DIY washing machine repair ariston margarita 2000

When a malfunction is detected in the Ariston Margarita washing machine, the controller rotates clockwise. The ON / OFF indicator flashes and indicates an error code.

We look at the blinking indicator and count the number of blinks.

For example, error F02 - two series of flashes with a frequency of 1 flash per second and with a pause between bursts of 4 seconds.

Decoding and troubleshooting error codes Ariston Margarita

But sometimes, the error itself is not shown. For this, there is a diagnostic key that is inserted into the board connector and starts a service check. Not everyone has this key, so we will not dwell on the methodology.

Remove the top cover, unscrew the panel fastening screws, dismantle the detergent drawer as shown in the figures.

Removing the command device will not be too difficult. Pick up the handle with a thin screwdriver and remove it. Next, unscrew the fastening screws.

Removing the cuff and replacing it if necessary - pick up the spring clip with a screwdriver and remove it. With the tool on top, unscrew the inner clamp screw.

The service life of Margarita, if used correctly, is 15 years or more.
This is explained by the build quality (Italy), reliable element base (mechanical control type)!

• The EVO-I based control module is used:

The software in the processor ROM is written once at the factory.

In case of breakdowns in the microcontroller, the board must be replaced.

The models differ in the type of "flashing" non-volatile memory (EEPROM) chips, which can be flashed in case of failures.

• Replacing the EEPROM memory chip:

Of course, you must first make sure that the actuators are in good working order and call them with a tester.

It is necessary to carefully examine the suspicious microcircuit. Unless, of course, we do not count the cases when the defect is already obvious (a bursting case, the presence of carbon deposits on the terminals, etc.), sometimes external damage can be insignificant.

Lack of short circuit on power supply. Sometimes there may not be a complete short circuit, but simply a very low resistance of the input (s) of the power supply relative to the “common” one. In this case, you will need to have the documentation for the microcircuit itself or at least the switching circuit available.

Functionality check. Here everything is much more complicated: many microcircuits have many outputs and a malfunction of at least one of them can lead to the inoperability of the entire device.

In the EVO I module, we replace the memory chip with a similar (93C86) serviceable one with uploaded firmware for the desired model.

Now about the most vulnerable places (due to high wear and tear and improper operation):
drain pump, motor brushes, water inlet valve, bearing assembly, heating element.

Washing units of the Ariston brand are very popular among consumers. The manufacturer of this technology is an Italian company that is a leader in the household appliances market. One of the most popular models is Ariston Margarita 2000. It is distinguished by functionality, reliability, high quality of washing. The breakdowns that occur with this device are typical for Ariston washing units and do not require special skills to be eliminated.

Thanks to the versatility and high quality of the washing machine, users note an excellent result at all stages of washing. The unit is economical in terms of water and electricity consumption.Users note the presence of convenient programs for the device. So, for washing delicate items, it is recommended to run the "Golden Cashmere" option. If you need to freshen up a small amount of colored laundry, use the daily wash option.

Switching on the washing machine

For medium-soiled items, we recommend using the Quick Wash cycle for 90 minutes. If it becomes necessary to postpone the start time of the unit, Ariston Margarita 2000 (ALS88X) will allow you to do this by pressing one button.

Front side of the washing machine

Turning on the machine for the first time, the user sees that the indicator, denoted by the letter "A", is on. This means that the device is in standby mode and ready for use. To select the required option, turn the knob and stop it near the inscription with the required program. At this moment, the indicator will switch to the letter "B", which tells the user that the device is ready to complete the task. After the final choice of options and operating conditions, the indicator will switch to the letter "C". The machine will start.

If necessary, stop the device, turn the program knob to the reset position. To set the deferred stratum, set the handle to the "KA" indicator and press "Reset". The machine will stop working for 5 seconds. To extend the time, select a suitable indicator on the display.

Any malfunctions of the Ariston Margarita 2000 (ALS88X) washing machine will not go unnoticed by the user. In the event of an emergency, the indicators on the unit flash and the control handle rotates randomly. You can determine what exactly is out of order by the nature of the blinking of the indicator.

The most common breakdown codes are:

• If the indicator blinks once at a certain frequency, then the wires in the electric motor are shorted.
• Blinking of the indicator 2 times indicates a malfunction of the tachometer.
• 3 times - short circuit in the temperature sensor.
• 4 times - the pressure switch is faulty.
• 5 times - there was a need to clean the drain pump.
• 6 times - error
• If the indicator flashes 7 times, the heating relay is stuck.
• Blinking 8 times at periodic intervals means the heating relay is malfunctioning.
• Blinking 9 times means a software error.
• 10-fold - pressure switch malfunction.
• 11-fold failure of the drain pump.

For a more accurate determination of the nature of the malfunction, the service center specialists connect a dongle that connects to the computer. As soon as the red indicator on the control unit comes on, the duty cycle and self-test starts. During such testing, the wizard identifies any malfunctions in the device of the washing unit. The computer displays washing machine errors, bearing failure, which must be eliminated.

You can repair Ariston Margarita 2000 (ALS88X) with your own hands, following the instructions from professional craftsmen. Those breakdowns that occur most often are eliminated according to the recommendations of specialists.

If the sound of pouring water is heard on the left side of the unit, but no water enters the drum, it is necessary to check whether the mesh on the filter is clogged, whether the supply is open and whether the hose is working properly.

Operation of Ariston Margarita 2000 means careful handling of the unit. If the machine randomly drains and pours water into the drum, but the sound of the pump running is not heard, it is necessary to check the correct installation of the hose. According to the instructions, the drain hose must be located at a height of at least 60 cm from the floor level.

The operation of the Ariston Margarita 2000 washing machine is not difficult for the user. In the event of a malfunction, the unit signals the problem by flashing the indicator. The number of flashes corresponds to the error code, which the user can learn from the instructions for the unit.Repair of simple breakdowns can be done by hand. In difficult cases, contact a specialist.

Today we will perform the pump replacement operation on the Ariston ALS88XEU washing machine. Replacing the pump as a whole is not a difficult operation and even an inexperienced person can cope with it with their own efforts. To do this, you only need the tools, the desire and this guide at hand.

We change the drain pump on the Ariston Margarita 2000 washing machine, model ALS88XEU

To begin with, prepare the space around the car if the size of your apartment / house allows it. Remove all foreign objects from the floor. And worry in advance about a doormat and a basin or other container into which you can drain the water. The container should not be very high so that you can slip it under the car, but more on that later.

With this model, the pump can only be accessed from below, so the following manipulations will have to be done.

1. Pull the washing machine towards you and gently tilt it back
2. Push the machine against a wall or kitchen wall. Make sure the washing machine is stable.
3. Take a slotted screwdriver and pry the top edge of the bottom trim panel along its entire length.
4. After prying off the top edge, squeeze the panel with your hand at the bottom and pull it towards you.
5. Place a bowl under the pump filter, then open it by turning it counterclockwise. Use pliers if you cannot open the filter by hand.
6. Empty the water into a basin and screw the filter back
7. Next, take a Phillips screwdriver and unscrew the two screws that hold the pump snail.
8. Next, press down on the brackets with a screwdriver to move the snail out of place.
9. Now you need to remove all contacts from the pump. But first take a photo, so that later it is easy to put everything back.
10. Take pliers and disconnect the tube from the pump by loosening the bracket.
11. Turn the pump upside down and remove the three screws that hold the pump in place.
12. We are halfway behind and a new pump can be installed.
13. Reassemble everything in reverse order.

For clarity, see the video below.

Video instruction: replacing the pump on the Ariston Margarita 2000 washing machine, model ALS88XE

After completing the replacement, you need to check that everything works as expected.

1. Set the program to water inlet. Wait for water to appear in the drum.
2. Now turn on the drain. And make sure that the water starts to drain, and also be sure to look under the car. Make sure there are no leaks anywhere and all connections are tight.

The pump is replaced if the washing machine does not drain the water and the failed drain pump is to blame. There may also be other reasons for poor or no water drainage. Read about them in the article:

Produced when the washing machine is unable to drain water. For this, the drain system is disassembled partially or completely, depending on the complexity of the blockage.

