Do-it-yourself lg washing machine repair

In detail: do-it-yourself repair of a washing machine lg machine from a real master for the site my.housecope.com.

In order to do it yourself repairing an LG washing machine, you need to familiarize yourself with its design features.

Modern household appliances are easy to use and highly reliable.

At the same time, regular loads lead to wear and tear of various components and assemblies.

Today on the market, you can easily choose a washing machine that is suitable in terms of cost and performance.

Before going to the store, it is advisable to read the reviews of people who already use this or that unit.

The next point to pay attention to is the maintainability of the machine.

Washing machine LJI is a complex electromechanical device.

Its functional diagram includes the following components and assemblies:

water filling system;
heating system;
laundry washing system;
water drain scheme;
linen spinning system;
drying system.

In each new model, the developers improve some system or several components.

In order to exclude premature repairs, when installing and connecting the washing machine, you must strictly follow the rules set out in the operating instructions.

When loading clothes for washing, you should adhere to the recommendations for the volume and texture of fabrics.

The LG washing machine is not subject to special operating conditions. It is designed for normal household use.

The quality of the water and the tap is quite suitable for use without prior preparation. The video shows a washing machine installed in a regular bathroom in a standard high-rise building.

Video (click to play).

For the convenience of users, the designers have developed an indication system about the state of the main units of the unit.

Long-term practice shows that if all units are in full working order, the machine may not work. The main reasons that arise during the washing process are well studied and can be easily eliminated.

Often, when you turn on the washing machine, there is a rattling and knocking in the drum. In addition to this, vibration may occur.

It is possible that small foreign objects such as a ballpoint pen or coins have simply fallen into the drum. You need to stop the washing machine and inspect the drum.

A similar effect occurs when the laundry is unevenly loaded into the drum. Or there is too much of it.

Repair in such a situation is not required, it is enough to evenly distribute the laundry in the drum cavity. The vibration may be caused by an unstable position of the feet. They need to be adjusted.

If the procedures done do not help, then you will have to fix the problem with your own hands.

The design of the washing machine is designed so that all overflows of water from one reservoir to another are made through sealed channels.

If water starts to flow to the floor, it means that in some place the connection of the hoses is loose. This happened at the junction of the hose with the tap, or the hose with the input to the washing machine.

In this case, you just need to tighten the couplings at the connecting points. Water leaks even when the drain pipes become clogged.

In general, they must be periodically cleaned and not brought to such a state where the leak turns into a problem. If cleaning does not work on your own, you need to call a plumber.

In the event that water does not drain from the washing machine, it is necessary to carry out preventive repairs to the drain system.

The first thing to check when this trouble occurs is the condition of the incoming water filter. It is possible that it is clogged.

The second reason that leads to this effect is a clogged drain hose. Sometimes he finds himself in a stifled state. The third reason is that the drain pump filter is clogged.

Carrying out work to eliminate the malfunction that has arisen, you need to act consistently.The video shows the cleaning procedures that must be performed carefully so as not to violate the integrity of the hoses.When performing repairs or preventive maintenance of a washing machine with your own hands, you need to know about those nodes that fail faster and more often.Among them are the following:

oil seals and bearings;

heating elements;

rubber transition hoses.

When another malfunction appears, you must act in accordance with the operating instructions. Focus on the signals that appear on the indicator.For convenience, you need to have in an accessible place a table with the decoding of these signals.Many years of experience show that following these recommendations, in most cases it is possible to establish the regular operation of the LG washing machine.If the knock when turning on the machine cannot be eliminated, then you need to call the master or do the repair yourself. The video shows the sequence in which the drum is repaired.Knocking or vibration during washing occurs because the bearings have worn out.Therefore, the main task during repair is to replace a worn out bearing with a working one.

Along with the bearing, the oil seal is always changing, which ensures the tightness of the drum. The most important operation in this case is to remove the bearing and install a new one.

And also replace the oil seal that protects the bearing from moisture.

When the washing process is delayed due to the slow heating of the water, you need to inspect the tubular electric heater. More often this element is called shortly - heating element.

Scale forms on it over time. In order to slow down the process of scale formation, various chemical preparations are used from among washing and special powders.

Practice shows that they help, but scale still forms, albeit at a slow pace.

The video shows how the heating element is removed and cleaned from scale.

Descaling can only be done mechanically using a metal brush. If, after repair, traces of rust are visible on the surface of the heater, it must be replaced with a new one.

Almost every housewife who does laundry has come across a situation where water flows out of the washing machine for no apparent reason.

In this case, the repair is reduced to finding the place of the leak and eliminating the cause. Very often, with regular washing, the tightness of the clamps at the fixing points is weakened.

If water flows exactly in this place, it is necessary to loosen the clamp, move it a little and fasten it again. It also happens that a crack forms in the hose.

In this case, there is only one way out - the hose must be replaced. Sometimes water leaks due to a broken door seal. The rubber gasket must be replaced or corrected.

Repairing a washing machine is always accompanied by nervous tension, hassle and excitement. Especially when it is done by hand.

In order to avoid unnecessary troubles, it is necessary to regularly perform preventive maintenance of the washing machine.

The video shows how the pump that pumps out water from the tank is cleaned. This pump must be cleaned after every wash.

In the same way, you need to clean and wipe dry the rubber seal between the drum and the door. Over time, deposits build up on the seal and it no longer performs its function.Experts recommend cleaning the detergent tray. If you follow these simple recommendations, then serious repairs to the washing machine will not be required in the coming years. Image - Do-it-yourself lg washing machine repair machine

One of the best helpers in the house is the washing machine. It facilitates the work of a woman, frees her at least from washing. If the family is large, then you have to wash every day to keep the apartment clean and the hygiene of its residents. Therefore, the breakdown of the washing machine is a real problem for a woman.

The entire wash is a heavy burden on her shoulders. And the hostess begins to wash all this linen and clothes by hand, wasting time and energy. And so every day, dreaming about a new washing machine or about how to quickly repair an old one. And there is no money for repairs.

What then is to be done? It is necessary to somehow get out of the situation. If the husband is with hands and head, then he will be able to independently find the cause of the breakdown and replace the faulty part with a new one. Today we will tell you about how to disassemble the Lg washing machine and any other model.

The brands of machines differ from each other in some peculiarities: washing programs, sizes, number of revolutions, but the principle of disassembling washing machines is the same.

For high-quality and quick disassembly, you need:

two screwdrivers, a thin flat and a Phillips screwdriver for unscrewing the fasteners;
round nose pliers or pliers;
awl;
hammer;
open-end and socket wrenches;
ticks;
nippers.

The internal parts of the device are protected from negative environmental influences by metal elements of the case: back wall, front panel, top cover.

To do this, lay the device on its side and remove the pump through the bottom, having previously disconnected the wires from it. To remove the drain pump, you need to loosen the screws and disconnect the clamps. To do this, press the latches with pliers and disconnect the drain hose and the pipe.

You need to disassemble the pump from the snail by unscrewing the screws on it. Remove dirt and mucus from the snail.

Pay attention to the impeller, rotate it on the shaft, whether it turns, whether it is damaged. If it is broken, replace the impeller with a new one.

Also check the rubber seals. If the gasket is cracked or torn, replace it. Next, pry the latch with a screwdriver and remove the motor from the coil. Remove the monolithic cross by warming it up with a construction hairdryer. Then pull the magnet off the shaft.

After that, clean all parts of the pump, remove dirt, check the bearing. Lubricate it. If broken, replace. Begin reassembly using the photograph taken before disassembling the drain pump.

So, we have removed all panels: front, back and top covers, control module. We will now show you how to disassemble the loading tank of the Lg direct drive washing machine.This work in the service center is the most expensive, because the machine must be completely disassembled. The bearing and oil seal are located at the rear of the tank. To find out if the bearing is defective or okay, rotate the drum by hand.If you hear a creak and a hum, then the bearing does not work, it must be replaced.As soon as you buy Lg, you immediately need to install the washing machine on a flat surface, adjusting it in level so that there is an even load on the bearings. If you see a leak in the back of the tank, then the oil seal has become unusable. Image - Do-it-yourself lg washing machine repair machine

To get to the bearing, you need to completely disassemble the drum. You need to replace the part with a new one of this particular model. You cannot take a bearing from other machines, because it will not fit. When buying it in a store, pay attention to the integrity and quality of the part.

Direct Drive, or Direct Drive, is a new technology used by the Korean firm Lg. Thanks to it, the life of the washing machine is longer, because it does not have a drive belt.

The machine is quiet. In washing devices of this brand, the motor is located at the back of the loading tank, and not at the bottom, like in other devices.

We told you how to disassemble the loading tank in order to replace bearings and oil seals, how to remove the drain pump from the washing machine, disassemble and clean it. Now you know how to repair the device so as not to pay a lot of money for a complete disassembly of the machine and its restoration.

To repair a LG washing machine with your own hands, you need to know well the design features of the washing machine and its main faults that occur most often.From time to time, many have a situation when the washing machine stops working normally. Modern units, including LG, have no problems with diagnostics and error detection. The fact is that the screen-display shows codes, each of which corresponds to a particular malfunction. LG washing machines have their own coding, deciphered in the attached technical documentation. It also provides practical advice on how to eliminate the resulting breakdowns.Explanation of the main fault codes for LG washing machines:Many problems that arise with LG washing machines can be solved independently, in accordance with the decoding of the codes displayed on the display. If the measures taken have not led to a positive result, it is recommended to perform a service test for a more complete diagnosis. Thanks to the information received, the repair of the washing machine can be done independently. Sometimes there are breakdowns that are not provided for by error codes. They also need to be able to identify and eliminate.Sometimes the washing machine does not react in any way when the plug is plugged into the socket: the indicator lights do not light up, the musical greeting does not turn on. The reasons for this condition can be very different. Some can be easily removed on their own, while others - only in a service center.

Why the washing machine does not turn on:

Lack of electricity is the most common cause. For various reasons, an automatic machine or an RCD is triggered. Possible outlet malfunction.

Defective mains wire. The serviceability of the washing machine's power cord is checked using a multimeter. If a problem is found, the cord is completely replaced or repaired. All connections must be made only by soldering.

Malfunction of the power button, which receives power after connecting to the network. To check its performance, a tester is also used, set to the buzzer mode. The machine must be de-energized, and the button itself rings in both positions - on and off. If it is in working order, the multimeter will confirm this with a characteristic sound. If a malfunction is found, the button must be replaced.

Sometimes the LG washing machine will not turn on due to a malfunctioning noise filter (FPS). This device is designed to damp the electromagnetic waves emitted by the washing machine that interfere with the operation of other devices. When the FPS fails, it no longer passes electric current through the circuit, as a result, the washing machine does not turn on. Serviceability checks are carried out using a multimeter. It is necessary to ring the entrance and exit in turn. If there is voltage at the input, but there is no voltage at the output, then the FPS is faulty and needs to be replaced.Sometimes the drum stops spinning in the LG washing machine. In this case, turn off the machine, drain the water, open the door and try to turn the drum manually. If the drum does not rotate, then it is jammed. This situation can arise for various reasons. For example, on LG top-loading washing machines, doors may open and catch on a heating element or other part.Sometimes the drive belt jumps off, which has to be replaced along with the bearing.The bearings themselves fail due to wear of the oil seal, which allows air and water to pass through due to the loss of elasticity. A foreign object may enter between the tub and drum and prevent rotation.When the drum is rotated by hand, but it does not rotate from the electric motor. The most likely reason is related to defects in the control modules. It is possible to solve the problem by resetting the program, but in more complex cases, the board needs to be repaired or completely replaced.Another reason may be the failure of the drive belt, due to breaks or loosening. Sometimes the brushes of the electric motor fail, and the motor itself turns out to be faulty under the influence of water leaks or voltage drops. More precise reasons for the failure of drum rotation are established only after disassembling the washing machine and diagnostics.After a certain time of operation, extraneous noises may appear in the LG washing machine, as well as uncharacteristic sounds in the form of a squeak, crackle and others. The main causes of extraneous sounds can be the following:Quite often, situations arise when, while observing all the established norms, regarding the amount of laundry, washing powder and settings, water is still drawn into the tank too slowly or not at all.In such situations, first of all, the presence of water in the system and its pressure, the position and serviceability of the valve for supplying water to the machine, as well as the condition of the water hose are checked. If everything is in order here, the washing machine must be freed from the laundry, disconnected from the power and diagnosed in order to identify malfunctions.The main reasons for the slow water supply:First of all, the correctness of the washing mode setting is checked. Some LG models have a no-drain mode option that may have been accidentally turned on. Next, the drain hose is inspected for kinks and blockages. If necessary, clean it, and at the same time check the siphon if water is drained through it.The reason for not draining the water can be a filter that is dirty and clogged with various objects. Draining is significantly hampered or completely stopped. A clogged filter often leads to more serious damage to the unit, therefore it must be inspected and cleaned regularly. In addition, some small items of clothing can get stuck in the pipe, obstructing the escape of water.A faulty pump, the sound of which becomes quieter in comparison with the usual mode, often becomes the cause of a violation of the drain. The machine makes a noise or hums, but the water does not drain. The malfunction occurs due to physical wear and tear of the pump, designed for 3-5 years of operation. Small objects leaking from the filter can jam the impeller.Sometimes all systems work fine, but the water is still not drained. The main cause is a blockage in the drain hose, which must be removed and cleaned. The second reason is associated with a pump that has exhausted its resource and is able to rotate only without water, dry. When water is supplied, it jams, power is lost, and it stops rotating.To avoid such situations, experts recommend taking a number of preventive measures:

Remove all foreign objects from pockets before washing.

The weight of the laundry loaded into the drum must strictly comply with the instructions, overloading is strictly not allowed.

Use only high-quality detergents in the right amount for washing.

We recommend using a stabilizer during washing. This will help keep your equipment safe from power surges and surges.

Water leakage in LG washing machines is one of the most serious malfunctions when you need to take the most urgent measures. Leaking water can not only flood the neighbors on the lower floor, but also damage the electronic parts of the unit. Therefore, if a leak is detected, the wash should be stopped immediately and the water drained.The water supply to the machine is completely shut off.The main reasons for water leakage in LG washing machines are:

A leak near the filter indicates poor tightening after cleaning, damage to the O-ring or thread.

Water appears mainly in the front of the machine and often spills out through the doors. This becomes especially noticeable during the spinning process. The cause of the malfunction may be a loose door or a damaged hatch seal.

If a leak occurs while draining the water, the leaking drain hoses must be replaced.

Leakage can occur due to a rupture of the inner pipe, depressurization of the connections, or a defect in the water pump. In these cases, water comes out centrally under the washing machine or closer to the front of the washing machine. If a leak is found near the rear wall, it is likely that the bearing or the sealing gland will fail.

When the flow starts with the water supply, the problem may be in the powder tray, which is clogged with detergent residues. It is possible that the inlet hoses and water inlets are also clogged.

The most difficult part of the LG washing machine is undoubtedly the control module. In case of failure, the control panel stops the execution of all functions of the washing machine. After all, this unit turns on and off the device, organizes the direct washing process, selects the mode, provides rinsing and spinning, at its command, the water is heated and cooled.Before you independently repair the control module, you must diagnose it. In case of obvious malfunctions, the machine does not spin the laundry normally, and the error code is not displayed on the display. The lamps located on the control panel at the same time or do not light up at all. Water is not drawn into the tank even if the required mode is set. The wash itself stretches for 3-4 hours in a row without stopping and switching to other modes. There are constant freezes of the device, there are difficulties with setting the necessary programs.These and other signs gradually cause the complete inoperability of the washing machine. If at least one of them is available, the question of urgent repair of the control module should already be raised. Self-repair is recommended only to those people who have knowledge and experience with electronic circuits. In case of incorrect actions, the module will completely fail, and with it some components of the washing machine.If, nevertheless, a decision is made to repair yourself, you must follow a certain procedure:

The module is cleaned of sealant.

It is then carefully removed from the compartment away from the transformer.

After removal from the electronic module, the remainder of the sealant is removed.

Further, repair work is carried out.

After repair, a protective varnish is applied to the board sections.

In some cases, the module is not completely removed, only the necessary area is cleaned from the sealant, which is then repaired.

The Korean company LG makes great direct drive washing machines. This technology really significantly increases the service life of the engine and moving elements. However, these machines are also characterized by specific malfunctions, noted by the specialists of the service centers as the most common. If you are the owner of an LG washing machine, then in 80% of cases you will have to deal with the malfunctions discussed in this article.

