ecologists.
They asked to repair the garden wheelbarrow. Fast and cheap, that's what came of it. During the renovation.
Hello. The construction site takes a lot of money and for this I want to show how you can save money.
In this article, the site "How it is done" will tell you how to do garden wheelbarrow repair on one's own.
If you have a different model of a wheelbarrow, it's okay, because their wheels differ only in size.
If there is a puncture of the wheel of a garden wheelbarrow, it is not necessary to change it entirely. You can simply replace the camera.
First, determine the size of the wheel using the markings on the tire and buy a new tube of the appropriate size.
Then remove the wheel from the wheelbarrow frame.
Remove all wheel bolts and slide the old tube out of the tire.
Check again that the markings on the new tube line up with the markings on the wheel of the wheelbarrow.
Then place the new tube in the tire and reassemble the wheel.
The wheel with the new camera is assembled and can be installed back onto the frame.
After that, with the help of a pump, we pump it up to the desired pressure.
Replacement of the wheel chamber of the garden wheelbarrow is completed.
To see clearly how to replace the camera in a garden wheelbarrow, we recommend watching the video:
