Do-it-yourself vaz 2110 interior repair

In detail: do-it-yourself vaz 2110 interior repair from a real master for the site my.housecope.com.

Leatherette is considered an ideal material for reupholstering door cards VAZ 2101 - 2107 or as it is also called vinyl leather. But if we consider vinyl leather in more detail, then it is much stronger than the familiar leatherette. And when buying, you can stumble upon a wide choice not only among colors, but also among textures.

When buying vinyl leather, you should pay attention to a very important detail, namely, its ductility, since it is viscous vinyl leather that can tightly fit all the protrusions of your car. And by the way, it is viscous vinyl leather that is called automotive.

Full restoration of the entire leather surface, as well as velor and vinyl leather upholstery of the entire car interior, complete upholstery repair.

During the operation of the car, the entire upholstery of our salon suffers greatly. And agree that it is always unpleasant. A complete replacement is a rather troublesome business, and besides this, it is not cheap, but there is always the opportunity to repair it yourself.

It is quite easy to make an exclusive interior lighting. It is necessary to put a lot of LEDs in the ceiling of the car and then the "Starry Sky" will not only illuminate the entire interior, but also pleasantly impress your passengers Read more →

The upholstery from Priora fits the Avto VAZ 2112 almost perfectly. I can’t say about Avto VAZ 2110 and 2111, because I have not seen a picture or opinions. so let's start talking about Auto VAZ 2112: Continue reading →

The door trim from the Priors is installed in the VAZ2110 without problems, because. the seats fit perfectly. But you need to change the wiring in the front doors, because the control of the ESP (glass lifts) is carried out from the doors, and not from the tunnel between the seats, as on the 10-ke. Continue reading →

Video (click to play).

Here, the usual option “picked up and put” the Priora torpedo on the VAZ 2110 will not work. there are differences in the wiring, both with the old panel and the euro panel with the new dashboards.

What the Priora panel looks like in the Auto VAZ 2110 is a matter of taste. Someone likes the euro panel, someone likes the panel from Priora, and still others are generally satisfied with the ancient panel 10 Read more →

Often the wife asked why there is no mirror on the sun visor? I think a girl should get into the car already made up, but what if she is used to wearing makeup in the passenger seat? Here you can not do without a mirror in the visor.

In the VAZ 2110 luxury, a mirror is installed in the passenger's sun visor, what about the owners of cars with the usual equipment? It is unlikely that you will be able to buy visors with a mirror for 2110, but you can simply embed a mirror into the visor. Continue reading →

If you decide to remove the entire torpedo, then follow this photo instruction.

It will be more convenient to put a pad on the torpedo if it is removed and lying in the house. Remove the standard panel overlay according to the instructions.

Buttons glass lifts Kalina have a much nicer look and more comfortable shape. Therefore, many owners of the VAZ 2110 decide to change the standard ESP keys to Kalinovskie. How difficult is it to make this replacement?

There are 2 types of Kalinov's ESP keys: low-current (multiplex) and power.

In order to install low-current ESP keys, you will need to install an electric package control module / electric package controller (2170-3763040). Continue reading →

It is believed that fitting a torpedo is not an easy task, the complex shape does not allow the torpedo to be drawn without seams. The visor of the VAZ 2110 torpedo is no exception, which, in addition to its own complex shape, also has a set of keys. Below we will answer the question of how difficult it is to fit a torpedo on your own. Continue reading →

Road safety is linked to driver comfort.Convenience is made up of a huge number of factors, including the armrest. The armrests on the doors are designed for convenient location of the driver's or passenger's hand. In this article we will describe how to increase the armrests on the door card. Continue reading →

To make your trips in the car interior pleasant, it is important to keep it clean. It is much more convenient to clean the interior when there are mats under the feet of the driver and passenger. In this article, we will analyze how to make rugs in the car with your own hands.