Experts from the world's leading service centers note the relatively high reliability of LG washing machines. The most "tenacious" unit of this machine is considered to be the engine, which breaks down only in one case out of 500 calls to service centers, and then in half of the cases, the cause of the module malfunction is a factory defect.Moving elements are also considered to be quite reliable, except for bearings, they are repaired more often.

What units of the LG washing machine break down most often? Let's list them:

a heating element;
pressure switch;
bearings;
wires and terminals;
drain pump;
filling valve.

Malfunctions of these most important units of the washing machine manifest themselves in different ways. It is necessary to carefully analyze the "symptoms" in order to more or less accurately diagnose the problem of the module even before disassembling the "home assistant". In particular.

Note! When diagnosing faults in the washing machine with your own hands, be sure to listen and take a closer look at its work at the stages of washing, rinsing, spinning and draining. In addition, read the user manual, any deviations from the norm should alert you.

To get to the heating element of the washing machine, you need to unscrew several fasteners that hold the back wall of the LG washing machine by yourself, and then dismantle this wall. Next, you need to pay attention to the lower part of the tank (near the very bottom). Two paired contacts with a screw in the middle should stick out from there, to which several wires go - this is the ten. We check the contacts with a multimeter, if its display shows a value less than 20 Ohm - the ten is faulty.

Removing the ten is easy. We unscrew the screw mentioned by us with our own hands, pry on the sealing rubber with a screwdriver and pull out the heating element from the bowels of the tank. We visually check the status of the module. Burnt teng rarely does not have any visually noticeable damage (usually these are burnt spots). In most cases, the heating element breaks down due to a layer of scale that settles on it. Also, a breakdown can be provoked by a voltage drop or water that gets on the contacts. The video guide will help you to correctly remove the ten.

Repair of this module of the LG washing machine is not possible, only replacement. It is necessary to purchase an original spare part from the manufacturer and install it in the tank of the washing machine, not forgetting to install the sealing rubber. In the process of installing the heating element, you need to be most careful about the sealing rubber of the heating element. To make it sit better in place, you need to lubricate it with a small amount of machine oil.

Important! If the sealing rubber of the heating element sits loosely in the bore hole, water from the tank will seep onto the contacts of the heating element and it will most likely burn out again in the near future. Be careful.

Washing machine electrical repair LG boils down to checking all the wires and terminals coming from the control module to all of its units. It's not just about checking all the wiring with a multimeter - it goes without saying. It is also necessary to carry out a visual check: torn clamps, fragments of wires without insulation, traces of burning and melting of contacts. All wiring problems that can be detected during the check must be resolved by replacing damaged conductors and terminals - this is the repair of the electrician.

It is not difficult to diagnose faults in the filler valve of an LG washing machine on your own, and it will not be difficult to repair this module with your own hands, if you act methodically, according to a pre-planned plan. Dismantling and replacing the filler valve with your own hands is carried out in the following order.

Unroll the washing machine.
The inlet hose, which is connected to the water supply at one end, is screwed to the inlet valve with the other end. We turn off the cold water supply by turning off the tap.
We unscrew the inlet hose.
We take out, check and clean the filter of the inlet valve, it may be clogged with dirt and the water does not pass.
If everything is in order with the filter, remove the top cover of the washing machine, unscrew the two screws holding the valve, disconnect it from the pipes.
Next, we need to check the rubber bands of the valve, in 90% of cases the problem is their wear and the inability to retain water in the future. If so, change the rubber bands.
If it's not about the rubber bands, then most likely the problem is in the control electrics of the valve. In this case, the entire valve must be replaced.

Read also: DIY shower tray repair

To the drain pump of the washing machine LG can be reached without even disassembling it. You just need to tilt the machine on its side, after that it will be possible to get close to the unit through the bottom. We check the drain pump sensor with a multimeter, if everything is in order, then the problem is in the unit itself. Next, we proceed in order.

Unscrew the lower part of the front panel of the machine.
We unscrew the fasteners securing the drain pump.
We substitute the basin, since water will flow from the unit during removal.
Disconnect the plugs and remove the wires with the sensor.
Disconnect the pipes, drain the water and remove the unit to the side.

Note! Before placing the clipper on its side, remove the powder cuvette as directed by the user manual, as water remaining in the cuvette may spill onto the control box and damage the electronics.

Once the drain pump has been removed, it is best to have it checked and repaired by a specialist. Only he can finally say whether the pump has really come to an end, if so, then you need to buy and install a new one. Assembly is carried out upside-down. The easiest way is to change the pressure switch (water level sensor) of the washing machine. If you manage to disassemble it correctly, then it will not be difficult to replace it yourself.

Bearing failures are a matter of time or a factory defect. The user can influence this process only by the intensity of the use of the home assistant. Bearing malfunctions must be repaired immediately, because if this is not done, the loose pulley can damage the tank and then repairs will be very expensive. In this case, the user manual will not help; you either need to contact a specialist or study specialized information.

Thanks to direct drive technology, which is implemented on most models of washing machines from the company LG, bearings, motor, pulley and other parts wear out much more slowly and last longer. Nevertheless, there are still cases of bearing failure, and this poses a problem for “self-repair lovers”. Not everyone knows how to properly remove the bearing from the drum, but to start doing this, you need to remove and disassemble the washing machine tank.

Bearing repairs must be done very carefully, using a special hammer with a bronze bump and a thin metal rod. It is necessary to pull out the bearing by striking its opposite edges. First, we place the rod on one edge of the bearing and strike it lightly with a hammer, then transfer the rod to the other edge and again strike it lightly. The procedure must be repeated until the old bearing pops out, then a new bearing can be put in its place.

In conclusion, we note that malfunctions of any module of the LG washing machine, you can try to fix it. Of course, even if you study the relevant technical information and expert advice, successful repairs are not guaranteed, but it is definitely worth trying, especially since in most cases you have to deal with typical breakdowns. If something doesn't work, you can read the washing machine repair manual.

Everything in life breaks down at some point, because something eternal has not yet been invented. This article will focus on repairing a washing machine. Depending on the manufacturer, operating conditions and many other factors, this moment will come sooner or later.

Washing machine device.

Our family has a LG washing machine, they bought it on the recommendations of several specialists. But the impeccable period of LG's work was not too long, the wife's “favorite” worked for a little more than 4 years.

Without finishing the wash, the machine stopped.

During the next wash, something shot inside and everything stopped. Attempts to restart the unit were unsuccessful. Disconnecting from all communications (power supply, water, sewage) and removing the back cover, it was clearly visible: water through the control hole of the oil seal, flowing down, fell on the electric motor connection connector - and something shorted. I had no experience in repairing modern washing machines, and such a “good” moment finally presented itself.

First of all, the electric motor rang (there is a 10-pin connector), everything showed that the “engine is alive”. But to see this part of the car, it had to be completely disassembled. As I later saw, the engine is mounted between the covers of the outer drum.

The washing machine stopped in this mode.

Removing the washing machine module.

For further disassembly, it is necessary to drain the water by opening the hatch at the bottom. On the right, there is a short, thin hose with a plug.

After checking the engine, it was necessary to examine the electrical part further. To do this, I removed the top cover, it is fastened with two bolts at the back. All the wires were outwardly in good condition, which means that it was necessary to remove the module (brains). It is fastened with latches on the right side, and with two self-tapping screws on the left, which are under the container for washing powder. In the photo, the module is removed.

Externally, the module was in perfect condition. Began to deal with it in stages. The entire printed circuit board is sealed with a soft compound on both sides.

Front panel for washing machine.

This way of finding the fault gave nothing. It was necessary to open the compound. I tried to do it from the open, visible side, but I realized that it would be very difficult to lift the board, and most likely impossible. I read on the Internet on the forums how to do it. It turns out that you need to do the autopsy from the side of the display, cut out the windows in the plastic with a knife or just a soldering iron, and I started:

I remove the display board - it is latched at the edges - and cut out the windows for verification, in the place where the circuit is examined.

Opening the washing machine module for repair.

I had to make several windows. Section after section stubbornly led to the processor. The reason for the failure of the module was in it. Further renovations just didn't make sense. It's easier to just buy and replace a module.

Again I “went” to the Internet for prices for modules. They turned out to be quite acceptable (in the region of 3 thousand). This is 60-70% cheaper than repairs in the service. I called the local craftsmen, in one place they offered a used one. (unrepaired) for 2.200 rubles, and bought it. I put it on and started a short wash (30 min.). The machine ran like clockwork again. Well, I sat next to me and didn’t allow the water to hit the connector again.

