Do-it-yourself chair seat repair

In detail: do-it-yourself chair seat repair from a real master for the site my.housecope.com.

In an upholstered chair, the seat sags over time, and its upholstery fades, wipes off and even tears. But throwing away such chairs is not worth it: fixing them is quite within the power of a home master.

All furniture sooner or later falls into disrepair.

Here and at our old chairs, the upholstery was wiped off in places, and foam rubber fell down from the underside of the seats.

The chairs were made quite soundly - and I did not want to throw them away. Therefore, the chairs in the amount of six pieces migrated to the country. And so. after the end of the summer season, hands reached their repair.

The removable seat frames of all chairs were in good condition, and it was only necessary to turn the seat upholstery.

Chair upholstery - it's a simple matter. The main thing is desire and a small amount of tools and material.

The first thing I did was remove the old upholstery from all the seats (no jewels were found). But the foam rubber that fell into disrepair was formed abound. Not only did it crumble, it was also sticky - I had to scrape off the remnants of it with a knife. Longitudinal flat springs are installed on the seat frame, which are well preserved. But I decided to slightly improve the spring system.

I attached a strip of stainless steel perpendicular to the springs to each frame from below with screws: it will protect the springs from strong deflection and thus prevent the new foam rubber and upholstery from quickly spoiling. So that the foam rubber does not lie directly on the springs Do-it-yourself chair seat repair (photo) oh, I decided to put thick synthetic material from the old carpet under it. I cut it to the size of the frame and attached it with a stapler.

Video (click to play).

Prepared all six chairs in the same way. I purchased foam rubber 2 cm thick. I made a pattern for it with an allowance of 1 cm around the entire perimeter. The upholstery material was provided by the wife from old stocks. It turned out to be a motley-colored velveteen - this is quite suitable for giving.

Cutting velveteen did with a margin for bending. After cutting, I began to fasten the upholstery with staples. First of all, I fixed the material with a slight interference in the middle of the opposite sides of the frame. Then he wrapped the corners - and also secured them with brackets. Then, evenly stretching the material, I attached the remaining parts.

In conclusion, I decided to close all the bends, springs and matting with white dense material. I also cut it (material) with a small allowance - and fixed it. Now the seat looked good from any angle. It remains to install the seats in place - and you can use the updated chairs.

1.Kachal from the fact that he took off the old upholstery.

2. For reliability, I attached a strip of stainless steel perpendicular to the springs.

3-4. New foam rubber and upholstery fabric cut out for the seats with a small allowance.

5. Fastened the fabric with snobs, starting from the middle of the sides of the wound.

6. White dense material covered the seat from below.

7. Updated ones will still serve not really in the country

An armchair is an integral attribute of the interior, which is found in almost every home. A person uses this furniture almost every day, which leads to a deterioration in its condition. Such an operation as the repair of chairs will help restore the technical parameters of the design.

Furniture repair is a complex operation, which depends on the type of product and the breakdown itself. Today, such operations are rarely carried out independently. It is advisable to entrust the solution of such tasks to experienced specialists who will perform them much faster and better.

Restoration of furniture is the restoration of not only its functionality, but also its appearance. A feature of upholstered furniture is that it uses fabric upholstery. To repair the internal structure, the fabric will need to be dismantled or replaced. This operation also requires certain skills and efforts.

Breaking the chair is not always a problem, as you can try to restore its condition yourself. There are several types of operations that are easily performed at home:

Padding. This process involves replacing the old fabric with a new one. This also includes changing the filler (foam rubber, etc.) and restoring the internal structure of the chair. If necessary, the wooden surface itself can be restored.
Upholstery. This approach involves upholstering fabric on the surface of the chair in order to update its appearance. Often such operations are performed with old rigid structures, the surface of which is not so easy to restore with paint.
Repair. This is a general concept, which includes the previously considered operations. But often this word is understood as all the repair work associated with restoring the condition of the chair frame. This includes strengthening the structure with metal corners, replacing legs or seats, as well as restoring the surface of the material with paint and sanding.

To carry out all the previously described operations, you should not only have experience, but also stock up on a lot of special tools.

Modern chairs are made from various materials. The design of such modifications consists of many elements that can be replaced if necessary. Often, such chairs include office models that are equipped with a gas-lift mechanism. For the restoration of such products, several types of components may be needed:

Rollers. This mechanism is made of various types of plastic. When choosing this product, it is important to consider its purpose, connector type and method of fixation.
Gaslift. Almost all office chairs are equipped with this element, which allows you to hold the chair at a certain height. There are several types of these structures on the market today. It is important to pay attention to the type of mechanism that was previously used in the damaged chair.
Cross. Plays the role of a support element. Performed in the form of a 5-ray star, to which the rollers are attached. When buying, it is important to pay attention to the quality of the material and the way the parts are connected.

There are many other accessories that will be needed when repairing such furniture. This includes everything from small knobs and bolts to specialized fabrics.

One way to restore an old leather chair is to reupholster it. This process is quite lengthy and laborious. First of all, new fabric is bought. Padding can be done with leather and other popular materials. Some experts also recommend purchasing stuffing materials (foam rubber, batting). To simplify the hauling operation, you must also have a stapler, nails, hammer, etc.

The algorithm for solving this problem can be described in several successive steps:

The chair upholstery process is slightly different from the upholstery, although in many ways it is very similar. This operation involves covering the chair with a cloth. For such purposes, only furniture is used that was not originally equipped with fabric upholstery.

Upholstery technology involves several sequential operations:

All other elements are sheathed in the same way. If necessary, the material can be cut.

Old chairs are often very strong and durable. But after a long period of operation, they lose their attractive appearance. Do not rush to throw away such furniture, as it can be easily restored.

Old wooden furniture in the house after many years of use takes on a shabby look. Worn or scratched surface, loose connections. Natural wood products retain the quality of individual parts after many years of use. Inside a dry room, the tree remains for a long time. Connections are mainly destroyed.

Do-it-yourself chair repair scheme.

Repairing an old chair with your own hands allows you to return to life and home use a comfortable and favorite piece of furniture.

In addition, it is economically justified - to get a new beautiful piece of furniture at minimal cost.

As a rule, the restoration of chairs consists of two steps. The first is to restore connections, the second is to restore the appearance of the surface. Sometimes repairing an old chair requires replacing some parts. Repair of upholstered chairs is carried out with the replacement (upholstery) of the soft fabric part.

Let us consider in more detail the sequence of actions in repairing an old chair with your own hands.

Scheme of a folding chair with your own hands.

restoration of a chair begins with its dismantling. At the same time, all the details and joints of the old chair are marked with small notches so that after repair it can be easily assembled. Nuts and screws are unscrewed, screws and bolts are removed. Rusted connections are treated with technical oil or anti-rust. A wet cloth dipped in hot water is placed on the glued joints. After the epoxy glue is soaked, the glue bow is disassembled, and the remaining glue is scraped off. Pressed connections are carefully disassembled with a flathead screwdriver or chisel, without applying too much force. You can lightly tap with a hammer on too tight old joints. Control of the strength of the impact applied to the furniture is necessary to prevent breakage of parts, after all, they are wooden, not metal. Those connections that have retained their unbreakable strength and reliability can not be dismantled. After disassembling the surface, the parts are cleaned of debris and remnants of the old coating;
surface restoration - do-it-yourself cleaning of the wooden surface of the chair from dust and dirt, from drops of paint (if the chair was in the room being repaired), old varnish and a layer of old paint is first done with a rag, then scraped off with a sharp object (for example, a knife) and sanded with sandpaper or grinder. When grinding, sanding paper is used first with a larger grit, then with a smaller one, to obtain an even and smooth surface. Old paint can be removed with a special solvent;
repair of individual parts. Existing cracks are sealed, primed and left to dry for two days. After drying, another grinding of the surface is carried out, finally preparing it for painting.

Do-it-yourself restoration of the joints and joints of the chair is carried out in different ways, their choice depends on the nature of the joints:

Do-it-yourself chair restoration scheme.

for chairs in which the legs are inserted into the seat with an interference fit (pressed in), the characteristic destruction is the loosening of the joints. Driving a small peg into the upper end of the leg will help increase the density and strength of the connection. To do this, a gap is pre-sawed in the end face. As a result, the size of the end expands slightly, and the joints in the old chair acquire sufficient density. The ends (trunnions) worn out on the outer surface are restored by winding a bandage dipped in PVA glue. Before final assembly, the recesses in the seat are smeared with glue;
chairs that had crossbars in the design for connecting between the legs are loosened not only along the joints of the legs to the seat, but also in the joints of the crossbars to the legs. They most often can not be disassembled, but screwed in screws and additionally glued.For gluing, a narrow hole is drilled through which drops of glue are injected into the joint using a syringe. You can increase the density of closure by driving in small narrow wedges;
when restoring chairs with loose screw connections, a match is inserted into a too wide connection diameter (as a wedge) and then a screw is screwed in;
any connections can be securely reinforced with metal corners.

Diagram of the design and dimensions of the chair.

after assembly, the structure is primed and covered with a coating - varnish or paint. Options for the original coating - decoupage or painting, inscription on chairs or one drawing in parts for two seats;
the new upholstery of the old chair will be done with the fabric you like when the chair is painted and dried. Old fabric and padding are removed completely and without regret. In accordance with the dimensions of the seat, foam rubber and outer fabric are cut out. Then they are superimposed on the seat, aligned and stretched. Folds are made in the corners, the fabric is tucked up and fastened with paper clips and a special stapler or carnations with a wide hat;
adding original details, decorations. For example, you can make additional details in the form of deer antlers, donkey ears, or a baby chair with a soft back in the form of an animal.

An interesting thought: the fastest restoration event will be sewing a cover. Such a measure will allow in a limited time to decorate the interior with a restored piece of furniture.

There are many ideas for the restoration and further use of old chairs. From the details of a chair that has served its purpose, you can make a garden swing with a back, a flower garden, a hanger, a coat hanger or a dog feeder, all these items can be made in an original design from an old chair with your own hands. But the most correct decision would be to give a second life to a used piece of furniture and create a new chic seating item based on it.An armchair is a common part of the living room interior. Its frequent use leads to a deterioration in appearance. Do-it-yourself chair repair will help to cope with this problem, during which the upholstery and seat filler are updated. Image - Do-it-yourself chair seat repair

Do not immediately throw away old furniture. From it you can easily make a bright interior detail without going to a specialized workshop. Before you start remodeling an old chair with your own hands, you need to decide on the type of breakdown, type of product and prepare the necessary tools and materials. There are several types of operations that can be carried out independently:

Depending on the experience and complexity of the design, these procedures will require from 1 to 4 hours.

Knowing how to properly repair a chair, most of the procedures for its restoration can be done in a home workshop. To do this, you need to prepare all the components, materials and tools.

If the set of tools for furniture restoration is always approximately the same, then the choice of components for repairing chairs depends on the type of damage and the type of product. To repair an office chair, you will need casters, a cross and a gas lift. All of them are selected according to the type of construction. The minimum set of tools that you will need to update your home chair:

hand tools: hammer, screwdriver, pliers;

scissors, manual stapler;

sling, high-strength tape, textiles and accessories;

seat filler: foam rubber, synthetic winterizer, batting;

PVA glue;

gauze;

upholstery fabric.

This is a basic set of tools that will be supplemented depending on the type of repair. For example, in order to remake an old chair with wooden armrests, wooden structures are needed; You can remake furniture by sanding, further painting or varnishing. This will require additional equipment and materials.Do-it-yourself repair of any chair begins with its disassembly and study of the design. The main internal parts of the structure:

wooden frame;

filler on the back and seat;

textile or rubber slings;

armrests;

plywood on the back wall;

Consideration of these details will help determine which components need to be replaced, repaired when reworking old Soviet chairs.Parts of the chipboard seat that begin to crumble must be replaced. Breakages and cracks in the tree are smeared with glue and fixed with staples. All parts in the spiked joints are carefully knocked out with a rubber mallet so that there is no damage to the polish and edges. The grooves are cleaned of glue with a scalpel or knife. The details of the spike joints are coated with PVA glue, the bandage is wound around the spike and all the details are hammered into place. It takes about a day to dry completely.What to do if your hand does not rise to throw away an old sagging chair that belonged to your grandmother? Do-it-yourself furniture restoration is not as difficult as it seems at first glance.The technology of repairing upholstered furniture, apparently, will never become outdated, because it allows you to breathe new life into old and lost their appearance chairs, sofas and armchairs. Of course, buying new furniture is much easier, but what if you don’t raise your hand to throw away a beautiful old chair that has belonged to several generations of the family?
Compared to renovating a sofa, which requires the knowledge and skills of a professional, renovating a chair is not that difficult. True, you will have to show perseverance and accuracy.The complex of operations to repair the seat of a chair is called upholstery. The essence of the main stages of work (braiding, installation of springs, stuffing with filler, etc.) does not depend on the model and type of chair.Then install the springs, i.e. install them on a stretched band. When upholstering upholstered furniture, springs of various sizes are used. If you are going to use wooden wedges, then the springs should be 2 cm above their ends. When repairing a chair without wedges, select the springs so that they correspond in height to the already finished finished chair (height is measured in the middle of the seat).Distribute the springs evenly over the area of the seat so that they are symmetrical about the central axis of the chair. The knots on their top flares (or circles) should converge toward the center of the seat. Sew the springs to the braid, then tie them with two strings, while making loops from the first, and knots from the second (also called “return string”).

Tie the springs with twine so that they are lower in the back of the seat than in the front. Then additionally fasten them with an intermediate cord and cover with a dense cloth, sewing it to each spring and nailing it to the wedges and the seat rails.Using a curved needle and cord, sew the first seam on a dense fabric 3 cm from the edge of the seat, then sew two or three smaller seams. At the cords, leave free ends about 3 cm long for attaching hair filler (usually of plant origin).How to make a professional restoration of chairs with your own hands using improvised means? It's quite easy!The appearance of furniture over time can become unpresentable. In addition, it sometimes breaks down and needs repair. Restoring a chair that can serve for many more years is not at all difficult. Sometimes you just need to update the surface - change the upholstery or make the seat more durable. There are many materials for restoration in the house - a piece of dense fabric, foam rubber, etc. The updated chair, covered with a beautiful varnish, looks no less neat than when you bought it.The appearance of furniture over time can become unpresentable.A home-restored chair can be designed better than it looked before. Restoration requires a minimum of materials and tools.Replacing a leaky or frayed upholstery is a matter of one hour.If the chair is antique, then you need to restore it very carefully.You can independently clean the wooden surface of old furniture and cover it with a transparent or tinted composition, add new elements to the decor. For example, a chair is made with carved legs or a back, and the seat is reinforced so that it can be used for its intended purpose for a long time.There are many materials for restoration in the house - a piece of dense fabric, foam rubber, etc.Restoration costs at home are minimal. Before buying a new chair, think about whether it is possible to restore the old one and save a lot at the same time. Restoration of antique furniture is especially expensive because it requires great care and exclusive materials. Updating furniture on your own will be much cheaper.The updated chair, covered with a beautiful varnish, looks no less neat than when you bought it.If the "native" bolts connecting the supporting structure are loosened, then they are strengthened with an additional washer. For greater reliability, you can add a little universal glue to the grooves. Image - Do-it-yourself chair seat repair

Replace the seagrass and horsehair used in the old days as fillers with foam rubber.

A leaky seat is updated by replacing the base with slats and / or completely restoring the upholstery. The worn surface is freed from the old material. The chair is being prepared for further restoration:

cut a piece of plywood to fit the seat;
stick foam rubber on the base (width - 3-4 cm);
fix plywood around the perimeter;
stretch the upholstery fabric on the finished base;
fix the material with a stapler and staples.

A home-restored chair can be designed better than it looked before.

You can completely replace the back with a figured one, if the design allows.

You can not bring the fabric to the outer sides of the seat. Then the upholstery is tucked around the perimeter inward. The seat frame will be visible.

The fabric is selected resistant to abrasion and mechanical stress, sufficiently dense.

The restored chair can be additionally decorated - to make the wooden surface lighter or darker, to decorate the back or legs in a different way.

Replacing a leaky or frayed upholstery is a matter of one hour.

When updating, you can use a variety of materials. With a good carpentry skill, the restored chair acquires an individual style. This takes into account the material - wood species, density, texture.

You can independently clean the wooden surface of old furniture and cover it with a transparent or tinted composition, add new elements to the decor.

The chairs included in the set must be decorated in the same style.

If the chair is antique, then you need to restore it very carefully. Be sure to give time to dry the applied composition.

For an antique chair, choose a decorative material with embroidery.

For your information. Antique chairs often come with springs in the seat area, so you will need to find the same or similar ones, and remove the old, rusted and lost elasticity. Replace the seagrass and horsehair used in the old days as fillers with foam rubber.

Restoration costs at home are minimal.

Round the edges using a jigsaw, clean the edges with sandpaper.

To restore the chairs you will need the following:

quick-drying varnish (transparent or tinted);
dye;
upholstery fabric;
foam rubber;
plywood;
sandpaper;
metal washers and bolts (screws);
springs (for a specific type of chairs).

Sandpaper will be required in order to clean the surface of the furniture from bumps, chips and cracks in the varnish.

The fabric is selected resistant to abrasion and mechanical stress, sufficiently dense. Tapestry, flock, matting, etc. will do. For an antique chair, choose a decorative material with embroidery.

Updating furniture on your own will be much cheaper.

Select in advance the density, texture of the wooden base, cut it to size and use the template to draw the desired pattern.

Sandpaper will be required in order to clean the surface of the furniture from bumps, chips and cracks in the varnish. It is necessary to completely sand the chair (wooden structure) for a smooth application of the laminating composition.

For serious repairs, the chair can be disassembled, the broken parts replaced with new ones and fastened with bolts or screws.

To update the chair, you need tools:

scissors;
roulette;
hacksaw for wood (saw off excess plywood under the seat);
screwdriver;
screwdriver.

For greater reliability, you can add a little universal glue to the grooves.

For serious repairs, the chair can be disassembled, the broken parts replaced with new ones and fastened with bolts or screws. Seat frames also often require restoration.

Seat frames also often require restoration.

A Viennese chair or any other chair looks best in this design.

Important! It is necessary to use wood species close in density and texture so that the chair is functional and looks presentable.

A leaky seat is updated by replacing the base with slats and / or completely restoring the upholstery.

There are several options for designing the appearance of furniture. The chair can be updated in the following ways:

It is necessary to use wood species close in density and texture so that the chair is functional and looks presentable.

As a decor, you can use both the upholstery itself, choosing a fabric of interesting colors like a tapestry, and other parts of the furniture, making them carved, figured.

You can not bring the fabric to the outer sides of the seat.

A plain seat is decorated with smooth embroidery or appliqué. This must be done before starting the plating.

A plain seat is decorated with smooth embroidery or appliqué.

The wooden surface of the supporting structure and the back are laminated, that is, they are coated with a resistant varnish in several layers. The tone of the coating is selected closer to the natural shade of the tree (light, dark or moderate). A Viennese chair or any other chair looks best in this design.

The restored chair can be additionally decorated - to make the wooden surface lighter or darker, to decorate the back or legs in a different way.

You can completely replace the back with a figured one, if the design allows. Select in advance the density, texture of the wooden base, cut it to size and use the template to draw the desired pattern. Round the edges using a jigsaw, clean the edges with sandpaper.

The wooden surface of the supporting structure and the back are laminated, that is, they are coated with a resistant varnish in several layers.

The chairs included in the kit must be designed in the same style so that they do not stand out from the overall picture - "various" furniture can look good in different rooms, but at a common table, for example, when celebrating a family celebration, it looks careless.

When updating, you can use a variety of materials.

VIDEO: Chair restoration: How to make a chair with your own hands. Master class from Katerina Sanina: design, interior

Judging by the views of my four-part MK (its first part is https://my.housecope.com/wp-content/uploads/ext/1739/topic/486697-restavratsiya-venskogo-stula-chast-pervaya-podgotovitelnye-raboty?vr =1&inside=1 ), dedicated to the Viennese chair, I conclude that this topic is interesting. Therefore, I am printing another MK dedicated to this topic. Anyone who is interested in my publications regarding the Viennese chair, I recommend that you watch another two-part MK on replacing a broken bar stool leg (the beginning of this MK is https://my.housecope.com/wp-content/uploads/ext/1739/topic /448841-zamena-krugloj-pronozhki-u-barnogo-stula-chast-1-izgotovlenie-detalej?vr=1&inside=1 ) That's what happened to this Viennese chair - the seat came off.During restoration, as I once wrote, the most important rule is not to “overdo it”, i.e. it is necessary, of course, to try to the maximum to leave the original elements on the chair. Here the seat did not break, just from the hard use of the chair, it peeled off from the base of the seat. In our case, to repair the chair, you just need to glue the well-preserved seat to the old place. And so that such a breakdown does not occur as long as possible, I decided to strengthen the gluing unit. How to do this - I will tell you in this Master class.We apply the prepared glue with a thick layer on the base of the seat of the chair, Image - Do-it-yourself chair seat repair

especially on the wide part of the base, where we attach the front legs.

With the help of specially sawn oval overlays, we fix the glued knots with clamps.

At the same time, it is clear that the lining under the clamps should be placed from below.

To fix the glued back part, you have to do a partial disassembly of the chair. We remove the element of the back and the rear leg.

Now we clamp this knot with a clamp.

After a day, we put the disassembled elements in place and proceed to the epoxy putty. Carefully apply adhesive putty, naturally with filler, with a knife on the perimeter of the entire seat. If there are gaps, they should also be filled.

remove excess glue carefully.

You can begin to strengthen the gluing nodes. I took four wooden slats 1 x 1 cm, trimmed their edges with a knife (so that they fit the shape of the roundness of the seat), generously smeared these elements with glue at the junction with the back of the seat and the base of the seat. And in order to fix these knots while the glue dries, I hammered small nails along the edges of the rails directly to the base of the seat.

It turned out here is such a picture.

A day later, after the glue has set, we finish the work. We cover the lower part of the seat and the strengthening elements with a stain.

And varnish the outer part of the seat. To make the chair look more attractive, I varnished the armrests and the side of the seat base. In my case, one coat of lacquer was sufficient. It turned out the following:

On this, after the varnish has dried, the repair is completed. In principle, if it were not for the time spent on the technological drying of the glue, then the repair would not take so much time. I remind you that the varnish must dry and gain its strength. This usually takes at least three days.

This concludes my next story, thank you for your attention,

If you have an old chair at home, do not rush to throw it away, try to update it! To restore the chair, you do not even need to contact a special workshop, it is easy to repair it yourself.

Do-it-yourself chair repair is a completely simple task and accessible to any beginner. In this article, we will introduce you to a simple restoration of a chair with wooden window sills.

First, let's take care of the necessary tools.

To restore an old chair, you may need:

stain of a suitable shade;
construction stapler;
varnish for furniture (lacquer in a bottle is suitable);
screwdriver;
vibration grinder;
upholstery material (you can also use material for curtains);
drill;
foam rubber (to make the seats softer and thicker);
wooden shield;
wood glue.

Remove the coarse calico (spunbond, chernukha) from the bottom of the seat. Under it, you need to find and unscrew the four nuts.

Then we open the back of plywood or fiberboard upholstered with fabric, we find 2 nuts. After completing these simple steps, remove the armrests.

The back and seat are fastened with two more bolts. We also unscrew them and disassemble them into separate elements. As a result, the chair is disassembled into the following elements: seat, backrest, 2 armrests and backrest.

The upholstery material can be removed in two ways:

slowly, carefully pulling out the staples with the staple remover;
in order to save time, you can simply rip it off with pliers and a powerful screwdriver.

When removing the upholstery, keep in mind that there is a large amount of debris under it. After removing the upholstery, be sure to remove any old staples from the frame or punch them with a hammer.

First you need to inspect the wooden parts of the chair for breakages and cracks. They must be glued with wood glue and fixed with a 16 mm bracket.

If, when disassembling the chair, you notice that one of the parts of the legs has dried out and begins to crumble, you will have to replace it. For this purpose, you can use a wooden furniture board.

Next, you need to sand the details. This process is the hardest and longest. Using a special nozzle for a drill, we remove the varnish from the parts. Then, using a grinder, we clean them until a shade of wood appears.

From the construction board we cut out the elements of the required shape. We cover the details with a stain and wait about 5-6 hours.

After this time, we cover the parts with furniture varnish. If you want to keep the effect of wood, do not try to apply too thick and shiny varnish. The varnish dries approximately from 22 to 24 hours, depending on the thickness of the coating.

Check how tight the belts are. If not too tight, then remove the bracket on one side and using pliers, pull harder. Broken belts will need to be replaced. For this, special elastic belts for furniture, rubber strips or any dense fabric are suitable.

It is also desirable to make a drum of dense fabric over the belts, it covers the belts and is nailed with staples. Thanks to the drum, the belts will last much longer, and the old foam rubber will not spill out.

First of all, we look at the condition of the foam rubber or foam rubber. If the condition leaves much to be desired, then it must be changed or attempted to be restored.

To replace, you need to measure the thickness of the old filler and add another 1-2 cm to it (after a while, the foam rubber sank) - we need such foam rubber.

For the repair of chairs, special foam rubber is used for furniture with a density of 22-25 and a thickness of 1-3 cm (depending on the condition of the old filler).

To increase the density between the new foam rubber and the old foam rubber, you need to glue spunbond or coarse calico. The new foam rubber is glued and fixed around the perimeter with brackets.

Having done all the preparatory work, we cover the individual elements with a cloth.

We pre-measure the old fabric and make a margin of 3-5 cm on each side. Having made the necessary measurements, we cut a new fabric.

Remember to make a good stretch. The corners must be fixed last. We break through the staples, observing a distance of 2-3 cm. It makes no sense to do this more often, and if less often, differences will be visible on the new material.

Once the upholstery is done, use a long screwdriver to poke holes for the bolts and punch the staples around them so the material doesn't tear at that point.

Assemble the chair in reverse order. Nuts and bolts can be replaced. Be sure to tighten through the washers, over time the nuts can be pressed into the tree and the frame will wobble. On the lower part of the seat we nail a new calico and, if any, a piece of new fabric.

That's all, the repair is completed. As you can see, restoring a chair is not so difficult, if there is a desire. Enjoy the updated vintage style armchair!