In detail: do-it-yourself repair of a Honda chord starter from a real master for the site my.housecope.com.
Let's show how to quickly and correctly replace a faulty starter in a Honda Accord 7 (Honda Accord 7) with our own hands. Before starting work, be sure to disconnect the terminal from the battery. Unfortunately, all the explanations in the course of the video are in English, but we don't really need them, the main thing is that the process of removing the starter, the location of the mounts, the tools used, etc. is shown well and in detail. By following this instruction in steps, you can easily replace the faulty generator with a new one, or remove the old one for repair.
Video replacement, removing the starter in the Honda Accord 7:
Backup video instruction:
As you could be convinced to remove the generator in the Honda Accord 7 and then put a new one is not at all difficult if you know how to do it, not by paper instructions, where very often much is not clear or not explained.
The starter turns badly and sometimes is silent, suspicion of brushes, advise the service where they can repair the starter and I would like to order spare parts in advance
brushes (in eksist they say that these are only springs)? (9) or rear assembly assembly (7)
I think it's better to go to them with at least some spare parts The problem is not yet acute and manifests itself in the cold more often I don’t consider 80r for a brush (or a spring ??) and 1000r for a brush block a waste, since they will spin them at the same time, they will be replaced especially 50/50 that either the brushes end or bendix
I will also try to tighten + on the battery, otherwise it is inconvenient to tighten the screw on the side)
It seems that I figured out the starter - I tightened the positive wire it got better, but sneezes at the start remained (sneezes 1-3 times) those grasps and immediately releases, while the battery light blinks, the revolutions do not float can you need to clean what? what filters to change? the candles are new, the throttle, the injector has never been cleaned, the benz.filters have not changed either.
Video (click to play).
a hedgehog rarely (on weekends), the battery charge is normal before the start voltage 12.8 - 12.6, new battery
You can check the starter without being removed. It is necessary to close something there with a wire (which I did not see, since I turned the beak) in order to check the “retractor” if it turns, then the problem is exactly in it. Well, or even as an option: one with a starter, another with keys in the ignition)))
The autopsy itself showed that the starter is alive o_O We only checked it at home, when we took it off after about twenty minutes in the cold)) We throw the body on minus hook plus - the first time nothing happened, perhaps the reason was that Dad did not press it well against the terminal, disassembled the engine, the brushes are alive, and he himself he is quite alive without visible breakdowns, in general, LIVE, he rubbed it all together, think, let me try again, this time he pressed it to the terminal and twirled it.
Now the question, the starter has not yet posed. but what is the reason for that. by all indications the starter is alive. Akkum is alive. There are no signaling devices. Where is the catch.
1. Disconnect the negative cable from the battery.
If the car stereo is equipped with a security code, before disconnecting the battery, make sure you have the correct combination for putting the audio system into operation!
2. Remove the storage battery and the pallet of its fastening from the engine compartment (see Section Checking the condition and replacing the battery). 3. Disconnect the lower radiator hose and cable harness from the starter mounting bracket. On V6 engines, the ATF coolant lines run close to the starter mount - make sure they are pushed to the side.
4. Carefully mark and disconnect the electrical wiring from the terminals of the starter traction relay. Release the intermediate retaining clips of the electrical wiring.
5. Give the mounting bolts and remove the starter.
6. Installation is carried out upside-down.
Disassemble the starter as shown at the beginning of this procedure.
Check the collector diameter. If the diameter is less than the working limit, replace the armature.
Check the runout of the manifold (A).
If the manifold runout is within the operating range, check the manifold for coal dust, or remove any debris from the gap between the manifold plates.
If the runout of the collector is out of the working range, replace the armature.
Checking the depth of mica insulation (A). If the mica sticks out too much (B), trim the mica with a hacksaw blade to a normal depth. Cut off all the mica (C) to the specified depth between the manifold plates. The kerf must not be too shallow, too narrow or V-shaped (D).
Measure the length of the brushes. If it is outside the working range, replace the brush holder assembly.
Make sure there is no electrical connection between the (+) terminal of the brush holder (A) and the (-) terminal of the brush holder (B). If there is continuity, replace the brush holder assembly.
While holding the pinion gear, turn the pinion shaft counterclockwise. The pinion shaft must rotate freely. If the pinion shaft does not rotate smoothly without binding, replace the pinion cover assembly.
Place the brush in the brush holder and insert the armature (A) into the brush holder (B).
NOTE. To install new brushes, insert a strip of # 500 or # 600 sandpaper, abrasive side out, between the commutator and each brush and slowly rotate the armature. The contact surface of the brushes will be milled along the contour corresponding to the diameter of the collector.
Squeezing the spring (C), insert it into the hole in the brush holder and push it down until it stops. Repeat this step for the other three springs (D, E, and F).
Install the armature and brush holder into the stator housing.
NOTE. Make sure the armature is properly seated in the brush holder.
A specialized technical center offers inexpensive repair of Honda starters of any model. We will provide a long-term guarantee for all works. We have a full range of spare parts for all starters, so you don't have to wait long for the job to be completed. Fault diagnostics free of charge. We also offer to buy a new or remanufactured starter for Honda. Exchange is possible, which will speed up the repair time.
All work is carried out by qualified specialists.
REMOVAL AND INSTALLATION OF UNITS IS CARRIED OUT IN OUR SERVICE
The total cost of repair work for Honda starters is usually determined after diagnostics and detailed troubleshooting of the starter. The price of work is 500 rubles for any breakdown.
Repair: usually occurs within 1 hour, provided that the unit is removed from the car.In our workshop you can also use the service of removing and installing the starter. There is a large base of spare parts in stock. (Bendixes, retractor relays, armatures, stators, brushes, bearings, bushings).
Repair stages:
Your unit is checked on a diagnostic bench, for example, the operation of the electrical and mechanical parts of the unit.
If the unit is faulty, it is disassembled, a defect is done, thereby identifying the faulty units.
After troubleshooting, the cost of repairing the unit is announced. If the repair is not cost-effective for you, you can purchase a new or remanufactured unit from us.
Repair cost: determined after unit diagnostics.
The warranty for the work performed is 8 months.
Work experience 12 years. Was born in the Kaluga region. Education: Moscow Automobile University. Specialty "Auto electrician"
Work experience 7 years. Was born in Moscow. Education: Moscow Automobile College 76. Specialty "Auto electrician"
Work experience 7 years. The Krasnodar Territory was born. Education Krasnodar Automobile College. Specialty "Auto mechanic"
Removal and installation of a starter
1. Disconnect the negative cable from the battery.
If the car stereo is equipped with a security code, before disconnecting the battery, make sure you have the correct combination for putting the audio system into operation!
2. Remove the storage battery and the pallet of its fastening from the engine compartment (see Section Checking the condition and replacing the battery). 3. Disconnect the lower radiator hose and cable harness from the starter mounting bracket. On V6 engines, the ATF coolant lines run close to the starter mount - make sure they are pushed to the side.
4. Carefully mark and disconnect the electrical wiring from the terminals of the starter traction relay. Release the intermediate retaining clips of the electrical wiring.
5. Give the mounting bolts and remove the starter.
6. Installation is carried out upside-down.
Replacing a starter with a Honda Accord is done only if it is not possible to repair a starter on a Honda Accord or it will cost more than replacing a new one.
First, we will make a diagnosis starter Honda Accord, without removal. If the diagnostics show a problem in the starter, we remove the starter and put it on a special stand for diagnostics.
After taking readings, the master will produce disassembly and troubleshooting... After determining the cost of repairing a Honda Accord starter, a decision is made on what is best to do: repair and replace the starter with a new one.
Service station on Grazhdanka - 603-55-05, from 10 to 20, no days off. Service station in Kupchino - 245-33-15, from 10 to 20, no days off. WhatAapp / Viber: 8-911-766-42-33
ATTENTION. We do not repair starters removed from a vehicle. We independently make diagnostics, make a diagnosis and give a guarantee that the problem is in the starter and that we will solve it.
When to replace or repair a starter: - the car does not start, the starter does not show signs of life; - when trying to start the car, noise is heard, the car will not start; - after starting the engine, the starter is not disconnected;