The oil seal had to be changed unambiguously, and at the same time and to look at the bearings (whether water got into them). The washing was carried out when checking the module with the cover removed, which means that it is no longer necessary to remove it. I remove the module again, disconnecting all the connectors and wires. I remove the pulley by unscrewing the bolt in the center (the thread is ordinary - right). Taking off the belt, just in case, I looked in which direction the letters were written in order to put it in the same way.

Removing the washing machine pulley.

The pulley can be removed without any effort.

Removing the loading door of the washing machine.

Remove the loading hatch from the front side. It is secured with two screws.

Remove the rubber bellows clamp.

After that, you need to remove the clamp that holds the large rubber sealing corrugation.

We remove the electrovalves for supplying water to the washing machine.

We remove the water supply solenoid valves. They are attached with two screws to the rear wall.

Removing the detergent container.

Remove the powder container and suitable rubber tubes.

Removing the upper front corner, for ease of repair.

It is imperative to remove the upper bar (corner), since you cannot pull out the drum with it. Next, you need to disconnect the lower drum mount, there are two of them.

Bottom fastening of the washing machine drum.

By pressing on the protruding antennae, they can be easily pulled out of the landing site. The picture clearly shows these antennae. Almost everything that connects the drum to the body seems to be detached.

Upper springs holding the drum of the washing machine.

Now the drum hangs only on springs. And it is advisable to do the next stage together.

Side weights of the drum of the washing machine.

Grasping the springs, we remove the drum from the machine body. The next step is the removal of loads, both top and side. It is better to remove the upper one before removing the drum (the weight will decrease).

Washing machine body with electrical wiring.

Only one building remained from the “washing machine”. The weights were removed from the drum, then we remove the retaining ring that holds the sealing corrugation (unfortunately, I did not take a picture).

Washer rubber seal and retaining ring.

There is a photo, but later, in which the corrugation and the retaining ring are clearly visible.

Drum of the washing machine without weights.

And already without loads I took the drum out into the yard, the weather allowed. Next, the upper drum must be disassembled. It consists of two halves, which are connected in a circle with self-tapping screws. These halves are connected hermetically, since there is water in this drum during washing.

Inside the plastic drum is another drum, or stainless steel tub for laundry. Now you can see why the oil seal leaked and in what condition it is.

Washing machine drum cover with bearings and oil seal.

The photo clearly shows that during washing, the iron drum rubbed (clung) to the oil seal and damaged it. I must say right away that during the wash, the washing machine made a quiet creak. We did not pay attention to this sound, especially since it appeared at the very end of the wash.

The drum lid is cracked.

Now everything was clear, it was rubbing on the oil seal. The gland itself was removed from the seat without any effort. Having put this detail in order, I saw that on this cover around the gland there were cracks, so far barely noticeable, which means that there is a high probability that the process will go on and then the drum itself will flow. In the photo, I indicated these cracks with arrows. The bearings were in excellent condition and no water got into them. He began to put a new oil seal, but he "did not want" to sit in his nest. Painfully, this question was not finalized by the designer. And I decided to glue it.

Refinement of the inner side of the drum and replacement of the oil seal.

For this purpose, I bought a Dyson sealant, which has no equal from silicones (from experience). He put the gland on the glue, and at the same time filled the nearest sinuses with glue. I did the same procedure on the other side.

Reinforcement of the outer side of the washing machine drum.

I think it will add some rigidity to this part. I also improved the drainage. I inserted a tube of a suitable diameter into the hole and fixed it on the drum lid with the same glue.

Installation of drainage from the control hole of the stuffing box.

See how it turned out.

Then he assembled the washing machine in reverse order.

Video (click to play).

And now it works, even, it seems, a little quieter. The repair turned out to be simple, it cost me 2,650 rubles with glue and replacement of the oil seal. In our workshops, one replacement of an oil seal or bearings costs 3,500 rubles, and I also changed the module. I think that for those who want to take the risk of repairing their washing machine themselves, the article will somehow help in this. For repairs you need a Phillips screwdriver, keys 10, 17 and desire. Good luck to you!