Smoking in the car is not the best idea, but sometimes it is difficult to resist this addiction.
Firstly, smoking in a car is simply dangerous because it is distracting, a person relaxes, acrid cigarette smoke can get into the eyes and at a critical moment a cigarette can lead to disastrous consequences. The second unpleasant moment is the side effects of the well-known addiction - not a very pleasant residual smell of tobacco in the car, ashes lying everywhere and, the most unpleasant, burnt places.
An ember of tobacco can fall on the seat upholstery, you can accidentally wave your hand and put out a cigarette on the front pillar, some especially lucky comrades even burn through the ceiling!
What to do in this case? After all, a burnt seat is not at all aesthetically pleasing. For many people, the interior of a car is a kind of calling card. In addition to the appearance of the car, the second thing that almost any person draws on is the well-groomed interior of the car.
The burnt hole must be sealed. There are three ways. The first - high-quality, but costly - will turn to specialized services offering services for restoring the original appearance of a car.
The second, less expensive, but much more difficult, is to purchase an upholstery repair kit.
This path is different in that with a probability of 80% it will send you to a car service to professionals. Without certain skills, it will not be easy to make high-quality repairs on your own with the help of.
Fortunately, there is a third option. It will require only accuracy, a minimum set of tools that you can find at home and a minimum of time. However, the result will pleasantly surprise you!
In an inconspicuous place, for example, at the bottom of the seat, taking a razor, shave off the required amount of upholstery fibers.
Collect the fibers in a small container. The fibers of the upholstery material will look like plain fluff.
Using tweezers, sketch the extracted material onto the glue. Don't tamp it down!
Re-apply a thin layer of adhesive over the fibers. Careful! Avoid hitting undamaged areas.
Using tweezers, put in some more fibers until the hole is completely filled with them.
Take a piece of any dense fabric. We will use it as a substrate. Cut out a rectangular patch. Round off the edges. This will make it easier to push it into the hole and straighten it under the upholstery.
We take fabric glue and a needle. We apply glue to the needle and process the patch as shown in the video (43 seconds). Carefully apply glue so that the scarf does not move from its place.
Apply glue to the resulting substrate. You can also use an external patch, as shown in the video. It doesn't change the essence.
The most important moment. Gluing a piece of fabric to the upholstery of the seat. Where can I get patch material? It can usually be cut from the bottom of the seat.
For a quality repair, it is very important that the pattern of the outer patch matches the overall pattern of the seat. Here you have to measure seven times, cut once. You will succeed, we believe in you!
We press the delivered scarf. We are waiting for a couple of minutes.
The network of auto repair shops "Avtoscratch" performs repairs of burns in the car interior using high-quality materials.A flexible system of discounts and bonuses makes the prices for services even more affordable. For your convenience, our service stations operate in different areas of Moscow and St. Petersburg. We undertake the repair of burns in the upholstery of the ceiling, seats and other surfaces of the car interior. Masters will do everything necessary to remove the damage without a trace.
VIDEO
Even a short contact with a hot object does not leave a trace for the upholstery. In addition, such damage, if not repaired in time, can grow as the car is used. The salon is falling into disrepair faster and faster. The car loses its presentation and ceases to be a pleasure to travel.
If you or one of your passengers burns a car seat with a cigarette, it can turn out to be very expensive. If you leave the defect without attention, then over time you will have to pay for the upholstery of the cabin or the manufacture of covers. To prevent this from happening, you can contact the Autoscratch company. Our experts quickly and very carefully restore damaged areas of the cabin after burning.
Technical centers located in Moscow and St. Petersburg are equipped with everything necessary to repair car seat burns. The guarantee of a high level of service is:
the use of high-quality degreasing, adhesive, coloring compounds;
professional tools for stripping, gluing, heat treatment, full restoration of upholstery. The repair of burnt seats is carried out in such a way as to restore the aesthetics of the damaged area and make it strong enough. All work is carried out manually;
masters with extensive experience in eliminating burns in the seats of SUVs, minivans, minibuses, cars of different brands;
exceptionally careful and delicate handling of vehicles left with us;
attractive prices, discounts.
To get advice on eliminating burns in seats of other parts of the car interior, order a free call or call us at: 8 (800) 301-31-43.
The authorities began an uncompromising fight against smokers. The editors of the GAI magazine turned out to be much more tolerant. In our opinion, a car is not only a means of transportation. A car, as a rule, is also a place of our freedom, where we can indulge in vicious passions to the fullest: listen to your favorite music at full volume, chat with friends and girlfriends without extra ears, smoke a cigarette, and everything else ... Therefore, we decided to fight not with smoking, but with its consequences. The technology of resuscitation of upholstery burnt by a cigarette in one of the car wash complexes of the city was mastered by Olga Medvedeva, sales director of the GAI magazine.
Break before work
This lesson turned out to be the most unusual of all that we have ever been given. Firstly, the co-founder of the car wash complex, Semyon Syskov, who personally led the process, gave me maximum freedom of action. Secondly, at all stages of training, he gave extremely positive assessments, accompanying my actions with the words “excellent”, “excellent result”, “I like it”. He also allowed experimentation, convinced that any technology gives only a general theory, and every master has the right to look for suitable methods of work. And even though the experiment was unsuccessful, it did not affect the final result. Looking ahead, I’ll say that such a pedagogical approach seemed ideal to me: the first time I managed to close up the procuration so that there was no trace of it. All that remained was a great mood in which I stayed until the end of the working day. Yes, and this lesson began unusually.
Hello, are there any smokers? Bring a cigarette and a lighter, - Semyon met us, stroking the gray headrest, which he had prepared in advance for work.“We’ll have a smoke before work, and at the same time we’ll burn through the upholstery, which we will fight against. Quite often, in cars, the headrests and seats are burned through.
The headrest was “working material” taken from an old car, so I dealt with it ruthlessly. In fact, non-combustible materials are used in cars: they ignite poorly, but melt well. Boldly brushing off the ashes, I made a decent and rather deep hole in the headrest.
For our city (and I think for Russia too), the technology of resuscitation of burns is a relatively new service, although in the West it has existed for a long time. Maybe that's why a special set for this operation, including colored microfiber, pencils, scissors, tweezers, spatula, iron, spray gun, liquid and powder glue, has to be bought abroad. The domestic auto industry has nothing to be proud of yet: the production of such art sets for motorists has not yet been established in the country.
The clock was 11:05. We recorded the time in order to know the timing of the procedure, and set to work.
My arts
First of all, I sand the edges of the hole. Then I carefully cut the edge with nail scissors.
After that, I lift the edges of the fabric with tweezers to put the patch under them. I also take the material for it from the “magic suitcase”. I cut out a small square and with the help of tweezers I put it under the edges of the upholstery to close the hole.
“There is nothing difficult in patching holes,” Semyon observes the work. - Here anyone can handle it, any procuration, in principle, can be repaired by yourself, if there were pens and a desire. This is where the work of the jeweler and the seamstress ends, we begin the work of the colorist.
I take jars of sheared microfiber out of my suitcase to match the color of the headrest material. There are dozens of shades and colors of them, but there is no ready-made one. So I start looking for the right one. I take a gray close to the main one as a basis and put the villi into a glass jar with tweezers. I add a little dark gray to it, then some more black. I close the jar and mix with a spray bottle. The color turned out close, but something is missing in it.
“There is a little bit of blue in the native fabric, if we add a bit of gray with a bluish tinge, it will be just right,” Semyon unobtrusively suggests, but does not touch the jars himself. Today I am given full independence.
All this is reminiscent of the work of a master in the selection of car enamel - once I already mastered this profession. By the way, professional colorists do just that in the car wash complex. Only with computerized paint selection, specially designed color formulas are used, the paint is added by the gram, and here you have to mix everything by eye.
But my eyes didn't seem to let me down. I pour the mixture onto a plastic tray, still add liquid glue by eye in a ratio of 70 to 30, mix until smooth and spread the mixture on a patch. And only then it becomes clear that I made two mistakes. First, after adding the glue, the mixture became lighter than the main fabric of the upholstery. I also saved money - I didn’t have material left for the second layer, which is prepared from a mixture of sheared pile and powdered glue.
Repetition is the mother of learning
- So, I'll have to do color again and make another portion. Don't worry, repetition is the mother of learning. While according to the technology the first layer will dry for 15 minutes, we will just do everything.
Again I start mixing the villi. Taking into account the errors, I add more dark color. Of course, I am not a professional colorist who finds the right combination at the moment. But soon another portion is ready. It must be thoroughly mixed with powder glue in the same proportion. There are subtleties here.If you overdo it with glue, the surface will begin to shine, if you do not report it, it will not hold well.
The villi do not mix well with the powder, and Semyon and I decide to move away from technology and experiment: I put everything in a jar and mix it with a spray bottle. But the experiment failed: it turns out that the powder glue settles on the glass. Therefore, I add a little more glue, mix it with a spatula and spread it in an even layer on the place of procuration. I take an iron heated to 170 degrees, which needs to “smooth out” the surface, but Semyon stops. It turns out that on top of the second layer, you still need to spray a clean mixture of microfiber without glue.
Finally, through a special fabric, I iron the place of procuration. There are also secrets here - how many times and for how many seconds you need to hold the iron, but let this remain my little secret.
When everything was ready, I already called to assess the quality of the work of the main critic - our photographer, a graduate of the art school and the architectural institute. But then it turned out that under the iron the mixture thickened and settled. Therefore, I had to repeat this procedure again. Ready. I hit the color perfectly. But the place of procuration is a little shiny.
Did you change Clay?
The clock was 12:05. The entire procedure for resuscitation of the headrest, which now looked like new, took exactly an hour, along with the correction of errors. Fast and efficient.
The material was prepared by the GAI magazine.
During operation, not only the technical parts and mechanisms of the car wear out. It also exhausts its resource and the interior of the car. Like any part, the interior of the car experiences some loads associated with the driver, passengers, transportation of various goods, which can not only cause a mechanical defect, but often simply pollute the interior, from which the upholstery also deteriorates.
Restoring damaged upholstery is within the power of almost everyone
Almost any car owner, and even more so car enthusiasts, will obviously be upset by the appearance of any damage in the interior of their favorite car. The defect will constantly be evident, as a result of which the owner will experience discomfort, passengers will begin to ask questions that remind of wear and tear. And in the case of selling a car, the buyer will have a significant opportunity to reduce the price and will be right in some way, which will not please the seller in any way.
There are several ways to solve the current problem. The first method is the easiest, but also the most expensive. In this case, the owner will have to give his vehicle to a workshop for the repair and upholstery of the car interior. In this case, you will have to pay for materials that are sold with a wrap, as well as the work of a master, which can turn out to be a tidy sum.
How much is the life of the car and how to increase it - find out here.
Also here you will learn about what to do if the car engine is very hot.
The second way is self-repair. All that is required in this case is materials, tools and the main condition for success is accuracy and care. Before starting repairs, it is worthwhile to immediately assess the severity of the defect, as well as assess the condition of the interior as a whole, because is it worth repairing one small hole when the entire interior is in a deplorable state.
If the owner cares about cleanliness and tidiness, and yet the repair makes sense, then the following procedures must be performed:
First you need to deal with the material of the upholstery. If you use leather, then it is not so easy to burn it, there will be no hole, but a trace may remain, which can be cleaned at the sink or dry cleaning.If the usual fabric or velor, then the situation is more complicated. First of all, you will need to clean the entire interior from dirt and dust. This procedure can be carried out independently, if you do not want, then you can go to the sink, where everything will be done for you. Why is it so important to wash everything first? This is due to the fact that you will need to see the color of the interior, and the place of the patched hole, and it is desirable that the color does not diverge.
Estimate the size of the hole, based on the size, we will understand how much material will have to be obtained, and how difficult the repair procedure will be.
When you have decided on the size, you need to carefully cut off the burnt thread around the perimeter of the hole. Accuracy and confidence in movements are very important here. Too much cutting is not necessary, this will once again increase the diameter of the hole. It is necessary to cut off only the burnt part. This step is done so that after the repair, the patched hole does not continue to cling to anything, which can cause a hole to form again in the old place.
This step is optional, but if you suddenly do not have time to finish the repair, or there are no materials, then carefully sew the hole with a thread and a needle to avoid further growth in the diameter of the flaw. Or this way of solving the problem is also suitable for those who do not make sense to restore one hole, because the interior is in poor condition. And to patch it up, so the hole will also be useful, at least now nothing will cling to the burnt tissue, and in which case the further development of the hole will be stopped.
In the case of buying fabric, you need to choose a very accurate new fabric in terms of composition and color, if it is possible to make such an acquisition, then excellent. If not, then you will have to extract the material and fibers of the fabric with your own hands. To do this, you need a fairly sharp tool, old machine razors, or straight razors are ideal here. After you have acquired a cutting tool, you need to carefully collect the fibers of the fabric, this is done on an inconspicuous part of the seat somewhere below, the main thing to remember is not to cut the fabric, but simply collect small threads, that is, the structure itself.
If you have temporarily sewn up your defect, then it's time to open it. Next, we take the usual fabric of a simple color, either white or black does not play a role here. We also purchase special glue for joining fabrics. It can be purchased at textile stores. And we glue our extracted fabric to the upholstery of the car interior from the inside of the hole. Filling the entire chair with glue is not worth it, it can ruin all the efforts, you need to glue strictly the part where the hole is. You need to glue it carefully, perhaps once will not be enough, then you will have to repeat the procedure. Now it remains to wait for everything to dry.
Now you need to cut off a piece of the purchased fabric, or collect all the fibers extracted earlier. Then fill our hole and the fabric glued to it from the inside with the same glue. Then carefully insert a new cloth, or use fibers to fill the hole. In the case of using the extracted material, it is necessary to fill in all the problems so that the glued fabric would not be visible. Then we wait until everything dries up, and repeat the procedures again, only if we used fiber from the cabin.
In general, the burn repair can be considered complete. This method of eliminating the “burn” is suitable not only for restoring seats, but also for eliminating cuts and holes in the car ceiling, door cards and various elements treated with fabric. The procedure itself is simple, such manipulations can be performed by every neat and attentive person.
There are many more ways to rehabilitate the appearance of the salon, but perhaps they will be more difficult. Such methods include using more special glue or mortar, as well as using paint, the tone of which will have to suffer in order to match the main color.Such methods are more used by professionals, so it is better that they repair the flaws in this way.
Repairing a burned-out car seat is not a particularly difficult task. Make it possible for almost everyone.
VIDEO
As you can see, everything is quite simple. If you care about your car, then this article will be very useful to you. Using the tips above, you can easily eliminate some minor defects without resorting to the help of specialists on your own. Also, after the repair, if you want to additionally maintain the condition of your interior, you can purchase special covers for your seats, this will additionally protect them from outside influences, which will prolong their life and good condition.
Today, the car has ceased to be just a means of transportation and has become perhaps the only place where we can feel complete freedom: listen to your favorite music at full volume, chat with friends without witnesses, calmly smoke a cigarette without fear of being fined for smoking in a public place. But as they say, you have to pay for pleasure and retribution overtakes us in the form of burnt seats. Therefore, in this article, we decided to share a method for restoring the upholstery of the interior seats with our own hands.
Repair burns on car seats
For this purpose, we need a special kit, otherwise called a repair kit, however, in Russia, restoring seat upholstery using a local method is not yet very common. Such a procedure can most likely be ordered in specialized workshops, but if you want to do the repair yourself, then you will most likely have to order a repair kit from abroad. The local skin repair kit includes the following items:
- colored, sheared microfiber imitating pile;
Work description
- we clean the edges of the burn with a fine sandpaper, then carefully and slowly cut the edge around it with miniature scissors from the set;
- then we lift the edges of the fabric around the burn with tweezers so that you can put a special patch under them from the material included in the kit (we cut out a patch of the required size and place it under the edges of the burn with tweezers);
Jewelry work is over, now it's time for coloring. In our case, the burn is on the velor upholstery, so we need the sheared microfiber that is in the kit, in different jars and has different colors.
We select microfiber that matches the color of the surface to be repaired, if the desired color is not in the set, we try to get it by mixing the villi of different shades, but so that the color of the villi is a little darker, because after adding glue the mixture will become a little lighter.
The next step is to add special glue to the microfiber villi. We do all this on a special tray. The proportion is approximately 70 to 30. We mix everything with a spatula until a homogeneous mass is obtained and spread this mass on the prepared patch in an even layer.
Tip: try not to violate the proportions, because if there is more than the required amount of glue, the restored surface will shine and shine, but if there is not enough glue, the composition will not hold well.
We heat the iron to a temperature of 170 degrees, sprinkle the burn with clean microfiber without glue, lay a special fabric from the set on top and iron our structure through it with an iron for several seconds.
After heat treatment, the repair mixture may sag somewhat, therefore, if necessary, the entire procedure described above should be repeated. At the end of the work, we leave everything to dry for several hours, after which we will treat this place with a special protective spray from the kit and go over it with a slightly special brush.
The burn repair work is over, the result is beyond praise.
VIDEO
Hurry up, stock is limited, call:
Leader Car has been restoring seat upholstery for over 15 years. We use high-quality modern equipment, so we can guarantee you a quality service. Restoration of burnt seats from 500 rubles.
Our company offers a service for the repair of seats and car interiors. Car seats are subjected to a lot of stress and at any time can be spoiled by a cigarette, or stained with food or drinks. Of course, it is best to alter the seats, but it is often much cheaper to fix a local defect, this will help save money. We can reupholster dented seats or fix holes in the upholstery. The cost of repairs depends on the amount of work required.
Saving time. Seats can be repaired in a matter of days or even hours, while waiting for new seats or covers can take more than a week.
Financial savings. When repairing upholstery, you can not replace the entire coating, but only its individual segments. At the same time, neither the quality nor the type of upholstery material after restoration is inferior to the original counterpart, and the repair itself is several times cheaper than a new purchase.
You can order a car seat repair service in our company. Our masters will quickly and efficiently repair any damage to the seats of your car at quite reasonable prices.
Car MINI COOPER S. Ceiling burn-through repair.
The interior repair time with color matching is 30 minutes.
The repair time for a ceiling burn-through in a car with an already selected color is 15 minutes.
Leather goods repair. We can also do this:
What can a kitten do with a boot.
And we can do it. After the restoration of the skin and painting. Works on the repair of leather products are carried out in the center on Paveletskaya.
Seizure of the vinyl upholstery of the seat in the car.
Car seat repair in the center on Paveletskaya. Sealing, texture and painting. Here is the result. Repair time 1 hour.
The time spent on local repair of such damage was about 60 minutes.
We carry out express repair of leather, vinyl, plastic, velor
The AvtoTOTEMM company carries out exit repair in the territory of the customer.
“Liquid glass” Gzox, Hi-Mohs coating on a Rolls Royce car in AutoTOTEMM
VIDEO
Antirain - resistant water-repellent nano-coating for car windows
VIDEO
Removing dents without painting a car in AutoTOTEMM
VIDEO
How we do local repairs in 3 hours. “AutoTOTEMM”: painting a scratch on a Porsche bumper
VIDEO
Feedback about the service: I am your regular customer, they served very well. While my work was being done, I had a nice conversation with the administrator Olga. I understand that she is new because I have not seen her in your Service before. It's a shame that Olga did not give her personal number. I plan to come to you one of these days and make Ceramics. Since I heard a lot of positive feedback about Ceramics.
Feedback on the quality of repair: Quickly and efficiently.
Your wishes: Success in work.
Full name: Andrey
You always try to be as accurate as possible, and even more so in a car, because it's like a second home. But sometimes incidents happen that may not even depend on you. For example, someone accidentally dropped a cigarette butt or shook off the ashes on the seat and that's it - the trim is burned, and the appearance of the interior is damaged.
In modern cars, special synthetic materials are used for seat upholstery, which are easy to care for, but they quickly burn through when ash enters. The fabric on modern cars is made of a material that quickly burns out and a touch with a cigarette butt causes a burn, which is very noticeable. When you drive, you may not notice how the ashes are shaken off, because your task is to carefully monitor the road, not the cigarette.
Previously, burning through was a serious problem, because in order to return the interior of the car to its original appearance, it was necessary to reupholster the entire seat. Fortunately, now the car seat burn repair service will not take you much time and money, because they will simply put a special pile on the fabric seat on the problem area, and the burn on the leather seat will be filled with liquid leather, which will be almost impossible to distinguish from the original.
But you must understand that the further you delay with this cosmetic repair, the more money you will have to pay for the service. After all, if the burn is located in a place with which you or passengers often come into contact, then over time this can exacerbate the problem. But if everything is done on time, you can be sure that the repair will not take you a lot of time and money.
No Defect Auto Atelier will service your car and provide seat burn repair service. You just need to register and come. Your seat will be like new.
How to fix a car seat yourself?
When should a car seat be repaired?
Types of car seat defects
Required material and tools
We start repair
Preparatory stage
Tilt mechanism repair
Seat heating repair
Seat upholstery repair
How do you know when your car seats need repair interventions? In fact, everything is quite simple here. As soon as you no longer like their appearance, or staying in the cabin becomes extremely inconvenient, and the former functions no longer differ in their previous reliability, then we can certainly argue about the need for repair actions.
The most common problem that requires car seat restoration work is the wear and tear of the upholstery in the area of \u200b\u200bthe pillows and armrests, and it is noticeable even to the naked eye: individual sections of the seats change color over time, crack and become very repulsive.
In a separate group, mechanical defects that are not associated with long-term operation of the car should be combined. In particular, they include burns, tears, cuts and broken bases caused by the impact of any large load or simply careless handling by the car owner.
Depending on the type of damage, the appropriate way to eliminate the problem that has arisen is also chosen: whether it is repairing the upholstery or replacing metal parts at the base of the car seats. In any case, you will need the appropriate tools and materials.
To get started, prepare a few pieces of new upholstery, because such common scuffs, severe cuts and scratches are mainly eliminated with their help. The color and quality of the purchased material completely depend on your preferences, but the main thing is that the salon looks harmonious as a result. Synthetic, artificial or even genuine leather, as well as any other upholstery fabric, is suitable for work. Of the tools, hand sewing needles, an awl, glue and several types of thread are useful. If minor damage is present in leatherette or velor upholstery, then special compounds that can be found in any automotive store will help eliminate them.
Mounting and dismantling of the chair, as well as correcting frame defects, will require the use of a set of wrenches, screwdrivers, pliers, a hammer, and a hacksaw. It will also be useful to have a vacuum cleaner to help clean the seats before doing all the work.
Like any other type of activity, the repair of leather, velor or other types of vehicle seats involves a series of sequential actions.
If the problem is only minor damage (such as a cut or burn), then after cleaning the required area, you can proceed to the direct elimination of the problem using a pre-purchased repair kit. However, in the event that the problem lies much deeper, and the tilt mechanism or heating system needs repair, then the chair will have to be completely disassembled. It is most comfortable to perform this task on a table with a workbench. You can unscrew the fasteners on both sides of the seat using a conventional screwdriver. It is better to postpone the back with a pillow for the time being, in order to repair it later if necessary.
In the event of a malfunction of the spring block or a complete replacement of the skin, the old material will have to be removed from the seat. To do this, all the seams on the damaged seat are carefully opened with a sharp knife. To quickly complete the task, the fabric should be well stretched, so that all seams are clearly visible. Also, at the preparatory stage, they collect all the tools necessary for subsequent work.
During the active use of the car, it often becomes necessary to replace the inclined mechanisms that are responsible for changing the position of the seat back. This type of repair of car seats is quite laborious, so it is better not to take it to extremes and constantly monitor the operation of the tilting mechanism. If any malfunctions or jams are found, they can be easily eliminated with lubrication.
In the process of replacing the tilt mechanism that adjusts the angle of the car seat back, All repair actions are carried out in the following sequence:
• first you need to remove the lining (located at the base of the pillow);
• then unscrew all fixing bolts that hold the lower link of the hinges at the very base of the car seat, and, having got rid of the axle located on the opposite side of the backrest, dismantle the back itself;
• the upper link of the hinges must be cut off at the base of the backrest frame, after which the new mechanism should be fixed with bolts at the very bottom of the cushion;
• the upper link should be put in the right position so that all the holes can be aligned;
• The pillow should be connected to the back of the seat with the help of an axle: by controlling
• the position of the part, place the backrest and attach the hinges to it by means of welding.
If you have the skills of an electrician, then you can independently check the health of the wires and plugs. But heating repairs can only be performed if you own a vehicle without an on-board computer, otherwise, there is no point in turning off the heating for the sake of self-repair (as mentioned above, a competent re-configuration of the on-board computer can only be done at a service station).
For those who nevertheless decided to repair car seats with their own hands, you need to know that this procedure requires a responsible approach and considerable patience.
Get rid of scratches and scuffs
The easiest way to repair car seats is to eliminate scratches and scuffs on leather upholstery. If only the layer of paint that is applied to the surface is damaged, then for repair purposes you will need either a special spray paint or an appropriate polish with a filler.
It is quite possible that in your case the interior of the car is not leather, but, say, velor, then to eliminate defects you will need a needle, thread and patterns that can be made from fragments of old upholstery. When choosing a repair kit, you need to pay attention to one important detail: all the fibers included in the kit must be of different colors. Using a special brush and glue (or spray), fibers of the appropriate color and texture are applied to the damaged area of the seat. To fix the result, the restored area is covered with a Teflon film and ironed.
Eliminate tears and cuts
Today, the market offers a fairly large number of products for the care and repair of car seats inside the vehicle. Therefore, if you need to restore the car seat, then there should be no problems with the selection of material.
Restoring leather seats will require a little more effort and a liquid analogue of leather, along with a mesh and a suitable repair kit. All irregularities (for example, the edges of a cut) are carefully sanded with sandpaper. After that, a small plastic mesh is applied to the cut or tear and the area is filled with liquid skin.
The fabric interior is restored using a patch of the desired shape, made from a similar material (parts of the old interior can be used). To recreate the color, you need to choose the right paint and use the color to color the new elements of the chairs. Such restoration of car seats perfectly helps to hide the most noticeable damage.
The restoration of the plastic elements of the seat follows a similar scenario, only all cracks, chips and holes are filled with a granular composition that perfectly imitates a plastic surface. At the final stage, the damaged area is painted with paint of the corresponding color. When done correctly, no one will notice traces of damage.
We restore the seams
Direct restoration of car seat seams involves several sequential steps: first, three stitches must be retreated from the end of the thread, looking for a hole from the old seam there. Then all the layers of the seat are collected in one pile: after passing the clip with the needle through all the layers of the seat, it is necessary to leave it in this position and insert the thread into the eyelet. After that, the needle is pulled back, pulling the thread out through all the layers of the seat. Having found the next hole from the last seam, thread the needle through it and sew all the layers again. Thus, a loop should form, and if you thread a thread through it, you will get a knot.
The process continues until everything is sewn to the end. After tying the last knot, cut off the excess ends of the thread and inspect the seam from the front side - the tear should be completely eliminated.
Video (click to play).