It is produced in the case when the pump has received mechanical damage or its winding has burned out. The work includes dismantling the faulty pump and installing a new one.

The versatility of Ariston washing machines makes them popular among consumers. The common models SM Hoitpoint-Ariston and Margarita-2000 are distinguished by their ergonomics and reliability, however, even such a technique can break down.

It is important to distinguish between the main malfunctions of Ariston washing machines, to know the ways to eliminate and repair them with your own hands.

The service life of the machine depends on the operating conditions. In the event of a problem, the repair of the Ariston and Hotpoint Ariston washing machines can be done by hand.

Let's take a look at the most common malfunctions that appear in machines of this brand.

Blockage is the most common cause of CM malfunctions. It prevents the normal draining of water from the tank, as a result, the washing machine cannot go to the rinsing mode. At the same time, the drain pump hums loudly, running idle.

If the pump (drain pump) breaks down, the hum of the operating device is heard, but the water does not drain.You will not confuse a malfunction of the water intake valve with anything: even when the Ariston washing machine is turned off, water is spontaneously drawn, a characteristic murmur is heard.

As a result of exposure to hard water, scale forms, and the tubular electric heater (TEN) fails. Breakdown symptoms: the water does not heat up, the laundry is washed in cold water, or the wash program does not start at all.

If a hum and crackle is heard during operation in the spin mode, the bearings have worn out. You cannot continue to operate the machine, otherwise it will work for wear and tear. The problem with changing bearings is that the washer tank is non-separable.

How to disassemble the Ariston washing machine and fix a breakdown, read on.

A fairly common malfunction is wear and loosening of mechanical fasteners. For example, a sunroof door may not close due to a skewed or broken hook. If the door is not closed properly, you will not be able to start the wash.

More rare, but still possible breakdown. It appears due to high humidity, foam on the board, sudden power surges.

The control module is the "brain" of the Ariston washing machine, therefore, if it breaks down, any details of the CMA can refuse to work.

Washing machines Ariston, Hotpoint Ariston, Aqualtis, Margarita and other models are equipped with a self-diagnostic function. The system displays a malfunction code, decoding which, the user can understand the cause of the breakdown.

CM with the scoreboard or display will show the error code on the screen. Those models that do not have a display (like "Margarita 2000") will give an error by flashing indicators.

How to recognize a code without a scoreboard? For example, the F02 error will be displayed by the indicators as follows: the light blinked 2 times, pause, then again issued the code 2 times. The number of flashes depends on the DTC.

Let's list the error codes for CM Ariston: F01, F02, F03, F04, F05, F06, F07, F08, F09, F10, F11, F12, F13, F14, F15, F17, F18.

A short has occurred in the motor control circuit.

1. Remove excess moisture from the controller contacts.

2. Replace controller or motor.

The signal about the operation of the motor does not reach the electronic controller from the tachogenerator.

1. Check the tightness of the connections between the motor and the controller.

2. Check the rotor for blockage.

3. Measure the resistance of the tachometer winding with a tester.

4. Replace controller or motor.

Breakdown of the temperature sensor, "sticking" of the heating element relay.

1. Inspect the connections between the temperature sensor and the control unit.

2. Check the sensor with a tester. In the event of a breakdown, a replacement is needed.

Faulty pressure switch (water level sensor).

1. Make sure that the contacts between the sensor and the module are tight.

2. In case of a malfunction, it is necessary to replace the pressure switch or controller.

There is a problem with the drain pump.

1. Check the quality of the connections between the module and the pump.

2. Check the pump and pressure switch with a tester.

3. Remove any blockages.

4. Change the pump or water level sensor.

Control panel buttons error.

1. Inspect the wiring connecting the controller to the buttons.

2. Check the functionality of the buttons on the panel.

3. Replace the panel or control module.

1. Make sure the pressure switch is firmly connected to the module.

2. Check level sensor and heater.

3. Replace the sensor or heating element.

Malfunction of the pressure switch, problems with the heating element relay.

1. Inspection of the water level sensor.

2. Quality control of the wiring between the heater and the control unit.

3. Replacing the pressure switch, block.

An error (failure) of volatile memory.

1. Re-flashing the microcircuit.

There is no signal from the water level sensor.

1. Control of the wiring between the sensor and the control unit.

2. Checking the sensor and the unit. Replacing a broken part.

There is no signal from the drain pump.

1. Checking the pump and the quality of its connection to the controller.

2. Make sure the pressure switch is working properly.

3. Replacing the defective element.

Lost communication between the controller and the display module.

one.Make sure no connections come loose.

2. Replace the defective element.

Open or malfunction of the drying temperature sensor circuit (for the AVD and AVL line).

1. Inspection of the connections between the temperature sensor and the control unit.

2. Make sure the temperature sensor is working properly.

3. Replace the broken part.

Drying heating element does not turn on (for AVD and AVL line).

Breakdown of the drying relay (for the AVD and AVL range).

2. Checking and replacing the level sensor.

Microprocessor problems.

Knowledge of the device and circuit of the Ariston automatic washing machine will help determine the breakdown. The picture shows the location of the main nodes of the AGR.

Let's figure out how to do an independent repair of the Hotpoint Ariston washing machine.

Which parts are most likely to get clogged and what to check first:

• Drain filter. Open the front panel of the washer, after placing a container for draining water. The round piece on the right is the filter. Unscrew it and remove the debris.
  
• Sewerage and drain hose. Remove the hose and rinse under a high-pressure tap. Examine the place of its connection with the sewer, it is possible that debris has also accumulated there. It is necessary to thoroughly clean everything with special means.

If your actions did not lead to the elimination of the malfunction, you need to check the drain pipe.

• Make sure there is no water in the tank and dispenser.
• Disconnect all communications and electricity.
• Lay the clipper on its side.
• Below you will see a pipe from the tank to the pump.
• Squeeze the clamp between the tank and pump.
• Disconnect the clamp securing the branch pipe to the tank.
• Unscrew the pressure take-off chamber and remove the clamp.
• Remove the nipple, check for clogging.
  
• If the pipe is not in the best condition, you need to replace it; installation is carried out upside-down.

Checking the drain pump will help to verify:

1. Pull out the pump filter.
2. Start the Spin program.
3. Use a flashlight to look through the hole.
4. If you see that the impeller is spinning, everything is in order. If it stands still, a blockage has formed, or the pump has broken.

Removing the old pump (pump) and installing a new one will help the following:

• Lay the CM on the left side, having previously disconnected it from the network and communications.
• Unscrew the two screws at the front.
• Disconnect the hoses.
• Pull out the pump and unscrew the three bolts securing the pump shell to the engine.
  
• Replacement is done upside-down.

Measure the resistance of the filler valve with a multimeter:

1. The valve is located at the point where the Ariston washing machine is connected to the water intake hose.
2. Inspect the gaskets for damage.
3. Take a tester and attach its tentacles to the valve contacts. Normal readings are 30-50 ohms.
4. In the event of a breakdown, replacing the valve is simple: unscrew it from the washer body and install another, connecting all the connections. Watch the video for more details:

To get to the heater, you need to remove the back wall of the Ariston washing machine. The heating element is located below, as shown in the photo.

Before removing the electric heater, measure its resistance with a multimeter. An indicator of 1 Ohm indicates an open circuit, about 0 Ohm - a short circuit has occurred. A working device will show 25-30 OHM.

Apply the tester as in the photo:

If the part is defective, replace it. Video to help you:

It is not easy to change bearings with your own hands: you need to disassemble the machine and get the part correctly.

But if you solve the problem yourself, carefully study the instructions for the Ariston washing machine with vertical and front loading. Additionally watch the video:

The door of your washing machine may not close or lock. The problem may be that the door is skewed, causing the hook to not reach the hole. It is enough to tighten the side loops. If the tab-lock is worn out, or the handle on the door is loose, only replacing the elements will help.

How to remove the control box:

• Unplug the power supply to the machine.
• Remove the top cover.
• Pull the dispenser out by pushing the latch in the center.
• Unscrew the front panel.
• Release the clamps and disconnect the board.
• Take out the selector and put a new board on it, and then reassemble in the reverse order.

Installing a new unit is not difficult. It is more difficult to repair and clean the contacts. If you decide not to call the master, but to carry out the work yourself, watch the video:

Having understood the main causes of malfunctions of the Ariston washing machine, you can eliminate them yourself. Be attentive to detail and do not neglect safety precautions.

When doing repairs, you will need to make detailed disassembly and assembly of the washing machine. Therefore, in order to properly disassemble, assemble and repair the Ariston Margarita 2000 washing machine, you need to follow the disassembly procedure.

The top cover is latched to the control panel and attached to the back of the machine with two screws. To remove the cover, unscrew the two fixing screws and slide the cover back (Fig. 1).

1. Using a small screwdriver as a lever, separate the front door seal.
2. Having released the seal, put it inside the drum.
3. Tilt the machine back (under no circumstances lay the machine on its side, just tilt it, as there is a danger of water getting on the electrical connectors) and substituting some kind of stable support under it.
4. Use thin pliers to release the door ring (fig. 2).
5. Remove the seal.

The new seal is placed exactly on the flange of the tank, making sure that the seal is well fixed. The small tab at the top of the seal should point vertically (fig. 3).

Using a screwdriver, remove the spring ring that secures the sealing rubber to the body and remove the sealing rubber of the door. Use a Phillips screwdriver to loosen the two screws. Having assembled a new part, the sealing rubber is installed in its original place.

1. Remove the top cover.
2. Remove the handle and the cover of the controller (KA).
3. The screw is unscrewed from the KA handle and the KA mechanism is removed.
4. Opening the detergent dispenser drawer, press down at the point shown in fig. 4, and the drawer is removed.

1. Remove the two loading door screws and the two control panel screws.
2. Remove the potentiometers using a Phillips screwdriver.
3. Pry off with a screwdriver and release the pushbutton switches.
4. Remove the pushbutton switches, remove the ON / OFF indicator and the door lock indicator.
5. Unscrew three screws fastening to the KA panel and separate it.

When assembling, all operations are performed in the reverse order.

1. Remove the top cover.
2. After removing the handle of the controller, remove its mechanism (see "Control panel").
3. Disconnect the terminal block of the controller.
4. Having released the latch on the program disk (Fig. 5), the command device is moved up.
5. The command apparatus is removed by moving it inside the machine.

When installing the controller, make sure that its guides are correctly aligned with the support panel (Fig. 6).

The rest of the spacecraft installation operations are performed in the reverse order.

1. Remove the back panel.
2. Unscrew the screws securing the module and remove the module.
3. Disconnect all connectors and terminal blocks.

1. Remove the screws that secure the frame and handle subframe.
2. Remove the handle base from the casing.
3. Replace the handle.

When replacing the handle, all operations are performed in the reverse order.

Using a 13mm socket wrench, unscrew the two nuts and remove the counterweight (fig. 7).

After removing the washing machine tank, unscrew 8 screws and remove the counterweight (fig. 8). When removing the counterweight, you can pry it with a screwdriver at the points of attachment to the tank.

1. Remove the back panel (item 23, fig. 16) and the drive belt.
2. Using a socket wrench, unscrew the screw from the pulley, keeping the pulley from rotating (Fig. 9). It should be borne in mind that the screw is set on the sealant, and it is not easy to unscrew it.

1. Using two screwdrivers as levers, the pulley is removed.

For a more secure tightening of the screw, it is recommended to apply a drop of Loctite 270 to the screw thread.

You can turn on the washing machine no earlier than three hours after installing the pulley.

1. Remove the back panel (item 23 fig. 16).
2. Tilt the machine forward with some kind of stable support. Care must be taken not to damage the electrical components of the control panel and micro locks.
3. Remove the drive belt.
4. Disconnect the electric motor. To do this, take out the terminal block and disconnect the ground wire (Fig. 10).

1. Unscrew the two 8mm hexagon head screws.
2. The electric motor is lowered and removed from the machine body through the open rear panel (fig. 11).

Three rubber parts and two plastic feet are used when installing a new electric motor.

The operations for installing the electric motor are performed in the reverse order.

1. Remove the back panel and remove the electrical connectors.
2. Using a screwdriver, remove the sensor pos. 7 (fig. 12)

1. Unscrew the 4 screws (if there is only one screw, then after removing it, turn the pump casing).
2. Disconnect hoses and tubes.
3. Install a new pump.

1. Carefully tilt the machine to the side (do not lay the machine on its side).
2. Using a 10mm socket wrench, unscrew the nut that secures the shock absorber to the body (Fig. 13).
3. Pushing the shock absorber along the rod, it is pushed out of the machine body.
4. Using two wrenches, 17 and 15mm, loosen the screw that secures the shock absorber kit. Remove the shock absorber.

When installing a new shock absorber, all steps are performed in the reverse order.

1. Remove the top cover, rear panel, control panel, water filling unit with solenoid valves, pressure switch, door seal on the side of the body, drain pump, shock absorbers and disconnect all electrical components and parts (resistors, electric motor, etc.). When disconnecting the connectors, sign and label them)
2. Remove the tank from the body and place it on the floor with the pulley up.
3. Dismantle the pulley.

1. With a socket wrench, unscrew 8 screws that attach the crosspiece to the tank (Fig. 14).
2. With two screwdrivers, grasping as shown in fig. 15, remove the spokes from the holes.

When installing the cross, use a rubber hammer to protect it from deformation and damage.

In fig. 16 shows the cabinet and decorative components of the AL109X washing machine. The list of components is given in table. one.

A good friend of mine bought this washing machine back in 2000. Then this unit was worth "big money". If you compare, it equates to 10% of the total cost of the apartment. The figure seems small, but believe me with a salary of 4,000 rubles and 3 - their children "in the bosom" - this purchase was just a real feat. The car has served in excellent condition to this day, but just a month ago, my friend suffered a lot. Because…

The washing machine has broken down. For so many years, no modern machine will work. She turned to me for help, I didn’t, but I had already begun to slowly understand the breakdowns. I also flew Bosch that year. I advised her to contact her home appliance repair company Stirrem. ru .

Honestly, my friend was very pleased with the results. Literally on the same day, they came to her and took the car. It was very attractive that the friend did not pay at all for calling the master to the house, and they also carried out the diagnostics free of charge. Here are the things here. Therefore, if my "baby" breaks down, I will only trust the craftsmen of the Stirrem company. ru.

For 10 years already, Stirrem. ru, pleases its customers. The company helps in the field of household appliances repair and maintenance. Among the population, there is a legend that the masters of Stirrem. ru are able to cope with any breakdown. We are not ashamed to say - this is the pure truth. The fact is that the specialists of our company are tested in 2 stages:

The first is when applying for a job (most candidates at this stage are eliminated immediately)

The second is for follow-up. The probationary period is 2-2.5 months (at a rate of 1 month!)

In favor of our company is the fact that we do not charge for the departure of the master, as well as for the diagnostics of the unit (the fee is charged only if there is no repair to be done). Imagine - that's a pretty big plus!

In order not to bite your nails upon the arrival of the master and to briefly explain what happened, you need to know the most common types of breakdowns. Read about this and more below ...

By the way, washing Margarita 2000 cars very durable. With proper care, they can last 6-7 years. The main breakdowns of Margarita 2000 are: wear of the heating element (heat-heating element), bearing or oil seal. You can find out more detailed information here ...

In this case, we recommend that you disconnect the machine from the power supply and wait for the arrival of the master. Possible cause: A solid object has fallen into the drum compartment.

We kindly ask you to disconnect the washing machine from the socket! If this is not possible, then turn off the electricity through the house shield and wait for the arrival of a specialist. Possible reasons: wear of the filling / drain pipes, leaking tank, damage to the collar of the drum hatch.

Perhaps your drive belt is torn or the control system program is out of order. Call our master and wait for his arrival.

The most dangerous of all breakdowns. Be careful! When you first detect this kind of malfunction, immediately call the wizard. Possible cause: Incorrect grounding of the device or its installation.

Most likely your heating element has burned out. Only a specialist can replace this device. Call our phone and wait for the arrival of the master.

The reason most likely lies in the breakdown of the on / off button. It is not possible to make such repairs on your own. Wait for the arrival of our master.

I would like to add a few words about the Margarita 2000 brand. This washing machine is the "brainchild" of the Ariston company. The car was designed to meet the needs of ordinary buyers. As a rule, it is distinguished: durability, simplicity and economy. For some people, this machine works for years. And for those who are unlucky, we ask you not to get upset and offer the following ...

To quickly and efficiently repair the irreplaceable "helper". There are various promotions and discounts especially for you. More details about the cost of services here. We are pleasantly surprised - we are trying! You can easily afford it.

All our services have a long-term guarantee (you can take a warranty card from the master). If you have any questions, you can call the hotline right now.

Washing machines "Ariston" are well known to modern consumers and are in incredible demand. These devices are manufactured by the Italian company Merloni Elettrodomestici S.P.A., which is the leader in the domestic market. The model range of this brand is headed by the multifunctional and high-quality washing machine Ariston Margarita 2000. Its malfunctions can be called typical for units of this line, so you need to get acquainted with the most common of them in more detail and consider options for their solution. What we will do in this article.

Models of this series have a wide range of functions and are distinguished by sufficiently high quality indicators of washing, rinsing and spinning, consume a minimum of electricity and water. They belong to the A class of washing, because even if the water is heated to 40 degrees, they consume only 0.15 kilowatts of electricity per kilogram of dirty laundry.

This washing machine is equipped with a rather interesting program called "Golden Cashmere", which allows you to wash only delicate fabrics and avoid pilling.But the function of everyday washing assumes a cycle time of only 30 minutes, while you can load items of any color into the drum.

A quick wash in just 90 minutes removes moderately soiled items. If desired, you can postpone the start of operation of the Ariston Margarita 2000 device for the required time. Malfunctions rarely occur in its work, but they all require attention and, in most cases, the intervention of specialists.

Initially, the machine is in the standard standby mode, indicated by the “A” indicator, and to start the desired program, you need to use the special command handle.

The indicator in the “B” mode indicates that the device is ready to receive a new program, and as soon as it is selected, it will be indicated by the “C” indicator. And immediately after that, the washing begins. Its execution can be stopped, and for this you need to turn the program knob to the reset position.

To stop the countdown, you need to set the handle to the “KA” position and press “Reset”, it will stop for five seconds. But if you need more time, then select the required amount on the display. And the machine will be in standby mode for all the specified time.

If a malfunction was detected in the operation of the Ariston Margarita 2000 washing machine, then the on / off indicator immediately starts blinking, and the command handle will rotate randomly. The flashing pattern of this indicator indicates a fault code.

The most common trouble codes are:

1. A short circuit has occurred in the motor circuits.
2. Communication with the total stations has been cut off or the electric motor has jammed.
3. There was an open or short circuit in the temperature sensor.
4. The pressure switch is stuck in the “Empty” position.
5. The relay is stuck in the “Unit full” position, or there is a blockage in the drain pump.
6. An error has occurred in the control function.
7. The heating relay is stuck.
8. The heating relay has stopped working.
9. The model is not compatible with EEPROM.
10. The relay responsible for pressure began to simultaneously send signals that the device is “Filled” and “Empty”.
11. The drain pump is out of order.

Important! To more accurately determine the malfunction, specialists use a special tool, namely a hardware key. It can be connected to a computer and initiate a wash, during which the machine will perform a self-test. It is inserted into a special hole on the back of the device. If everything is done correctly, then the red indicator on the block will light up, that is, it will be possible to start self-testing.

Do-it-yourself repair of the Ariston Margarita 2000 washing machine is recommended only if there is a special service test. It allows you to easily detect any defect in the operation of the device and make repairs faster and easier. Next, we'll take a look at how to run this test and check the machine's performance.

In order for the service test to work, you need the aforementioned key to perform SAT diagnostics. This tool has the following code - 95669. It allows you to run the automatic testing program for the Margarita 2000 model. Then we connect the device to the connector and wait until the corresponding indicator lights up. First, the key will exchange information with the electronic controller for some time.

The testing program is launched as follows:

1. We check the connection of the machine to the water supply and sewerage system.
2. We inspect the tank for the presence of water residues in it, if there is, then it must be removed immediately.
3. Close the hatch door tightly.
4. We set the selector knob to its original position.
5. Press the “AUTO TEST” button on the key and hold it.
6. As soon as the automatic testing starts, you will immediately hear a beep.

Important! During testing, the selector knob will automatically rotate, and at the same time, codes of the corresponding nature will be displayed on the panel. If the test detects an error, the indicator will stop constantly glowing, and the lamp will start blinking flashes, that is, indicate a malfunction code.

The number of flashes indicates the error code. Please note that during testing, the water inside the device will heat up to 30 degrees, so you need to set a water heating limit, turn off the spin functions and set any drying time.

The diagnostic process of the "Ariston Margarita 2000" washing machine can be conditionally divided into several stages. Malfunctions and possible breakdowns are eliminated in the following sequence:

1. The wash inlet valve in main mode is selected and started for 10 seconds.
2. Then a pre-wash is started for the same time in the same mode.
3. The hot water supply valve opens for 10 seconds.
4. The inlet valves for the main and preliminary washings are switched on simultaneously. Water will flow into the tank until the sensor gives a signal that it is full.
5. The drum rotates first clockwise and then in the opposite direction.
6. The heating element turns on and the water heats up to 30 degrees.
7. The handle moves in the normal direction of rotation and then stops at the 9th position.
8. The drain pump starts working. Moreover, it will function until the sensor reports that the tank is empty.
9. If the device is equipped with a drying mode, then its fan will start working at this stage, and then the heating element will turn on and the air inside the tank will begin to warm up.
10. The selector handle moves to the reset position.
11. The program ends its work.

Important! If the malfunction of the Ariston Margarita 2000 washing machine was eliminated even before the start of the test, then the service analysis simply will not start. To restart the machine in this case, you will need to turn it on for 10 seconds, disconnect the service key and start it again.

If you want to fix the problem yourself, you need to understand how the Ariston Margarita 2000 washing machine is properly disassembled and assembled. Malfunctions of this model are largely eliminated through its partial or complete disassembly.

Important! Remember that most problems with such equipment can be prevented by competent service, which, by the way, will not take much of your time. Just follow the rules outlined in the articles below:

The top cover can be removed quite easily, you just need to snap off the control panel and unscrew a few screws from the back wall. To remove the cover, you need to unscrew the two mounting bolts and simply slide the cover to the side. The screwdriver will help to gently remove the snap ring that secures the rubber seal directly to the body and the rubber seal on the door. The screws are removed with a Phillips screwdriver. As soon as the new part is replaced, the sealing gum returns to its place.

In more detail, this process looks like this:

1. The top cover is removed.
2. The cover and the handle are removed.
3. The screw is unscrewed from the handle and the mechanism is removed.
4. The detergent dispenser drawer is opened and removed by pressing.
5. The two screws of the control panel and the loading door are unscrewed.
6. The potentiometers are removed.
7. The push-button switches are removed.
8. The on / off and sunroof lock indicators are retrieved.
9. The control panel screws are removed.
10. The counterweight is removed using a socket wrench.
11. The tank is removed, all the screws holding the counterweight are unscrewed.
12. The back cover and drive belt are removed.
13. The bolt is unscrewed from the pulley, which prevents it from turning.
14. The pulley is removed with two screwdrivers.
15. Then we tilt the machine forward and support it with something, but you need to make sure that the electrical components of the lock and control panel do not fall out.
16. Disconnect the motor by pulling out the terminal block and disconnecting the ground wire.
17. The electric motor is lowered and pulled out through the already missing rear panel.

So, we examined the basic rules and the sequence for parsing this model of the washing machine. If you follow them, then the process of replacing a broken part will not cause any difficulties.

Do-it-yourself repair of the Ariston Margarita 2000 washing machine can be done if you follow the instructions below. The most common malfunctions of this device are eliminated as follows:

Important! There are also possible problems that you can easily solve by following the instructions from the articles below: