Do-it-yourself cheap wall repair

Repairing walls in an apartment is a rather complicated procedure that requires diligence and accuracy. A wide variety of finishing materials allows you to choose an option that is suitable for both cost and quality. Different coatings will help create an attractive interior in the rooms. This article will look at how do-it-yourself wall decoration is done and what materials can be used for this.

DIY wall repair is carried out in stages:

• assessment of the condition of the walls;
• removal of old finishes;
• elimination of various defects;
• leveling the surface.

After all these actions, the walls in the apartment are finished with new materials.

Often, when purchasing apartments on the secondary markets, you can run into strongly curved walls. The curvature of surfaces can reach 15 cm. In this case, it is almost impossible to repair old walls, and even unnecessary. It would be better to completely get rid of the plaster, which will save materials and expand the space of the room.

In addition, any work on wall decoration can be carried out only if they are of high strength. If the plaster is outdated and is moving away from the surface in some areas, it would be better to get rid of it. To test the strength, it will be enough to tap the wall with a mallet or other tool.

If a dull sound is heard or slight vibration is felt, such trim should be removed.

The preparation of walls for repairs always begins with the dismantling of the old coating. Since there are a lot of finishing materials, each of them has its own nuances of removal:

• Wallpaper. Dismantling wallpaper is the simplest procedure, which does not require special tools. Problems can only arise when removing thin webs. They will need to be pre-moistened with water and wait until the moisture is absorbed. The wet coating is removed with a scraper or a regular knife. You can also use a special solution to dissolve wallpaper glue.
• Plaster. Various plastering solutions have become very popular. Regular plaster can be removed with a wet sponge, but the decorative mortar is protected from moisture, so you will need to use a construction scraper.
• Dye. Peeling trim can be removed with a knife. If the paint holds well, you will need to use a building hair dryer. After heating, the coating will easily come off the surface. However, a hairdryer must be used by a professional.
• Tile. To remove it, you will need to use a jackhammer or perforator. Since the cost of such devices is quite high, it is recommended to rent them.

Wallpaper removal procedure

Often, various damages in the form of cracks are formed on the walls. They can be found after removing the trim. To repair cracks, you will need to perform the following procedures:

1. Free the damaged area and clean it from dirt and dust.
2. The crack is wetted with water, a reinforced tape is laid inside and about 2 mm of putty mortar is applied.
3. The putty is applied to the crack until it is completely closed.
4. Drying time of the solution will be approximately 2 hours, after which the area is cleaned with a grinder or a bar.

During work, the putty should be applied not only to the damaged area, but also to the plastered coating near it.

To repair cracks in brick walls, you need to use a scraper, a block and a grout brush.

The building is insulated at the construction stage.To replace the insulation, you will need to remove not only the finishing materials, but also the plaster.

Do-it-yourself wall repair in an apartment is not complete without prior alignment. This process consists of the following steps:

1. First, a primer is applied to increase the adhesion level of the surface. Also, this treatment will strengthen the base and prevent the formation of mold or mildew.
2. Plastered walls. The mixture is applied in at least 3 layers. Drying time for each of them is at least 12 hours.
3. Plastering is carried out. It is this cladding that allows you to create smooth walls for further wallpapering, painting or other finishing.

To check the evenness of the coating, a 2 m rule must be applied to it. If the work has been done correctly, a gap of no more than 2 mm remains between the wall and the tool.

You can learn more about wall repairs from the following video.

You can also perform the alignment procedure using drywall. This method is becoming more and more popular as it avoids working with different mixtures. Therefore, you do not need to wait for each layer to dry and there will be much less pollution from such a procedure. Plasterboard sheets are used in the following cases:

• If necessary, internal insulation of surfaces.
• If the walls are too crooked.
• If you need to cover the pipes for repairs in the kitchen or bathroom.
• To create complex structures: arches, columns or niches.
• When repairs need to be completed as quickly as possible.

First, you need to identify areas on the surface where heavy objects will hang. These places will need to be pre-strengthened.

It is also necessary to correctly mark the placement of profiles. After marking, the installation of profiles and drywall sheets is carried out. This procedure is quite simple, but there are a number of essential nuances:

• Profiles with a width of 27 mm act as guides.
• The rest of the construction details are made from a profile with a width of 60 mm.
• Installation of large figured structures will require skills and experience from the employee.
• In areas where heavy objects will be placed, it will be necessary to install horizontal jumpers between the profiles and strengthen them. For this, a section of a profile is used, the width and length of which is 60 mm. It is installed using self-tapping screws at a given height. Strengthening the profile is carried out by installing a wooden beam of the required size. To ensure high strength, in addition to the horizontal lintel, it is necessary to install vertical profiles to which it is attached.
• Also jumpers should be installed at the horizontal joints of the material.
• If further plasterboard cladding is planned, it is recommended to install the profiles at intervals of 40 cm from each other. This will strengthen the structure, and the joints of the sheets will in any case fall exactly on the profile.

Plasterboard installation procedure

The interval between profiles should be measured from the center of one product to the center of another, and not between the edges.

Repairing a wall in an apartment can be done using various materials. The most popular ones are:

• wallpapers of various types;
• frescoes;
• decorative plaster;
• dye;

Some people think that wallpaper is a long outdated way of wall cladding, but this is not so. The possibilities of such coverage are simply enormous. Canvases with a variety of designs and patterns are updated every season. Most often, the following types of wallpaper are used:

• paper or non-woven;
• vinyl;
• washable.

A variety of coatings will allow you to choose an option according to personal preferences. Non-woven fabrics are of high quality and density, they can hide small wall irregularities due to their thickness. Paper coatings are inexpensive, but their durability is rather low.It is highly discouraged to use them for cladding in the kitchen or bathroom, since they do not have protection against moisture.

Vinyl and washable wallpapers are a good solution for wall cladding in your home. They have an average cost, but they are of good quality and moisture protection.

A fresco is a hand-made work that includes wall cladding with water-based dyes on not yet dried plaster. The only drawback of such processing can be considered a high cost, but its appearance will fully pay off all costs. The fresco is perfect for creating almost any style, especially for bohemian interiors.

Decorative mixes are a more modern way of cladding. The composition of such a plaster includes the following components:

• marble stone chips;
• synthetic additives;
• nylon fibers or cellulose.

Effect of decorative plaster cladding

Various additives can significantly change the result of wall cladding in an apartment, so the composition of the solution must be taken into account at the time of purchase.

Apartment renovation is rarely complete without paint. The combination of painted surfaces looks attractive and stylish. Designers often experiment with a palette of colors, creating unique interior paintings. The most popular options are to highlight one wall with an unusual shade or to paint the surface with a stencil.

As you can see from the article, wall renovation is an extremely important procedure. It is on the quality of this work that the possibility of further surface finishing will depend. With the help of the photos used in the article, it will be possible to see in practice each stage of the work.

Not everyone has the means to hire a construction team to do the renovation. In addition, people who are not always found on the ad will really do everything to their conscience. If you do not need a global remodeling of the premises, you can make cosmetic repairs yourself. This is a very fun and easy process. The main thing is to purchase everything you need, observe the phased work, do everything carefully and with heart.

Here's what you need to purchase before redecorating:

• Spatulas - wide and narrow;
• Primer;
• Putty (dry or ready-made);
• Wallpaper;
• Ceiling tiles and glue for them;
• Flat brush, rag;
• Skirting boards for floors and ceilings;
• Floor covering (linoleum, laminate);
• Roller with a long handle;
• Cuvette;
• Glue for linoleum (if you lay it);
• Film, scotch tape for covering furniture.

Move furniture out to make space. Place the things from the closets in large bags, bags and also transfer them to another room. If the cabinet is heavy, there is no way to turn it over to another room, disassemble it by carefully folding the components. If this method does not suit you either, move the cabinet away from the wall, cover it with a wide cellophane film on all sides, secure it with a stapler or tape.

After all unnecessary has been removed from the room, proceed to dismantling. Tear off the old skirting boards first. If they are made of wood, it is convenient to remove them with a nailer. If these are plastic skirting boards on screws, a screwdriver or screwdriver will help.

Now you need to remove the old wallpaper. Starting from the bottom of the wall, pick them up with a spatula and tear off. If in some places they are glued "conscientiously", soak a roller in hot or warm water, walk it over the old wallpaper. Wait 10 minutes and you can easily peel off the paper. You can use a special tool that also moistens the wallpaper, and then remove them without problems.

If this phrase scared you before, now you will see how easy and interesting it is to do. Pour the required amount of primer into the cuvette, lower the roller into it, remove the excess liquid product. Cover part of the wall with it, and then all the walls in the room.

The primer dries quickly. Within an hour you can start filling the walls.The putty can be bought ready-made - soft, in sealed plastic bags. This method is suitable for those who do not have a construction mixer, but have a car, since it is unrealistic to carry or carry such a large amount of heavy putty, and you will need a lot of it.

Can be purchased dry in paper bags. In this case, you pour some of it into a bucket, add water according to the instructions and mix with a construction mixer. If not, dilute the product in small amounts and mix with a spatula.

Let the putty brew a little and proceed to the next stage of work. Align the walls as follows: scoop up a putty with a small spatula, put it on a large one. Fill the entire blade of a large spatula with the product, attach it to the wall, spread the mass evenly over its surface. Do this until the section of the wall is flat.

Will tell you how to carry out these works and make repairs with your own hands, video. It clearly shows how to level, plaster the wall.

Watch a video lesson about plastering walls with your own hands: