Do-it-yourself vaz 2110 interior repair

In detail: do-it-yourself repair of a vaz 2110 interior from a real master for the site my.housecope.com.

Leatherette is considered an ideal material for binding door cards VAZ 2101 - 2107, or as it is also called vinyl leather. But if we consider vinyl leather in more detail, then it is much stronger than the familiar leatherette. And when buying, you can stumble upon a wide selection not only among the color, but also among the texture.

When buying vinyl leather, you should pay attention to a very important detail, namely, its ductility, since it is the ductile vinyl leather that can tightly fit all the protrusions of your car. And by the way, it is the viscous vinyl leather that is called automobile leather.

Complete restoration of the entire leather surface, as well as velor and vinyl-leather upholstery of the entire car interior, complete repair of the upholstery.

During the operation of the car, the entire upholstery of our salon suffers greatly. And you must admit it is always unpleasant. A complete replacement is a rather troublesome business, and besides that, it is not cheap, but there is always the opportunity to repair it yourself.

It is quite easy to make an exclusive interior lighting. It is necessary to put a lot of LEDs in the ceiling of the car, then the "Starry Sky" will not only illuminate the entire interior, but also pleasantly amaze your passengers Read more →

The headliner from Priora fits the Auto VAZ 2112 almost perfectly. At the expense of Auto VAZ 2110 and 2111 I can not say, because I have not met any picture or opinions. so let's start talking about the Auto VAZ 2112: Continue reading →

The door trim from Priora is installed in the VAZ2110 without problems, because fit perfectly on the seats. But we need to change the wiring in the front doors, because the ESP (glass lifters) is controlled from the doors, and not from the tunnel between the seats, as in the 10-ke. Continue reading →

Video (click to play).

Here, the usual option "took and put" the Priora torpedo on the VAZ 2110 will not work. there are differences in wiring with both the old dashboard and the euro dashboard with new dashboards.

What the Priora panel looks like in Auto VAZ 2110 is a matter of taste. Someone likes the euro panel, someone a panel from Priora, and still others are generally satisfied with the ancient 10-ki panel Read more →

Often the wife asked why there is no mirror on the sun visor? I think a girl should get into the car already painted, but what if she is used to painting in the passenger seat? Here you cannot do without a mirror in the visor.

In the VAZ 2110 lux, a mirror is installed in the passenger's sun visor, what about the owners of cars with the usual equipment? It is unlikely that it will be possible to buy visors with a mirror for the 2110, but you can simply embed the mirror into the visor. Continue reading →

If you decide to remove the entire torpedo, then follow this photo instruction.

It will be more convenient to put an overlay on the torpedo if it is removed and lies in the house. Remove the standard panel overlay according to the instructions.

Buttons glass of Kalina lifts have a much nicer look and more convenient shape. Therefore, many owners of the VAZ 2110 decide to change the standard ESP keys to Kalinovskie ones. How difficult is it to make this replacement?

There are 2 types of ESP Kalinovski keys: low-current (multiplex) and power.

To supply low-current ESP keys, you will need to supply an electrical package control module / electrical package controller (2170-3763040). Continue reading →

It is believed that fitting a torpedo is not an easy task, the complex shape does not allow the torpedo to be pulled without seams. The visor of the VAZ 2110 torpedo is no exception, which, in addition to its own complex shape, also has a set of keys. Below we will answer the question of how difficult it is to fit a torpedo on our own. Continue reading →

Road safety is linked to driver comfort. Convenience consists of a huge number of factors, including the armrest. The armrests on the doors are designed to comfortably position the hand of the driver or passenger. In this article, we will describe how to enlarge the armrests on the door card. Continue reading →

For a pleasant trip in the car, it is important to keep it clean. It is much more convenient to clean the interior when there are carpets under the feet of the driver and passenger. In this article, we will analyze how to make do-it-yourself car mats.

Ask why to make a rug with your own hands, when you can easily purchase rugs for a car of any brand, if not in the auto market, then you can order it in the online store. Continue reading →

The interior design of our cars has never stood out for its beauty, for example, the old, low panel (torpedo) and a small tunnel between the seats did not provide any convenience. If we talk about the VAZ of the tenth generation, then you can make a better car interior if you put a europanel and modify the tunnel. Continue reading →

Where does the hauling of the cabin begin? Naturally, with the removal of the car seats. It is most convenient to plan the placement of leather and Alcantara fragments on the cover of the banner, when the chair is removed, we sign each part of the standard cover, indicate the name of the material from which we will cut, a simple marker is suitable for this, mark it with a marker on the standard cover.

The frequently asked question is where to buy and how to put your own hands on a euro panel or a torpedo overlay on a VAZ 2110. This is not surprising, the ancient panel of dozens is already tired of and the hunt for how to update the interior. In this article I will show what is needed in order to change the old VAZ 2110 torpedo to the euro and many important points that you will encounter when replacing the old torpedo. Continue reading →

Any car owner who is used to driving behind a tinted car dreams of such a button, when pressed, the tint will disappear, and then reappear as if by magic when the same button is pressed. Continue reading →

All drivers of the VAZ 2110 face a problem - it is difficult to open the glove compartment, especially in winter. In severe frost, you have to use a special tool to open the tight glove compartment. You can solve this problem by lubricating the glove compartment. First, we need to remove it by unscrewing 2 screws. Continue reading →

What can you say about the factory salon for the VAZ 2110 model? It is quite reliable, durable, the internal space is well organized, which has a positive effect on capacity.

But the comfort level here is frankly low. In this regard, many dozen owners decide on a partial or large-scale stage of improving the interior of their car.

Today we will talk about the elements that can be improved, as well as share ideas and give useful recommendations.

In a special table, we will tell you which elements can be replaced in the VAZ 2110 cabin, and what are their features and advantages.

Interior element

Peculiarities

Replacing it has a positive effect on the appearance of the passenger compartment, the level of sound insulation increases if appropriate work is carried out. Plus, you can install more impressive acoustic equipment

Here you can go in different ways - use covers, alter a standard interior, or purchase an entire interior from another car. The choice depends a lot on your budget.

Modifies the interior appearance, provides better information content. You can either modify the standard panel or use panels from other cars

It is not necessary to completely change the pedals, as there are special pads. They look good, provide a more comfortable press

The installation of a new audio system will have little effect on the appearance, but it will seriously affect the sound quality.

The factory steering wheel is not very original and beautiful. It is often changed to new ones, from more recent Lada models or imported cars.

There are many accessories with which you can completely or pointwise change the appearance of the cabin, increase the level of ergonomics and comfort.

If your VAZ 2110 is not designed for the long term, it makes no sense to invest a lot of money in the revision of the interior. If the car stays with you for several years, it is quite possible to improve ergonomics and comfort for yourself.

Now let's talk about some aspects of the interior refinement in more detail.

To change your car door trim, you first need to get rid of the old one. For this:

Unscrew the mounting screws holding the factory trim;
Remove the clip to get the glass lowering handle;
Dismantle the panel where the handle to open the door is held;
Unscrew the lock button;
Pry the trim with a screwdriver and remove it. It is held in place by plastic caps. If you break them, that's okay. Buying new ones is not a problem.

Then proceed at your own discretion. You can purchase a completely ready-made kit, or do it yourself, choose the material you like.

Since you are removing the trim from the doors and are planning to install new acoustics, it will not be superfluous to improve the standard sound insulation by gluing 1-3 layers of sound insulators.

Now let's talk about the upholstery, armchairs, seats. Let's say right away, if you are going to remove the seats to replace the upholstery on them or to install a completely new interior from another car, it is better to take care of the issue of sound insulation. Alas, the factory Shumka for dozens is ineffective, which is why inside the car it becomes very noisy even when driving at low speeds.

Having finished with soundproofing, we decide what to do with the interior.

T-shirts, covers. The most budgetary option that allows you to significantly transform the appearance of the cabin. Installation is easy, does not require special knowledge and skills. But the changes will only be external. The level of comfort for the driver and passengers will not change.

New skin. Not everyone can alter a salon with their own hands. But this does not make the procedure impossible. The bottom line is to remove the old sheathing material and sew a new one instead. In parallel, you can replace the foam in places, slightly modify the design. The option is quite heavy in execution, but it allows you to make, in fact, a completely new interior.

Salon from another car. The level of ergonomics of regular chairs leaves much to be desired. Even replacing the casing and putting in a few pieces of new foam rubber, you will not be able to significantly change the comfort of the fit. A completely different matter is the installation of a completely new salon with comfortable armchairs and a sofa. The downside is the high cost and the search for a suitable salon for dozens of foreign cars. But there is a serious plus - you can transform not only the appearance of the car, but also seriously increase the convenience and comfort. It's worth it if the car stays with you for the next 5 years.

Stylish, modern armchairs

Does it make sense to change the native dashboard to something else? This is where opinions differ. But many note that such a revision is relevant if it is planned to install additional equipment, indicators, sensors on the car. That is, we are talking about fans of not only external, but also technical tuning.

There are several ways to modify the dashboard.

Modify the panel with your own hands, using luminescent paints for arrows, notches, marks on devices. You can also install LEDs, a tachometer, other "chips", cover with a carbon film and so on.
Another option is to buy ready-made inserts that you just need to install. Today, for dozens, their assortment is quite extensive.
Remove the old instrument panel and put in its place a new, more modern one with arrows or electronic type.
Use a dashboard from another car.

Changing the dashboard to equipment from another car, you will have to modify, adjust everything, solve the issue with wiring, connecting sensors, etc. The task is not an easy one, it is better to perform it at specialized car services.

Using all kinds of accessories and tuning elements, you can modify your standard interior without serious investment, distinguish it from the background of other dozen.

Let's talk about some options for accessories.

Pads on the pedals. They are not expensive, but they significantly transform the standard, far from beautiful pedals.

Stickers imitating carbon, metal, wood. They are usually glued to the glove compartment, center console, doors. Such films are cheap, but they seriously change the appearance of the car's interior.

Steering wheel. Using a new steering wheel to replace the old one, you will increase the level of comfort, provide easier driving. You can either completely replace the steering wheel, or alter the old one, make the upholstery of leather or leatherette. The main thing is that the material does not slip in your hands.

LEDs. Lighting elements that can be installed anywhere. They consume a minimum of electricity, so there is no need to fear for a rapidly discharging battery. LEDs are used for interior lighting, pedals, glove compartment, etc.

Rugs. The simplest accessory that has two functions - collecting dirt so that it does not accumulate on the floor, and external decoration.

Electronics. Although the VAZ 2110 is a budget car, no one bothers to modify the interior by installing high-quality navigation equipment, a useful video recorder today, a monitor on the ceiling, modern acoustics, etc.

How LEDs can be used

When installing volatile equipment, take into account that it will affect the battery life, the reliability of the standard wiring. With such modifications, it is better to take care of installing a more powerful battery, as well as replacing wires, the parameters of which are not designed for this level of consumption.

The dozen salon has its own advantages and positive qualities. Therefore, revision is the choice of everyone personally. We have listed the available options for improvement for you, so choose and get to work.Despite the fact that salons that use white material get dirty faster, they look quite attractive. New cars with such a salon cost a lot, but you can replace it yourself in your car, spending not as much time as it might seem at first, and saving money. In this article, we will talk about what elements of the cabin can be upgraded, and the process of replacing the standard cabin will be described.The factory interior of this car is quite reliable, and the space inside is organized quite well. But the VAZ 2110 is unlikely to be able to boast of comfort in front of modern cars, so many of its owners are striving to at least slightly improve its interior.You can improve the following parts:

Replacing door trim to improve appearance and noise insulation.

Replacing the trim of the cabin itself. In this case, you can alter the interior yourself or use the finished interior of another car. It all depends on the wallet of the car owner.

Changes in the dashboard. At the same time, you can significantly expand its functionality, use the panel of another car or upgrade an old one.

Install special pedal pads and replace the gear lever.

Installing a new steering wheel, since the factory one is not original.

The use of various accessories that will affect the appearance of the interior and make it more comfortable and ergonomic.

Parsing the cabin will not be difficult and will take no more than 3 hours, even for a person without experience.First, you need to pull out the car seats so that they do not interfere with the work, then gradually remove the entire interior trim without damaging the panel wiring. There are a lot of wires here, so it is imperative to mark each connector so as not to confuse when reinstalling.The wiring must also be removed and inspected for cracks, traces of corrosion or burnout in the factory winding. In most cases, after a long period of use, the car's wiring needs to be replaced.To do this, perform the following actions:

Get acquainted with the car electrical equipment diagram;

Remove the front panel of the passenger compartment;

Carefully inspect the wiring, especially those wires that are connected to the mechanism of the windshield wipers and headlights of the front group.

Dismantle damaged wiring and replace it with a new one.

The first step is to dismantle the factory upholstery. This must be done carefully and in approximately the following sequence:

Using a screwdriver, unscrew the screws that hold the factory upholstery.

Remove the handle for lowering / raising the door glass, for which you need to first remove the lock.

Remove the panel holding the door handle.

Unscrew the door lock button.

Use a screwdriver to lightly pick up the upholstery and carefully remove it. Plastic caps are used to secure it. They can be broken when the skin is removed, but this is not a problem - you can buy new ones in the store.

In terms of the need to rework the factory dashboard, opinions differ: someone is satisfied with the existing one, others want to alter it a little in order to install additional sensors, indicators and other elements.Methods for finalizing the dashboard:

It is possible to upgrade the devices themselves using luminescent paint, which is applied to the arrows and markings on the devices. If desired, you can add a tachometer, install LED bulbs, etc.

Purchase ready-made inserts, the assortment of which is quite large.

Replace all devices completely with more modern ones, with arrows or an electronic display.

If the panel of another car is available, apply it. In this case, there may be problems with the wiring, fitting the panel case. Therefore, it is not recommended to do this on your own without experience.

As a material, you can choose an inexpensive leatherette. It is easy to handle, cut out pieces of the desired shape, and glue. However, it also has some disadvantages:

Poorly resists mechanical stress;

Wears out faster than genuine leather.

Poorly tolerates temperature changes.

But leatherette is much cheaper than leather, so it was decided to choose it as the main material for the new salon.For a new cladding, you will need about 4x2 meters of fabric (it is better to take with a margin), out spirit, glue 152I, a large supply of patience, since the work is rather painstaking. The best option would be special glue 88, which can be purchased at a specialty store, but the glue mentioned above also coped with its task.All work is best done in an open space or in a garage. The glue is quite toxic and has an unpleasant odor, which is very difficult to get rid of if you work right in the apartment.A clerical knife and scissors were used to cut the material along the contour. Use scissors to cut a rectangle, which is then attached to the panel. Trimming can be done with a clerical knife along the contours of the panel, while leaving a margin. The glue must be applied both to the panel itself and to the surface of the cloth mating with it, and wait 10 minutes. After the glue has dried, apply the cloth to the panel and gently smooth it out so that there are no wrinkles. It is advisable to perform this procedure the first time. If you did not succeed in gluing evenly right away, you will have to tear off the leatherette pad, on the surface of which glue can appear.It is much easier to glue the smaller parts of the panel with a leather substitute, so special attention should be paid to the large parts.The configuration of the main panel is rather complicated, so it is unlikely that it will be possible to cut a whole piece of leatherette according to its shape. It is best to divide it into parts, marking it out with a pencil:

The left side of the panel to the console, near which draw a line with a pencil;

Directly the console;

The right side of the panel, which has a glove compartment.

After gluing the material, it is necessary to collect all the panel elements and visually check if everything turned out correctly.Now it is necessary to glue with Madeleine all the joints and interfaces of the plastic elements of the panel, using a sealant to grease the air ducts, since they have rather large gaps. The inside of the panel can be splenished with a thickness of 4 mm.From the door trim, which was discussed above, it is necessary to remove the top layer of the factory material. This is necessary in order for the leather substitute to adhere better. Similar to how the leatherette was glued to the panel, it is necessary to cut the material along the contour, grease the mating surfaces with glue, wait 10 minutes and carefully combine them. Optionally, you can also glue a neon-lit cord around the door handle. So it will be more noticeable in the dark, and the door will look even more attractive.Similarly, it is necessary to glue the upholstery of each door.First of all, it is necessary to dismantle all the remaining interior elements, thoroughly clean and wash everything.Vibration-absorbing bituminous material must be installed on doors, ceiling, motor shield, floor tunnel and arches and other surfaces. You can use Visomat MP 4. It is also possible to dismantle the rubber plugs that cover the technological holes in the bottom of the car. In their place, it is better to install a Visomat, while doing this both from the side of the cabin and the bottom.Spleen 10 mm was used as noise insulation, and a factory noise isolator can be laid on top.Before installing the panel, it is necessary to connect all the wiring and check its functionality, since re-removing and installing the panel is a rather difficult process.Next, you need to reinstall the panel. Difficulty can arise if too much soundproofing material has been used, the excess of which must be removed. It is also quite difficult to install the panel in the guide pins that are located in the area of the oven.You can install plastic pipes in the air duct for supplying air to the legs and close the cracks with polyurethane foam. It may not look very aesthetically pleasing, but your feet will be warm.A GPS navigator can be installed in the center deflector. To do this, you need to remove all the jumpers, cut the opening a little. For installation, you will need epoxy resin, fiberglass, putty and primer.The seat upholstery can be made by yourself or ordered from the vehicle manufacturer. If you decided to customize the seats yourself, you can choose one of the following options:

Install new shirts and covers. The new elements will only visually change the interior, but will not affect the comfort of the driver and passengers.

You can make the cladding with your own hands, which may not work for everyone. After removing the old material, it is advisable to replace the old worn out foam rubber.

Install seats from another vehicle. But it is rather difficult to find suitable for the VAZ 2110.

To make your tunnel, you will need a sheet of plywood 4 mm thick and sheets of cardboard to create templates.The first step is to install the bottom of the factory tunnel. Then, using sheets of cardboard, make templates according to which a tunnel is cut out of plywood. On the resulting tunnel, you need to glue the leatherette material and screw the resulting product to the factory tunnel.The simplest, but at the same time inexpensive and effective way is to overexposure using single diodes and a diode strip. You can choose any color you like. The main thing to remember is that the dashboard will be in front of your eyes all the time while you are driving. And too bright, catchy colors can significantly increase fatigue and annoy the driver.Also, the backlight can be matched to the color of the car. Both in tone and in a contrasting shade. In addition, external lighting is often done, then it is important that the colors must be combined. Therefore, if you plan to do tuning not only in the salon, be sure to decide in advance in what colors and what. So that in the end the car looks holistic and harmonious. If this is not done, you can achieve the effect of a Christmas tree. And instead of stylish tuning get a "collective farm" version.As a rule, backlighting is done on the following parts of the panel:

the panel itself along the edge;

clock;

oven damper regulator.

The interior and body can, and sometimes it is necessary, to highlight in the following places:

install separate lighting for the rear seats, which will not intersect in the direction of the common interior lamp. This is necessary both for small children who are afraid to ride in the dark, and just for passengers who, suddenly, need light on the go. After all, such a backlight does not interfere with the driver at all. By the way, that's why it is also worth choosing soft, not too bright diodes for it;

illuminated glove compartment, both inside and outside, it is not only very convenient, but also very beautiful, bright and stylish;

the backlight looks good in the legs, both for the passenger and the driver;

of course, a bright light in the trunk, this is an extremely necessary, important and truly rational addition to the standard car lighting;

duplicating the highlighting of the room is also a very worthwhile addition;

backlighting with diodes instead of running lights is currently very popular, both due to its economy and for its stylish and bright appearance.

Thus, it is a great idea to make tuning a car using backlighting both with single diodes and with strips of them. And most importantly, it is accessible to almost every car enthusiast. After all, the materials will require a very modest investment. And the installation of their any complex and rare skills will not require.But all the same, if you have no real experience with a soldering iron and LEDs, it is better to find a master or just a friend who knows how to handle all of the above. And ask him to help with the installation and installation at least at first. And then, when your own skill appears, continue editing yourself.This section is devoted to tuning a VAZ 2110 car with your own hands. You will find a lot of interesting information on tuning your VAZ car. All articles were written by the real owners of the VAZ 2110 and were applied in practice.Probably every owner of a VAZ 2110 car, sooner or later, is faced with such a task as the need to replace the timing belt, or in abbreviated timing. The timing belt must be changed every 45 - 50 thousand vehicle mileage.A car generator is a device that generates current to keep the electrical devices in a car running continuously. Battery charging, vehicle voltage, etc. depend on this device. It is very important to know which generator is best to choose for the VAZ 2110 - 12?The cabin filter removes exhaust gases and dust from the air entering the cabin. We can say that the cabin filter protects the human respiratory system. The cabin filter, series of the tenth VAZ family, is located after the air intake, but in front of the heater.The main task of any filters in your car is to prevent dust from entering the engine or car interior. The fuel filter cleans gasoline; air - air supplied to the carburetor (injector); oil - oil in the engine.It is best to change filters on time so that later you do not have to spend extra money for repairing your car.If you do not have a fan that cools the car's radiator, the cause of this may be the coolant sensor. It is this sensor that is responsible for cooling the car's radiator. I want to say that if you find such a problem in yourself, do not rush to change this sensor. Don't waste extra money. It would be best to test it for performance.At the initial stage of reworking your own car, much attention should be paid to tuning the VAZ 2110 panel. Many owners of the "dozen" adhere to the position that their car should not lag behind modern fashion trends in the world of four-wheeled high-speed "iron horses".Of course, everyone wants his car, despite a certain wear and tear and the already rather rich history of the VAZ 2110 brand, to look beautiful, "feel" powerfully and provide high comfort inside the cabin for all passengers. In the process of moving in a vehicle, many passengers pay attention to the devices.Of course, always more interesting for them will be original devices with exclusive design solutions that literally amaze and delight. Tuning the VAZ 2110 instrument panel should begin with a search for panels. To establish such a detail, you will have to use your own skills and dexterity, if you do not want to give your hard-earned money in various car dealerships.Moreover, this work does not require the use of special tools. It will be enough to use pliers and a Phillips screwdriver.The whole process of updating the dashboard with your own hands does not take much time. All that needs to be done is to dismantle the obsolete "part" and install the modernized model. How to remove the VAZ panel, you can find out here and in the manual for the repair and operation of the car. But the main steps should be recalled:

first you need to disconnect the battery terminals. The steering wheel should be lowered to the lower position.

it is necessary to unscrew the self-tapping screws of the panel overlay.

then we disconnect the connector on the left, in this situation we are talking about the machine switch for external refresh. Then, using pliers, you should unbend the fixtures of the instrument cluster.

Next, we remove it. Some models are fixed with M5 screws. Finally, disconnect the connectors.

After that, you can install the new panel in the reverse order. Such tuning of the VAZ 2110 with your own hands will always arouse admiration among passengers and a sense of their own pride.Today the fashion of changing the dashboard illumination is gaining fantastic momentum. Almost everywhere, cars have neon lights or interior LED lighting. However, all these innovations are not cheap pleasure that not everyone can afford. The situation is different with the replacement of the factory backlight with a multi-colored one.You can, no doubt, use ready-made tuning options, but it will cost a lot. It is best to do it yourself. In this situation, the main thing is to have the necessary materials and patience. First you have to disassemble the "tidy". It is necessary to remove the protective glass. Next, remove the arrows. To do this, you need to use a screwdriver and hard cardboard.It should be placed under the arrow, and then pry it off with a screwdriver. Then gently and slowly raise it to the top. Next, remove the backing. A clerical knife is useful for this. It must be inserted between the panel and the substrate and a layer of sealant cut through in a circle. Then we remove the backing. We disassemble the panel and start.1. Remove the filter layer using a clerical knife. A light filter is a colored layer of paint. It is applied from the back of the substrate and gives color illumination to the speedometer numbers and the rest of the gauges. To get rid of the filter completely, you can use acetone or another liquid that contains alcohol.2.Next, change the highlight color. The odometer backlight can be changed first. To do this, you need to dismantle the odometer screen, and then remove the blue film and remove the backlight bulb. It should be replaced with a multi-color universal LED. He can change colors. We attach the LED to the standard bulb holder. Reinstall the odometer screen.3. Now you can start completely replacing the backlight. We attach the LEDs to the tidy frame. These LEDs can be purchased with a color switch. We install them in place and attach them to the standard contacts of the backlight of the device. Image - DIY VAZ 2110 interior repair

4. Let's go further. Now you need to make sure that the arrows have the ability to change the highlight. To do this, remove the layer of red paint from the arrows. For this operation, you can use a clerical knife and acetone. When the arrow is cleaned, it can be painted using white nail polish. The main thing is that the arrow is white, since this color reflects the color gamut of the LEDs.

5. Before the final step, you need to fix the LED color switch on the panel. Such a switch can be installed, for example, in the lower right corner of the "tidy". Then you can put everything in place. First, the substrate is mounted. For greater reliability, you can use a sealant. After that, we put the arrows in place. We insert the protective glass. After that we admire the result.

Tuning the panel of the presented car, among other things, you can also beautifully highlight the "tidy" buttons. Take the rear fog light button, for example. First you have to dismantle and disassemble it. To do this, pull its moving part and body in different directions.

After the button is pulled out, the incandescent lamp can be accessed. If you wish, you can take it out. If it is not possible to pull out the light bulb, then follow on. Using a screwdriver or a knife, we pry the latches on both sides. A switch mechanism will appear in front of us. We need a black brace here. Prying it off, we will calmly scatter the whole mechanism.

Now we can easily remove the lamp; tweezers are suitable for this. Now you can connect your fantasy. You can purchase an LED lamp in any color. It should be borne in mind that the positive contact is # 6, and the negative contact is # 7. You can tell the polarity by looking at the back of the case. A block with wires is inserted here. Next, let's check how the backlight works. If everything is ok, move on to the next part.

Get rid of the green filter. It can be drilled out, this must be done carefully so that the drill does not go through the entire structure. As a result, we remove the light filter from the structure and check it for operability.

It should be noted that almost all buttons, if desired, can be modified in this way. The only exception is the position of the negative and positive contacts, they must be looked at in the wiring diagram. If there is no diagram, you can safely find a photo of it on the Internet. The negative contact is usually denoted with a black wire, the positive one - of any color.

Most often it is white. You can remember, but it is better to sketch or photograph the contact connections, then there will be no confusion during the assembly process. The assembly process must be carried out in the reverse order.

You can nicely complement the panel by installing a tweeter (tweeter). Drilling holes is one of the most challenging steps. The windshield interferes with right angle drilling. But it is impossible to do without a drill, because there is a metal strip under the plastic shell. In this situation, a semblance of a template or stencil should be made from paper.

Using a knife, you can remove the soft area of the panel (from the outside - plastic, from the inside - a kind of foam rubber). Then we take a drill and drill around the previously marked area. It is better to use compact drills.When the hole is drilled, the uneven edges should be corrected. To do this, you can use special drill bits.

You need to drill away from instruments and sensors. Please note that wires or brackets can be caught under the metal strip. The tweeter element to be mounted must fit snugly into the hole. If there is some freedom, then it is necessary to seal this area with a sealant. The tweeter wires can be hooked around the edges of the ductwork.

This tweeter is an important component if a speaker system is to be built in a car. Without such detail, the sound and sound volume will not be complete.

Domestic car 2110 cannot boast of a high-quality panel. In severe frost or summer heat, plastic often begins to crack. In addition, its corner sometimes peels off. The "tidy" of this machine consists of three parts: a central, upper lining and a lower plastic lining. The corner is most often peeled off through: unscrewing the self-tapping screws that attract the upper plate, or through the fact that its soft part has moved away from the metal part of the upper plate.

In the first option, you need to remove the panel, because otherwise you will not be able to tighten the top cover. If only the soft part has departed, then there may be several solutions. You can glue it, but it won't hold on tightly, on a plastic air deflector. Another option is to mask the gap that forms when the corner of the panel comes off.

You can, no doubt, cover the gap with a wire. It is laid inside using a screwdriver. Instead of a wire, you can use a headlight seal. In this case, you can return the corner to its place. Polyurethane foam is used to glue the corner. The casing, thanks to the foam, will adhere precisely to the metal body, but first it must be cleaned and degreased.

Then we apply the foam inside, remove the excess foam with a wet rag. Press the corners with paper clips. You do not need to immediately remove the foam. Wait until it dries. After the foam dries, you need to paint over it with a marker. It may seem like the foam is bursting, but in reality, the corners of the panel will not come out.

Now you can proceed to repair the cracks on the panel. To do this, use either a tool for repairing plastic, or overtighten the lining with material. As for the first option, it is the simplest, because you do not need to remove the cover during repairs. You can remove the crack using a special epoxy resin.

Cosmophene and cold welding are also suitable for use. To prevent the crack from standing out, the dashboard should be repainted. In the second method, when tightening this car part, leather or leather is used. First, the crack must be filled. If the problem is in the corner of the panel that has come off, then it will not be difficult to repair it.

If the "tidy" is cracked, then it is very difficult to completely hide the crack and, at the same time, not to remove it. If the matter concerns the repair, then it is better to immediately replace it with a Euro plate. Here you can see in detail how to solder plastic.

The boring standard panel (in the video) quickly bores many owners of the VAZ 2110, but I don't want to buy an alternative one, which is equipped with a computer and costs a lot of money. What to do in such a situation? There is a great option that will allow you to carry out economical tuning with your own hands. One of the easiest ways is to buy an overlay.You can find them without any problems in online stores (the photos presented there give a general idea of such details). To install it, you need to remove the "tidy" and carefully pull out the arrows. When installing the arrows in place, you should make sure that nothing interferes with their movement. Otherwise, you will have to disassemble everything again.If you add the illumination of the scale and arrows to this tuning option, you can almost instantly transform your own car beyond recognition. Image - DIY VAZ 2110 interior repair

It's not a secret for anyone that the panel of a VAZ 2110 often creaks.Eliminating squeak is also called soundproofing. This process begins with disassembling the "tidy" into three parts, which are fastened together with bolts. Modelin can be used as an “antiskrip”, and Bitoplast will act as a noise absorber.

A modelin should be used in the places where the panel parts touch. All holes from the bolts must be closed with modelin in order to eliminate the loss of air flow in the stove. The back of the dashboard needs to be pasted over with bitoplast.

The rest of it can be glued inside. In this article, in more detail how to glue sound insulation. Often squeaks are caused by a black fuse box and glove compartment. Bitoplast should be laid at the bottom of the latter, and the sides should be pasted over with modelin. The sides of the black box that are in contact with the panel should be glued with modelin. It should be noted that the bitoplast is crushed during landing and there should be no problems with the installation of the "tidy".

Video (click to play).

Nothing can please the owners so much as the silence and the complete absence of various annoying squeaks in the car. The comfort in the cabin, which arises after the soundproofing of the panel, causes only pleasant sensations.

Rate the article:

Grade 3.2 who voted: 85