Ask why make a rug with your own hands, when you can easily buy rugs for a car of any brand, if not in the auto market, then you can order it in an online store. Continue reading →

The interior design of our cars has never stood out for its beauty, for example, the old, low panel (torpedo) and a small tunnel between the seats did not provide any convenience. If we talk about the tenth generation VAZ, then you can make the interior of the car better if you put a europanel and modify the tunnel. Continue reading →

Where does the upholstery of the cabin begin? Naturally, from the removal of the car seats. It is most convenient to plan the placement of fragments of leather and alcantara on the cover of the waist, when the chair is removed, we sign each part of the standard cover, indicate the name of the material from which we will cut, a simple marker is suitable for this, mark it with a marker on the standard cover.

A frequently asked question is where to buy and how to put your own hands on a euro panel or an overlay on a torpedo on a VAZ 2110. This is not surprising, the ancient panel of dozens is already tired and hunting, somehow update the interior. In this article I will show what is needed in order to change the old VAZ 2110 torpedo to the euro and many important points that you will encounter when replacing an old torpedo. Continue reading →

Any car owner who is used to driving behind a tinted car dreams of such a button, when pressed, the tinting will disappear, and then appear as if by magic when the same button is pressed. Continue reading →

All VAZ 2110 drivers are faced with a problem - it's hard to open the glove box, especially in winter. In severe frost, you have to use a special tool to open a tight glove box. You can solve this problem by lubricating the glove box. First we need to remove it by unscrewing 2 screws. Continue reading →

What can be said about the factory interior for the VAZ 2110 model? It is quite reliable, durable, well-organized internal space, which has a positive effect on capacity.

But the level of comfort here is frankly low. In this regard, many owners of dozens decide on a partial or large-scale stage of improving the interior of their car.

Today we will talk about the elements that can be improved, as well as share ideas and give useful recommendations.

In a special table, we will tell you which elements can be replaced in the VAZ 2110 cabin, and what are their features and advantages.

Interior element

Peculiarities

Its replacement has a positive effect on the appearance of the cabin, the level of sound insulation increases, if appropriate work is carried out. Plus you can install more impressive acoustic equipment

Here you can go different ways - use covers, alter the standard interior or purchase a complete interior from another car. The choice depends largely on your budget.

Modifies the appearance of the cabin, provides better information content. You can either modify the standard panel or use panels from other cars

It is not necessary to completely change the pedals, since there are special linings. They look good, provide more comfortable pressing

Installing a new audio system will have little effect on the appearance, but the sound quality is seriously affected

The factory steering wheel is not particularly original and beautiful. It is often changed to new ones, from more recent Lada models or imported cars.

There are many accessories with which you can completely or pointwise change the appearance of the cabin, increase the level of ergonomics, comfort

If your VAZ 2110 is not designed for the long term, it does not make sense to invest a lot of money in finalizing the interior. If the car stays with you for several years, it is quite possible to improve ergonomics and comfort for yourself personally.

Now let's talk about some points of finalizing the cabin in more detail.

To change the door trim of your car, you first need to get rid of the old one. For this:

Unscrew the fixing screws holding the factory trim;
Remove the latch to get the glass lowering handle;
Dismantle the panel where the handle is held to open the door;
Unscrew the lock button;
Pry off the cover with a screwdriver and remove it. It is held on by plastic caps. If you break them, no big deal. Buying new ones is not a problem.

Then proceed at your own discretion. You can purchase a completely ready-made kit, or do everything yourself, choose the material you like.

Since you are removing the door trim and planning to install new acoustics, it will not be out of place to improve the standard sound insulation by gluing 1-3 layers of sound insulators.

Now let's talk about upholstery, chairs, seats. Let's say right away, if you remove the seats to replace the skin on them or to install a completely new interior from another car, it is better to take care of the sound insulation issue. Alas, the factory noise is ineffective for dozens, which is why inside the car, even when driving at low speeds, it becomes very noisy.

Having finished with soundproofing, we decide what to do with the interior.

T-shirts, covers. The most budget option that allows you to significantly transform the appearance of the cabin. Installation is easy, does not require special knowledge and skills. But the changes will only be external. The level of comfort of the landing of the driver and passengers will not change.

New upholstery. Not everyone can change the interior with their own hands. But this does not make the procedure impossible. The bottom line is to remove the old sheathing material, and instead sew on a new one. In parallel, you can replace the foam rubber in places, slightly modify the design. The option is quite heavy in execution, but allows you to make, in fact, a completely new interior.

Salon from another car. The level of ergonomics of regular chairs leaves much to be desired. Even by replacing the skin and placing a few pieces of new foam rubber, you will not be able to significantly change the comfort of landing. A completely different matter is the installation of a completely new salon with comfortable armchairs and a sofa. The downside is the high cost and the search for a suitable salon for dozens of foreign cars. But there is a serious plus - you can transform not only the appearance of the car, but also seriously increase the convenience and comfort. It's worth it if the car stays with you for the next 5 years.

Stylish, modern armchairs

Does it make sense to change the native dashboard to something else? Here opinions differ. But many note that such a refinement is relevant if it is planned to install additional equipment, indicators, sensors on the car. That is, we are talking about fans of not only external, but also technical tuning.

There are several ways to customize the dashboard.

Modify the panel with your own hands, using luminescent paints for arrows, notches, marks on the instruments. You can also install LEDs, a tachometer, other "chips", cover with a carbon film and so on.
Another option is to buy ready-made inserts that just need to be installed. Today, for a dozen of their range is quite extensive.
Remove the old instrument panel and put in its place a new, more modern one with arrows or an electronic type.
Use the dashboard from another car.

When changing the dashboard for equipment from another car, you will have to modify, customize everything, solve the issue of wiring, connecting sensors, etc. The task is not an easy one, it is better to perform it at specialized car services.

Using all sorts of accessories and tuning elements, you can modify your standard interior without serious investment, distinguish it from dozens of others.

Let's talk about some of the accessories.

Pads on the pedals. They are not expensive, but they significantly transform standard, far from beautiful pedals.

Stickers imitating carbon, metal, wood. They are usually glued to the glove compartment, center console, doors. Such films are cheap, but they seriously change the appearance of the car interior.

Steering wheel. Using a new steering wheel to replace the old one, you will increase the level of comfort, provide easier driving. You can either completely replace the steering wheel, or alter the old one, make leather or leatherette upholstery. The main thing is that the material does not slip in the hands.

LEDs. Lighting elements that can be mounted anywhere. They consume a minimum of electricity, so you should not be afraid of a rapidly discharging battery. LEDs are used to illuminate the interior, pedals, glove box, etc.

Rugs. The simplest accessory that performs two functions - collecting dirt so that it does not accumulate on the floor, and an external decoration.

Electronics. Although the VAZ 2110 is a budget car, no one bothers to refine the interior by installing high-quality navigation equipment, a DVR that is useful today, a monitor on the ceiling, modern acoustics, etc.

How can LEDs be used?

When installing volatile equipment, take into account that it will affect the battery life, the reliability of the standard wiring. With such improvements, it is better to take care of installing a more powerful battery, as well as replacing wires, the parameters of which are not designed for this level of consumption.

Salon dozens has its advantages, positive qualities. Therefore, refinement is the choice of each individual. We have listed the available options for improvement, so choose and get to work.Despite the fact that interiors that use white material get dirty faster, they look quite attractive. New cars with such an interior cost a lot, but you can replace it yourself in your car, spending not as much time as it might seem at first, and saving money. This article will discuss which interior elements can be upgraded, and the process of replacing a standard interior will be described.The factory interior of this car is quite reliable, and the space inside is organized quite well. But the VAZ 2110 is unlikely to boast of comfort in front of modern cars, so many of its owners strive to at least slightly improve its interior.The following parts can be improved:

Replacing the door trim to improve the appearance and increase noise insulation.

Replacing the upholstery of the interior. In this case, you can alter the interior yourself or use the finished interior of another car. It all depends on the owner's wallet.

Dashboard changes. At the same time, you can significantly expand its functionality, use the panel of another car or upgrade the old one.

Install special pedal pads and replace the gear lever.

Installing a new steering wheel, since the factory one is not original.

The use of various accessories that will affect the appearance of the cabin and make it more comfortable and ergonomic.

Parsing the cabin will not be difficult and will take no more than 3 hours, even for a person without experience.First you need to pull out the car seats so that they do not interfere with work, then gradually remove the entire interior trim without damaging the wiring of the panel. There are a lot of wires here, so it is imperative to mark each connector so as not to be confused when reinstalling.The wiring must also be removed and inspected for cracks, signs of corrosion or burnout in the factory winding. In most cases, after a long period of operation, the wiring of the car needs to be replaced.To do this, perform the following steps:

Familiarize yourself with the diagram of the electrical equipment of the car;

Remove the front panel of the cabin;

Carefully inspect the wiring, especially those wires that are connected to the wiper mechanism and headlights of the front group.

Dismantle the damaged wiring and replace it with a new one.

First of all, it is necessary to dismantle the factory upholstery. This must be done carefully and approximately in the following sequence:

Using a screwdriver, unscrew the screws that hold the factory upholstery.

Remove the handle for lowering / raising the door glass, for which you must first remove the latch.

Remove the panel holding the door handle.

Unscrew the door lock button.

Lightly pry up the upholstery with a screwdriver and carefully remove it. For its fastening, plastic caps are used. They can be broken when removing the skin, but this is not a problem - you can buy new ones in the store.

In terms of the need to refine the factory dashboard, opinions differ: someone is satisfied with the existing one, the rest want to redo it a little in order to install additional sensors, indicators and other elements.Ways to refine the dashboard:

It is possible to upgrade the instruments themselves using luminescent paint, which is applied to the hands and marks on the instruments. If desired, you can add a tachometer, install LED bulbs, etc.

Buy ready-made inserts, the range of which is quite large.

Replace all devices completely with more modern ones, with arrows or an electronic display.

If there is a panel of another car available, use it. In this case, there may be problems with electrical wiring, fitting the panel housing. Therefore, it is not recommended to do this on your own without experience.

As a material, you can choose inexpensive leatherette. It is easy to process, cut out pieces of the desired shape, glue. However, it also has some disadvantages:

Poor resistance to mechanical stress;

Wears out faster than genuine leather.

Does not tolerate temperature fluctuations.

But leatherette is much cheaper than leather, so it was decided to choose it as the main material for the new salon.For a new skin, you will need about 4x2 meters of matter (it is better to take it with a margin), out spirit, glue 152I, a lot of patience, since the work is quite painstaking. The best option would be special glue 88, which can be purchased at a specialty store, but the glue listed above also did the job.All work is best done outdoors or in a garage. The glue is quite toxic and has an unpleasant odor, which is very difficult to get rid of if you work directly in the apartment.A clerical knife and scissors were used to cut the material along the contour. Scissors need to cut a rectangle, which is then attached to the panel. Trimming can be done with a clerical knife along the contours of the panel, while leaving a margin. Glue must be applied both to the panel itself and to the mating surface of matter, and wait 10 minutes. After the glue dries, you need to put the fabric on the panel and gently smooth it out so that there are no wrinkles. It is advisable to perform this procedure the first time. If it was not possible to immediately glue evenly, you will have to tear off the leatherette lining, on the surface of which glue can come out.Smaller parts of the panel are much easier to glue with a leather substitute, so special attention must be paid to large parts.The configuration of the main panel is rather complicated, so it is unlikely that it will be possible to cut a whole piece of leatherette according to its shape. It is best to divide it into parts by marking with a pencil:

The left side of the panel to the console, near which draw a line with a pencil;

Console directly;

The right side of the panel, on which there is a glove compartment.

After gluing the material, it is necessary to assemble all the elements of the panel and visually check whether everything worked out correctly.Now it is necessary to glue all the joints and interfaces of the plastic elements of the panel with Madeleine, using a sealant to coat the air ducts, since they have rather large gaps. Splenite 4 mm thick can be laid inside the panel.From the door upholstery, the removal of which was discussed above, it is necessary to remove the top layer of factory material. This is necessary in order for the leather substitute to adhere better. In the same way as leatherette was glued to the panel, it is necessary to cut the material along the contour, grease the mating surfaces with glue, wait 10 minutes and carefully combine them. Optionally, you can also glue a cord with neon lights in the area of the door handle. So it will be more noticeable in the dark, and the door will look even more attractive.Similarly, it is necessary to glue the upholstery of each door.First of all, it is necessary to dismantle all the remaining interior elements, thoroughly clean and wash everything.Vibration-absorbing bituminous material must be installed on doors, ceiling, motor shield, floor tunnel and arches and other surfaces. You can use Vizomat MP 4. You can also dismantle the rubber plugs that close the technological holes in the bottom of the car. In place of them, it is better to install the Visomat, while doing this both from the side of the passenger compartment and the bottom.Splen 10 mm was used as sound insulation, and a factory sound insulator can be laid on top.Before installing the panel, you must connect all the wiring and check its operation, since removing and installing the panel again is a rather difficult process.Next, you need to install the panel in place. Difficulty can arise if too much soundproofing material has been used, the excess of which must be removed. It is also quite difficult to install the panel into the guide pins, which are located in the area of \u200b\u200bthe furnace.Plastic pipes can be installed in the air duct for supplying air to the legs and the gaps can be closed with mounting foam. Perhaps it will not look very aesthetically pleasing, but the legs will be warm.A GPS navigator can be installed in the central deflector. To do this, you need to remove all the jumpers, file the opening a little. For installation, you will need epoxy, fiberglass, putty and a primer.Seat upholstery can be done independently, or ordered from the car manufacturer. If it was decided to modify the seats yourself, you can choose one of the following options:

Install new shirts and covers. New elements will only visually change the interior, but will not affect the comfort of the driver and passengers.

You can make the skin with your own hands, which may not work for everyone. After removing the old material, it is advisable to replace the old worn out foam rubber.

Install seats from another car. But finding suitable ones for the VAZ 2110 is quite difficult.

To make your tunnel, you will need a 4 mm thick plywood sheet and cardboard sheets to create templates.First you need to install the lower part of the factory tunnel. Then, using sheets of cardboard, make templates for cutting a tunnel out of plywood. On the resulting tunnel, it is necessary to glue the leatherette material and screw the resulting product to the factory tunnel.The simplest, but at the same time inexpensive and effective way, is to make overexposure using single diodes and a diode strip. You can choose any color you like. The main thing to remember is that the dashboard will be in front of your eyes all the time while you are driving. And too bright, catchy colors can significantly increase fatigue and irritate the driver.Also, the backlight can be matched to the color of the car. Both in tone and in contrast. In addition, external lighting is often done, then it is important that the colors must be combined. Therefore, if you plan to do tuning not only in the cabin, be sure to decide in advance in what colors and which one. So that in the end the car looked holistically and harmoniously. If this is not done, you can achieve the effect of a Christmas tree. And instead of stylish tuning, get a "collective farm" option.As a rule, backlighting is done on the following parts of the panel:

the panel itself along the edge;

clock;

oven damper regulator.

The interior and body can, and sometimes need, be illuminated in the following places:

put separate lighting for the rear seats, which will not intersect in direction with a common salon lamp. This is also necessary for small children who are afraid to drive in the dark, and just for passengers who suddenly need light on the go. After all, such a backlight does not interfere with the driver at all. By the way, that’s why it’s worth choosing soft, not too bright diodes for it;

illuminated glove compartment, both inside and outside, it is not only very convenient, but also very beautiful, bright and stylish;

the backlight in the legs looks good, moreover, both for the passenger and for the driver;

of course, a bright light in the trunk is an extremely necessary, important and really rational addition to the standard car lighting;

to duplicate the illumination of the number is also a very worthwhile addition;

backlighting with diodes instead of running lights is currently very popular, both because of its economy and for its stylish and bright appearance.

Thus, it is a great idea to make car tuning with the help of backlighting with both single diodes and strips of them. And most importantly, available to almost every motorist. After all, materials will require very modest investments. And the installation of some complex and rare skills will not require.But anyway, if you do not have real experience with a soldering iron and LEDs, it is better to find a master or just a friend who knows how to handle all of the above. And ask him to help in the installation and installation, at least at first. And then, when your own skill appears, continue the installation yourself.This section is devoted to tuning the VAZ 2110 car with your own hands. You will find a lot of interesting information on tuning your VAZ car. All articles are written by real owners of the VAZ 2110 and have been put into practice.Probably every owner of a VAZ 2110 car sooner or later faces such a task as the need to replace the timing belt or timing belt for short. The timing belt must be changed every 45 - 50 thousand car mileage.A car alternator is a device that generates current to ensure the continuous operation of the car's electrical appliances. Battery charging, mains voltage in the car, etc. depend on this device. It is very important to know which generator is best to choose for the VAZ 2110 - 12?The cabin filter allows you to clean the air entering the cabin from exhaust gases and dust. We can say that the cabin filter protects the human respiratory system. The cabin filter, series of the tenth VAZ family, is located after the air intake, but in front of the heater.The main task of any filters in your car is to prevent dust from entering the engine or car interior. The fuel filter purifies gasoline; air - air supplied to the carburetor (injector); oil - the oil in the engine.It is best to change the filters on time so that you do not have to pay extra money for the repair of your car later.If your fan does not turn on, which cools the car's radiator, the coolant sensor may be the cause. It is this sensor that is responsible for cooling the car radiator. I want to say that if you find such a problem in yourself, do not rush to change this sensor. Don't spend extra money. The best thing to do would be to test it to see if it works.At the initial stage of reworking your own car, much attention should be paid to tuning the VAZ 2110 panel. Many owners of the "tens" adhere to the position that their car should not lag behind modern fashion trends in the world of four-wheeled high-speed "iron horses".Of course, everyone wants his car, despite a certain wear and tear and already quite a rich history of the VAZ 2110 brand, to look beautiful, “feel” powerful and provide high comfort inside the cabin for all passengers. In the process of moving on a vehicle, many passengers pay attention to the instruments.Of course, they will always be more interested in original devices with exclusive design solutions that literally amaze and delight. Tuning the instrument panel VAZ 2110 should begin with a search for panels. To install such a part, you will have to use your own skills and dexterity if you do not want to give your hard-earned money in various car dealerships.Moreover, this work does not require the use of special tools. It will be enough to use pliers and a Phillips screwdriver.The whole process of updating the instrument panel with your own hands will not take much time. All that needs to be done is the dismantling of the obsolete “part” and the installation of an upgraded model. How to remove the VAZ panel can be found here and in the car repair and maintenance manual. But the main steps should be recalled:

First you need to disconnect the battery terminals. The steering wheel should be lowered to the lower position.

it is necessary to unscrew the fastening screws of the panel lining.

then we disconnect the connector on the left, in this situation we are talking about a machine switch for outdoor refreshment. Then, using pliers, you should unbend the fastenings of the instrument cluster.

Next, we remove it. Some models are fixed with M5 screws. At the end, you need to disconnect the connectors.

After that, you can install a new panel in reverse order. Such a do-it-yourself VAZ 2110 tuning will always arouse admiration among passengers and a sense of their own pride.Today, the fashion to change the backlight of the dashboard is gaining fantastic momentum. Almost everywhere, cars have neon lights or internal LED illumination. However, all these innovations are an expensive pleasure, which not everyone can afford. Otherwise, the situation is with the replacement of the factory backlight with a multi-colored one.You can, no doubt, use ready-made tuning options, but this will also cost a lot. It is best to do it by hand. In this situation, the main thing is to have the necessary materials and patience. First you have to disassemble the "tidy". The protective glass needs to be removed. Next, remove the arrows. To do this, you need to use a screwdriver and hard cardboard.It should be placed under the arrow, and then pry it with a screwdriver. Then gently and slowly lift it to the top. Next, remove the backing. For this you will need a utility knife. It must be inserted between the panel and the substrate and cut through the sealant layer in a circle. Then we remove the backing. We disassemble the panel and begin.1. Remove the filter layer using a clerical knife. A light filter is a colored layer of paint. It is applied from the back of the substrate and gives color illumination to the speedometer numbers and other gauges. To completely get rid of the filter, you can use acetone or another liquid that contains alcohol.2.Next, change the highlight color. First you can change the backlight of the odometer. To do this, you will need to dismantle the odometer screen, and then remove the blue film and remove the backlight bulb. It should be replaced with a multicolor universal LED. He can change colors. We attach the LED to the standard bulb holder. Install the odometer screen in place.3. Now you can proceed to the complete replacement of the backlight. We fix the LEDs to the frame of the "tidy". Such LEDs can be bought complete with a color switch. We install them in place and attach them to the standard contacts of the backlight tidy. Image - Do-it-yourself vaz 2110 interior repair

4. Go ahead. Now you need to make sure that the arrows have the ability to change the backlight. To do this, remove the layer of red paint from the arrows. For this operation, you can use a clerical knife and acetone. Once the arrow is clean, it can be painted using white nail polish. The main thing is that the arrow is white, since this color conveys the color gamut of the LEDs.

5. Before the final step, you need to fix the LED color switch on the panel. Such a switch can be installed, for example, in the lower right corner of the "tidy". After that, you can install everything in place. The substrate is installed first. For greater reliability, you can use a sealant. After that, set the arrows in place. Insert protective glass. After that, we admire the result.

When tuning the panel of the presented car, among other things, you can also beautifully highlight the “dashboard” buttons. Take, for example, the button for turning on the rear fog lamp. First you have to dismantle and disassemble it. To do this, you need to pull in different directions its moving part and body.

After the button is pulled out, you can access the incandescent lamp. If you wish, you can take it out. If you can't get the bulb out, then move on. Using a screwdriver or a knife, pry the latches on both sides. A switch mechanism will appear in front of us. Here we need a black brace. By prying it, we will calmly scatter the entire mechanism.

Now we can easily remove the lamp, tweezers are suitable for this. Now you can connect fantasy. You can buy a LED lamp of any color. It should be borne in mind that the positive is contact No. 6, and the negative is No. 7. Polarity can be found by looking at the back of the case. A block with wires is inserted here. Next, we check how the backlight works. If everything is fine, move on to the next part.

Get rid of the green light filter. It can be drilled, it must be done carefully so that the drill does not pass through the entire structure. As a result, we remove the light filter from the structure and check its performance.

It should be noted that almost all buttons, if desired, can be modified in this way. The only exception is the position of the negative and positive contacts, they must be viewed from the wiring diagram. If there is no diagram, you can easily find her photo on the Internet. The negative contact is usually denoted by a black wire, positive - of any color.

Most often it is white. You can remember, but it is better to sketch or photograph the contact connections, then there will be no confusion during the assembly process. The assembly process must be done in reverse order.

You can beautifully complement the panel with the installation of a tweeter (tweeter). One of the most problematic stages is drilling holes. The windshield prevents drilling at right angles. But it is impossible to do without a drill, because there is a metal strip under the plastic shell. In this situation, paper should be made like a template or stencil.

Using a knife, you can remove the soft area of \u200b\u200bthe panel (on the outside - plastic, on the inside - a kind of foam rubber). Then we take a drill and drill around the previously marked area. It is better to use compact drills.When the hole is drilled, the jagged edges should be corrected. To do this, you can use special nozzles for drills.

You need to drill at a distance from instruments and sensors. It should be noted that wires or brackets may come across under the metal strip. The tweeter element to be mounted must fit snugly into the hole. If there is a certain freedom, then it is necessary to seal this area with a sealant. The wires from the tweeter can be hooked along the edges of the air ducts.

This tweeter is an important component if an acoustic system is built in the car. Without such a detail, the sound and volume of the sound will not be complete.

The domestic car 2110 cannot boast of a high-quality panel. In severe frost or summer heat, plastic often begins to crack. In addition, sometimes its corner also peels off. The “tidy” of this machine consists of three parts: a central, upper lining and a lower plastic lining. The corner is most often peeled off through: unscrewing the screws that attract the top lining, or through the fact that its soft part has moved away from the metal part of the top lining.

In the first option, you need to remove the panel, because otherwise it will not work to tighten the top trim. If only the soft part has departed, then there may be several solutions. You can glue it, but it won't hold tight, on a plastic air deflector. Another option is to mask the gap that is formed when the corner of the panel is peeled off.

You can, no doubt, cover the gap with a wire. It is placed inside using a screwdriver. Instead of a wire, you can use a headlight seal. In this case, you can return the corner to its place. For gluing the corner, use foam. The skin, thanks to the foam, will stick precisely to the metal case, but first it needs to be cleaned and degreased.

Then we apply the foam inside, with the help of a wet rag we remove the excess foam. We press the corners with paper clips. It is not necessary to remove the foam immediately. You should wait until it dries. After the foam dries, you need to paint over it with a marker. It may seem that the foam is bursting, but in fact, the corners of the panel will not come out.

Now you can proceed to repair the crack on the panel. To do this, either use a plastic repair tool, or overtighten the overlay with material. As for the first option, it is the simplest, because during the repair it is not necessary to remove the lining. You can remove the crack using a special epoxy resin.

Cosmophen and cold welding are also suitable for use. To prevent the crack from standing out, the dashboard should be repainted. In the second method, when hauling this automotive part, leather or leatherette is used. First, the crack must be patched. If the problem is in the corner of the panel that has peeled off, then it will not be difficult to repair it.

If the “tidy” is cracked, then it is very difficult to completely hide the crack and, at the same time, not remove it. If the matter concerned the repair, then it is better to immediately replace it with a euro lining. Here you can see in detail how to solder plastic.

A boring regular panel (on video) quickly bothers many owners of the VAZ 2110, but I don’t want to buy an alternative one that is equipped with a computer and costs a lot of money. What to do in such a situation? There is a great option that will allow you to do economical tuning with your own hands. One of the easiest ways is to buy an overlay.You can find them without any problems in online stores (the photos presented there give a general idea of \u200b\u200bsuch details). To install it, you need to remove the "tidy" and carefully pull out the arrows. When setting the arrows in place, you should make sure that nothing interferes with their movement. Otherwise, you will have to disassemble everything again.If you add the illumination of the scale and arrows to this tuning option, then you can almost instantly transform your own car beyond recognition. Image - Do-it-yourself vaz 2110 interior repair

It's no secret that the VAZ 2110 often has a panel creaking. Eliminating creaking is also called soundproofing.This process begins with the disassembly of the "tidy" into three parts, which are bolted together. Modelin can be used as an “anti-creak”, and Bitoplast will act as a noise absorber.

Modeling should be used at the points of contact between the parts of the panel. All holes from the bolts must be closed with a modelin to eliminate the loss of air flow from the stove. The back of the dashboard must be pasted over with bitoplast.

The rest can be glued inside. This article details how to glue soundproofing. Often squeaks cause a black box with fuses and a glove box. At the bottom of the latter, you need to lay the bitoplast, and the sides should be pasted over with modelin. The sides of the black box that are in contact with the panel should be glued with modelin. It should be noted that the bitoplast is crushed during landing and there should be no problems with installing the “tidy”.

Video (click to play).

Nothing can please the owners so much as silence and the complete absence of various annoying squeaks in the car. The comfort in the cabin, which occurs after the soundproofing of the panel, causes only pleasant sensations.

Rate this article:

Grade 3.2 voters: 85