Do-it-yourself grohe eurosmart faucet repair

Choose reliable masters without intermediaries and save up to 40%!

1. Fill out an application
2. Get quotes from masters
3. Select artists by price and reviews

Submit a job and find out the prices

Regular use of sanitary equipment both in the kitchen and in the bathroom requires manufacturers to improve the quality and expand the functionality of their products.
From a number of proposals on the sanitary equipment market, Grohe bathroom faucets stand out favorably, repairs for which are very rarely required, due to the excellent quality and reliability of the units. However, long enough improper operation and high water hardness can also damage these devices.
You can repair Grohe brand faucets yourself at home. However, this is a rather laborious procedure that requires patience and perseverance.
You can repair faucets with the usual set of tools that every home has.

Grohe brand faucets can be subject to various kinds of malfunctions:

• Unit leak
• Water flows slowly from the faucet
• Problems associated with the operation of the mixer in the "bath-shower" mode
• Poorly installed switch

Repair of a single-lever mixer is slightly different from that of a two-valve device. But the main causes of malfunctions of Grohe brand faucets in these cases may be:

• Blockage of the switch with small particles. This is possible if the running water is contaminated.
• High water hardness
• Natural wear of structural parts

Experts strongly recommend using tap filters with openings no larger than 100 microns to prevent abrasive particles from entering the faucets.

Depending on the type of problem, the following manipulations are performed:

• Troubleshooting Cartridge Operation

As a rule, small abrasive particles contained in running water get stuck inside the ceramic disc of a single-lever device. This may cause the mixer to leak.
To restore normal operation of the unit, it is necessary to completely replace the entire shutter.
How to do it:

• Remove the plug from the front of the unit (there is a decorative marking in blue and red colors)
• Remove the screw that holds the lever
• Remove the unit from the housing
• Remove the defective filter (cartridge) and replace it with a new one

Install the lever in its place, following the reverse sequence of actions.
This principle is suitable for almost any model of mixers, not only the Grohe brand.

The faucets in the kitchen are also repaired in the same way.

• Low water pressure from the tap

Grohe faucets are equipped with the SpeadCleen system. It involves inserting silicone pads into the filter. If the cartridge is clogged with limescale, just run your finger over the insert and the water pressure will be restored.

Older model faucets include metal meshes. In this case, do the following:

• Remove metal mesh
• Rinse thoroughly under running water
• Put the part back

• Restoring the function of the bath-shower mode switch

It happens that water begins to flow immediately from the tap and shower head. In such a situation, experts talk about the wear of the spool gasket. Mixers can be repaired in the following sequence:

• Screw all water supply levers
• Dismantle the hose from the shower head
• Remove adapter and drain
• Unscrew the main screw securing the control lever
• Remove eccentric
• Remove the spool gasket from the body, remove the silicone rings. To do this, you may need an awl or a flathead screwdriver.
• Install new rings and lightly moisten them.
• Put on the spool gasket and restore the structure in the opposite order

Usually new Grohe faucets come with gaskets.
You can repair mixers by making rubber rings yourself. To do this, you will need a piece of material at least three to four cm thick. Of course, they are short-lived, but they can help out in an emergency.
Faucets can also be helped out with linen thread or a thin copper gasket wound around old rings. This will slightly extend the life of the rings. However, after a while, the mixers will still have to be disassembled.

The forum was created for beginners and experienced plumbers, welders, mechanics, electricians and construction workers. Share your experience and get competent answers from experts.

Such covers are unscrewed by hand, but before that it is necessary to tap it with something suitable to stir up the dirt that has sealed the thread. It is correct to do this with a wooden block, but I use the edge of the adjustable wrench handle wrapped in a rag (so as not to chip the chrome). The blow must be “dry”, it is not necessary to punch in depth.
If your hand slips, you can unscrew it with a rubber glove.

Comfortable living conditions depend on such a household device as running water. But, and the mixer is the most important part of such a design. If you do not know how to disassemble a single-lever mixer, then this article is for you. This functional mechanism is designed to mix the streams of cold and hot water to achieve the optimum temperature. In the event of a malfunction, such a device requires urgent repair. The cause of the malfunction may be water leakage, wear of the mechanism or a decrease in the volume of the jet. It is in such situations that knowledge about disassembling and assembling the device is required.

The single-lever faucet is a functional and ergonomic mechanism with a modern design.

Single-lever products are of certain types:

• the faucet device for a bathroom faucet of a ball variety includes such a part as a ball. It provides passage recesses for different types of water (hot, mixed, cold). The container in the device is called mixing. The ball is very tightly connected to the sealing parts. The device is started from the adjustment rod;

• in a cartridge faucet, instead of a ball, there is a cartridge of two ceramic plates. At the bottom of the hole for the passage of water, and at the top there is kneading.

Internal device with cartridge system

Single-lever models are easy to use, which is why they are so popular. With their help, there is a quick adjustment of water. To decrease or increase the water pressure, the joystick moves up and down.

The disadvantages of a water tap device of this type include the rapid wear of rubber seals. To prevent malfunctions, these items should be replaced every two years.

What does a ceramic cartridge look like?

The single-lever mechanism may fail if abrasive particles enter it. Therefore, special filters are needed that prevent clogging.

Structurally, kitchen and bathroom faucets are slightly different. In kitchen designs, the height of the drain is set higher. Also in such models there is an additional switch that is used for a washing machine or dishwasher.

Tall design for the kitchen

Related article:

Kitchen faucets with tap for drinking water. The problem of poor-quality drinking water is familiar to many. In this case, you can not do without the use of filters. But there are devices that make life easier. Let's talk about them.

For a bathroom, a faucet with a short spout is more suitable, as this reduces the risk of leaks. Bathroom faucets come with a shower set.

Mixer internals

In the table you can see the prices for individual models.

Faucet leakage problems are relevant for bathrooms that we use several times a day.Small droplets dripping slowly and continuously from the faucet are the first signal that an urgent repair is needed.

It is not difficult to eliminate the breakdown, having an idea about the structure of the mechanism of the device. As they say, repairing a mixer with your own hands is a worldly affair.

Typical faucet problems are leaks caused by:

• a malfunction of the soul;
• conical plug defects;
• crane box wear.

But most often the rubber gasket wears out, the condition of the crane depends on the integrity and strength of which.

Most often, a leak from a valve is due to wear of the rubber gasket in it. This is the most common situation. Both mixer taps can leak.

You will need the tools shown in the photo:

The thickness of the new gasket is from 4 mm. You can make it from a piece of sheet rubber. The process of cutting it is the simplest, but if there are doubts about the quality of hand-made production, then in the future it is advisable to change the home-made gasket to a factory product.

As a template for cutting the gasket, the one that is to be replaced is suitable. If it is too deformed, then it should be taken into account that the manufactured part of the seal must be 1 mm larger in diameter than the previous one.

The edge resulting from the increase in Ø should be modified: cut along the circumference from the side adjacent to the seat at an angle of 45º so that this sealant tightly “enters” the hole to be closed and the valve with the new gasket does not buzz.

After replacing the gasket, everything must be returned to its place. We insert the crane box back. Usually, when removing a crane box, it is always advised to treat the internal cavity from plaque. This plaque is usually the result of water hardness. In the reverse assembly of the mixer, a plumbing adjustable wrench is used.

In most cases, mixers have problems with valves, especially with half-turn valves. The valve can be replaced or repaired. There are no particular difficulties in how to repair a broken faucet in the bathroom yourself.

In a conventional valve, which is unscrewed in a circular motion, it is most often necessary to change the gasket or gland packing. Brief instructions for replacing the gasket are posted above, and in case of problems with the gland packing, they usually try to tighten the gland.

A small nut located at the base of the crane box will be involved here. The cross section of this nut is square. In a clockwise direction, tighten the nut until it stops.

If these manipulations turn out to be useless, then it will be necessary to unscrew the gland ring. After unscrewing, a special gland packing is wound around the valve stem. Then the ring will need to be screwed back well. All of the above actions help stop the leak.

Repair of the valve seat - the cavity into which the faucet box is screwed - is necessary if, after replacing the gasket or the faucet box, water has not stopped flowing from the tap. With prolonged use of the mixer, it is often deformed, this causes leakage.

The appeared notches and scratches can be removed by milling. It is necessary to scroll the deformed area with a cutter a little. After such a scroll, the mixer is assembled, and if the seat is properly polished, there will be no leakage.

To solve this problem, you need to do the following:

• buy a switch;
• disassemble the crane;
• replace the broken part.

If deformations are found in the conical plug used to mix water from hot and cold water pipes, it must be replaced. When eliminating any breakdown, the flow of water is always blocked. The following photo shows how the switch is removed:

When eliminating the above described malfunctions, it is not necessary to remove the mixer from the mount. But there are more global problems with the valve mixer, which are also completely solvable.

Read more about some malfunctions of plug-in mixers and how to fix them.

It is possible to repair the shower-spout switching mechanism without replacement. Consider the original way of fixing the switch flywheel on the stem:

Now it remains for us to drill a hole on the switch stem and assemble the mixer:

Eliminate the leak, following a certain algorithm, and then change the mixer.

• Initially, in this situation, the water is turned off. Special taps for shutting off are located on the water supply pipes.
• After shutting off for verification, the valves are rotated in the direction of opening to the maximum.
• Then the connecting nuts are very carefully unscrewed. In modern mixer designs, they break easily. Regular brass nuts are easier to unscrew. They won't crack or break. A broken nut needs to look for an analogue in shape.
• Next, remove the mixer.

When removing the mixer, the branch pipe is turned out, at the border of which a leak is detected with the coupling. The edges of the pipe when turning out are held with a key or by a shoulder. A nut is screwed onto the removed pipe. You need to screw it in correctly, until the end. The new nut is taken from the old mixer. The reliability of the installation of the nut is determined in comparison with its original position.

When it comes to replacing the mixer, be sure to determine the size of the nozzles. The mixer is always sold complete with them. If differences are found between the old and new pipes, both are changed, and not just the one that flows. If they are identical, then only one can be changed.

To understand how the leak is removed in this case, consider the diagram:

During the installation of the pipe, there may be nuances. When screwing in, this part is held by the collar. In this case, the thread for two turns should remain free. All the rest are wound with sealing threads. Usually this seal is advised to impregnate with drying oil or oil paint. After such wetting, you must immediately screw the pipe into its proper place - this serves as a guarantee against re-formation of a leak.

Having shut off the water, they first try to simply tighten the nut, and then, after supplying water, check for leaks. If the leakage persists, the nut is unscrewed, and the mixer moves along the nozzle closer to the wall. Then you need to remove the hose attached to the bracket.

This is necessary to control the position of the mixer. When moving the mixer, look at the end of the pipe, because it is relative to it that the location of the device is changed.

This is done until it becomes possible to remove the old gasket, which is adjacent to the nut and ensures tightness. An attempt can be made to remove the gasket without touching the faucet. Often this fails. The reason for this is the gasket sticking to the pipe (to its end).

It is also impossible to pull out the pressed gasket. Then the shower is detached from the wall. This will help rotate the mixer. To facilitate rotation, all nuts on the mixer are loosened.

The gasket for replacement is simply cut out of rubberized sheets. In thickness, it should be from three to five millimeters. On the nut, it is prudent to leave free space for two threads of thread. After replacing the gasket, everything falls into place easily.

Sometimes there is a leak between the body and the sidewall. The mixer is separated from the piping, then from the shower. Take off the nose. The sidewall turns out. Then smeared with putty. You can use paint instead of putty. Do not use the mixer until the lubricant is completely dry.

Usually the problem is associated with blockages in the piping to the faucet. Pipes and sidewalls may be clogged. To correct the situation, you will need to clear the blockage. To do this, the valve head is turned out. Then a steel wire is pushed into the resulting hole. We take out all the garbage, sand. After that, you can clean the cavity with a solution of vinegar from plaque.

A similar nuisance is a sharp decrease in the pressure of water from the spout. Usually the cause of the problem lies in the blockage of the aerator. It is solved by unscrewing it and cleaning the nets. They are blown and then washed.You can use a needle to remove sand from the mesh.

What to do if the water flows, but the spout falls? This is due to the fact that the locking ring has broken. Until a new part is purchased, there is a temporary solution.

After closing the valves, you need to make an expansion ring. It is usually made from copper wire. The diameter of the material for the ring must match the diameter of the old product. After a ring is made with a soldering iron, it is advisable to treat it with liquid oil. This will prevent rust formation.

This situation is associated with the loss or breakage of the limiter. Knowing exactly where this part is located, it is easy to return it to its place. To do this, disassemble the mixer, find a malfunction and return the element to its place, applying light blows to the protruding part of the limiter with a hammer. Also, the limiter can be replaced with a small piece of brass wire - this will solve the problem of leakage at least for a while.

Sometimes troubles happen with a shower hose and a watering can, more often due to wear of individual elements or poor water quality.

Usually, water does not pass well through the mesh when there are blockages in its holes. Here, after removing the mesh, it is easy to clean it with an ordinary awl or needle.

After screwing the mesh back, the water supply and the direction of the streams are restored. And the plastic panel with holes, and the rest of the shower and faucet, can be wiped with a solution of vinegar from plaque and stains.

If the leak appeared due to wear of the inner part or winding, it does not make sense to repair the hose, it is easier to buy a new one. Its cost is low, and the service life of new modifications is much longer.

If both the drain and the shower are leaking at the same time, the point is a loose joint between the cork and the body. To correct the situation, the locking screw is first turned out. The next step is to tighten the union nut. This reduces leakage, but switching water from the drain to the shower is somewhat difficult.

To completely eliminate the leak, you need to grind the plug to the mixer body using special lapping paste compositions. They are sold in many stores.

Most people have preferred lever joystick mixers. It is very convenient to use them, since only the handle of the mixer is turned to achieve the desired water temperature. It is also very easy to create the desired water pressure by moving the lever up and down.

To understand how to fix a single-lever mixer yourself, you need to have an idea about its device.

Instead of valves with gaskets that close the channels with water, there are special cartridges here. They are usually spherical or disc. They do not need to be changed as often as the same gaskets. You cannot replace a disc cartridge with a ball cartridge. Only their cartridges are suitable for a ball lever mixer, and their own for a disk mixer.

Articulated, they are also single-lever or joystick, mixers are extremely sensitive to the quality of tap water. Therefore, malfunctions often occur not due to a breakdown or failure of the locking device, but due to the appearance of sediment and clogging of the interfaces of moving parts.

Consider how the Grohe Eurosmart 3300001 bathtub model was cleaned with the 08915 mechanism located on the spout, which switches the shower to the spout. This device did not work, the water went into both the shower head and the gander at the same time. Note that the master did not have to replace parts and seals, it was enough just to remove rust and calcium build-up.

After cleaning and washing the switching mechanism, it remains to "deal" with the pressure. As it turned out, for this it is enough to clean the spout aerator:

After the traditional water shut-off, unscrew the mixer mount. Then you will need to remove the lever as carefully as possible, and you need to do this carefully, slowly loosening it. Raise and pull out the lever only when no resistance is felt. To continue working, you need to unscrew the thread connection.

After dismantling the dome of the mixer, the plastic component will be visible. Behind it, a seal is usually visible, which needs to be cleaned or replaced. It is just a normal rubber gasket.If the ball element is damaged, it must also be replaced.

The ball is fixed with seals, the suitability of which must be monitored.

Faucets with a lever (joystick) need careful handling, they need to be used easily and smoothly.

When installing any cartridge, you need to make sure that the protrusions on it are identical to the protrusions on the mixer.

Disc cartridges rarely need to be changed as they last up to 10 years. But mixers with such a flow rate are not cheap, although they are fully justified.

A little about how to postpone the repair of the mixer for a long time. One of the simple solutions is to monitor the quality of the water supplied to the mixer, using modern mechanical filters for this. Solid particles of sand and pebbles will not spoil the parts, and they will last much longer.

It is recommended to install coarse filters at the beginning of the fork in the water supply of the dwelling. Today, a self-cleaning filter is available to the consumer. All filtered deposits from it are sent straight to the sewer. It is not always possible to install a large filter. Where it is not available, the mixer itself is connected to connecting taps, where cleaning filters are already built in.

There are filters that help reduce water hardness. This is important for ceramic faucets, as they suffer more than others due to the presence of salt deposits in the water.

And finally, advice from experienced plumbers. If pipes hum when you turn on the mixer, you need to check how well they are fixed and, if necessary, fix them with clamps. In some cases, the buzz is due to high pressure in the pipes, then a special reducer will be required to reduce the pressure. Often this noise is caused by worn valve gaskets, after replacement it disappears.

Before the upcoming gasket replacement, it will be useful to watch the following video:

In some cases, problems with faucets are due to an incorrectly installed sink or the wrong choice of model. Most of the troubles can be solved on your own, but if difficulties arise, it is better to call a plumber - professional advice or repairs have not bothered anyone yet.

Good day, dear community!
I haven't been here in a while. so long ago that I had to re-register.

Essentially the question:
I have a Grohe Eurowing faucet in my bathroom that has worked flawlessly for 5 years. A week ago, there was a problem with the watering can / shower switch - after using the shower and turning off the water, the next time you turn it on, half of the flow goes to the shower, and the other half to the spout. By pulling out the switch button, you can direct all the flow to the spout, but the loss of automatic shutdown is annoying (I have accidentally taken a small cold shower several times

).
In the instructions I found a diagram of disassembly of the mixer. But something stops me. Well, I'll pull the body of the switch into the light of day. what to do next with it?
Has anyone fixed this issue on their own?
Or do I have a direct road to the service center?

The result of the action of lime deposits. Disassemble, soak the parts in Silite. But there is one “but”: the switch parts must be lubricated with a special waterproof grease (Grohe syntheso LM220), which is difficult to get.

Disassemble, clean, lubricate, replace seals, spring.
I fill the dead mixer with antiscale for a short time, then I disassemble everything, lubricate it, etc.
Sometimes they are given away at facilities as non-residents. There is nothing very smart there. with rare exceptions

.

There was a similar byaka not so long ago, got a tiny piece of rust. Took the switch apart, cleaned it and reinstalled it. Didn't grease anything. Everything is working.

Quost wrote:
the switch parts must be lubricated with a special waterproof grease (Grohe syntheso LM220), which is difficult to obtain.

And no other will do?

Wazawai wrote:
And no other will do?

Suitable if waterproof and food grade

Thanks everyone for the responses! I will do an autopsy over the holidays. 😉

Quost wrote:
Suitable if waterproof and food grade

Well, I think the food tolerance is not relevant, this is not a kitchen faucet.
There is a small tube of silicone grease on the farm from the aquabox to the video camera. Will it fit?

BDV wrote:
There is a small tube of silicone grease on the farm from the aquabox to the video camera. Will it fit?

You have to try. I would still try CIATIM 221 (not to be confused with 201!)

Happy holidays everyone!
In general, today we got our hands on a showdown with a mixer.
Got it all apart with no problem. No lime deposits or foreign debris were found on the mechanism. According to the recommendations, I bathed in silit bengue, washed / rubbed. The stem was lubricated with silicone grease. Collected - everything works! But . only once :-( then - the same trouble, with small nuances:
no matter what position of the switch the water was turned off, when turned on, half of the flow goes to the shower, half to the spout.
-the next 5 minutes of the experiment, the reaction is as follows - with an increase in water pressure, the mixer switches to the shower itself. In my nerves, I'm leaving to smoke.
- upon returning, the picture is like this - it pours 50 to 50, nothing changes from the pressure. Empirically, a reaction to the temperature of the water was revealed: if, after running boiling water and transferring to cold water, turn off the water, then when it is turned on again, it works in the normal mode - the entire flow into the spout.
Satan though. :-/
Does anyone have a version of the reasons for what is happening?

Yes, just another crap is responsible for the “shower-spout” mode. Deverter, aka deviator, aka shower switch. Now disassemble and clean it. Using the same cleaning and lubricating agents. You will need a hex.

You must be a registered user to leave a comment.

Register in our community. It's very simple!

Or sign in with one of these services

• 
  • 
  • 
  • 

  SB3 posted a blog entry in Interesting from SB3, October 7, blog entry

  Greetings, I will continue what I started in the entry “Electrics. How things really are."

  The listing will be updated gradually. Pictures will be

  

  Sano posted a blog entry in Slab Furniture, September 27 , blog entry

  So I lived to see my workshop, which needs to be equipped and supplemented with various tools for a long time and hard.

  But the main thing is a warm room, although not your own, there is where to work until they are kicked out.

  This warehouse is quite spacious, if you remove everything you don’t need, so you have to do a lot to at least somehow start working. And the first thing I did was take out the excess and proceeded to assemble a large desktop.

• 
  • 
  • 
  • 
  • 
  • 
  • 

  Sano posted a blog entry in Slab Furniture, yesterday at 00:16 AM , blog entry

  Filling with epoxy resin slab. The first resin pouring of the slab.

  It is necessary to put the slabs on a flat base, I have a chipboard sheet, while the base sheet itself must lie strictly horizontally.

• 
  • 
  • 
  • 
  • 
  • 
  • 

  Emerald posted a topic in Tools and Equipment, September 25, 2008 , topic

• 
  • 
  • 
  • 

  Nikolai911 posted a topic in Plumbing, plumbing, heating, sewerage, October 1, topic

• 
  • 
  • 
  • 
  • 
  • 
  • 

  Sano posted a blog entry in Slab Furniture, Oct 7 , blog post

  The first attempts to do something from the imported slabs. Although what attempts can be made here, the material costs money and the right to make a mistake is as much as there is money in your pocket. Train at your own expense as they say.

  Therefore, each board is carefully examined and tried on, the proverb about measure seven times in action.

  The work itself is not tricky, creative, there are several boards and they need to be selected so that it looks beautiful and there is no overspending. All adjustment to size and trimming is done with the minimum possible removal of material, just sawed off a bit here, cut it off a little with a chisel.

• 
  • 
  • 
  • 
  • 
  • 
  • 

  KGB published an article in Tools and Equipment, October 3 , article

• 
  • 
  • 
  • 
  • 
  • 
  • 

  windsor posted a topic in Our works, August 8, 2017 , topic

  How to fix a Grohe faucet: tips from the pros

  Regular use of sanitary equipment both in the kitchen and in the bathroom requires manufacturers to improve the quality and expand the functionality of their products.
  From a number of proposals on the sanitary equipment market, Grohe bathroom faucets stand out favorably, repairs for which are very rarely required, due to the excellent quality and reliability of the units. However, long enough improper operation and high water hardness can also damage these devices.
  You can repair Grohe brand faucets yourself at home. However, this is a rather laborious procedure that requires patience and perseverance.
  You can repair faucets with the usual set of tools that every home has.

  Grohe brand faucets can be subject to various kinds of malfunctions:

  • Unit leak
  • Water flows slowly from the faucet
  • Problems associated with the operation of the mixer in the "bath-shower" mode
  • Poorly installed switch

  Repair of a single-lever mixer is slightly different from that of a two-valve device. But the main causes of malfunctions of Grohe brand faucets in these cases may be:

  • Blockage of the switch with small particles. This is possible if the running water is contaminated.
  • High water hardness
  • Natural wear of structural parts

  Experts strongly recommend using tap filters with openings no larger than 100 microns to prevent abrasive particles from entering the faucets.

  Depending on the type of problem, the following manipulations are performed:

  • Troubleshooting Cartridge Operation

  As a rule, small abrasive particles contained in running water get stuck inside the ceramic disc of a single-lever device. This may cause the mixer to leak.
  To restore normal operation of the unit, it is necessary to completely replace the entire shutter.
  How to do it:

  • Remove the plug from the front of the unit (there is a decorative marking in blue and red colors)
  • Remove the screw that holds the lever
  • Remove the unit from the housing
  • Remove the defective filter (cartridge) and replace it with a new one

  Install the lever in its place, following the reverse sequence of actions.
  This principle is suitable for almost any model of mixers, not only the Grohe brand.

  The faucets in the kitchen are also repaired in the same way.

  Grohe faucets are equipped with the SpeadCleen system. It involves inserting silicone pads into the filter. If the cartridge is clogged with limescale, just run your finger over the insert and the water pressure will be restored.

  Older model faucets include metal meshes. In this case, do the following:

  • Remove metal mesh
  • Rinse thoroughly under running water
  • Put the part back
  • Restoring the function of the bath-shower mode switch

  It happens that water begins to flow immediately from the tap and shower head. In such a situation, experts talk about the wear of the spool gasket. Mixers can be repaired in the following sequence:

  • Screw all water supply levers
  • Dismantle the hose from the shower head
  • Remove adapter and drain
  • Unscrew the main screw securing the control lever
  • Remove eccentric
  • Remove the spool gasket from the body, remove the silicone rings. To do this, you may need an awl or a flathead screwdriver.
  • Install new rings and lightly moisten them.
  • Put on the spool gasket and restore the structure in the opposite order

  Usually new Grohe faucets come with gaskets.
  You can repair mixers by making rubber rings yourself. To do this, you will need a piece of material with a thickness of at least three to four cm.Of course, they are short-lived, but they can help out in an emergency.
  Faucets can also be helped out with linen thread or a thin copper gasket wound around old rings. This will slightly extend the life of the rings. However, after a while, the mixers will still have to be disassembled.

  • Proposed mixers should be made of heavy metals. Lighter material will require a quick repair of the unit
  • Faucets with plexiglass handles are also short-lived, because. this material can break pretty quickly
  • A Grohe bathroom faucet should also be free of plastic parts. They break faster than similar metal faucets

  And get the best offers from trusted craftsmen and teams.

  1. Compare prices and choose the best conditions
  2. Responses only from interested specialists
  3. Do not waste time communicating with intermediaries

  Leave a request More than 10,000 performers
  waiting for your orders!

  Or give us a call and we will pick up a master for you on our own

  

  Rate this article: