Do-it-yourself Samsung washing machine repair leaks

When buying a new washing machine, people rely on its long and trouble-free operation. But any household appliance has its own shelf life, and it is determined not only by the reputation of the manufacturer, but also by the correct operation. That is why many owners sooner or later face the fact that their washing machine is flowing from the bottom.

This is one of the most common faults. If water flows onto the floor, it doesn't matter if it drips or runs in a stream, an urgent need to repair the washing machine on its own or call a master.

If you prefer to troubleshoot home appliances yourself, this article will probably come in handy for you. Let us consider in detail the reasons for the leakage of the washing machine and the methods of its repair.

• Washing machine dispenser hopper clogged.
• Tank not sealed (crack or breakdown appeared).
• One of the hoses (drain or inlet) has been damaged.
• The pump is leaking.
• Tank oil seal worn out.
• The door rubber cuff is leaking.
• One of the pipes has lost its tightness.

Before starting repair work, you need to de-energize the equipment by removing the plug from the outlet. Then you need to figure out which of the many elements of the washing machine is leaking. To do this, the washing machine must be carefully inspected.

It is extremely important to find out the cause of the breakdown at what stage of the operating cycle the washing machine began to leak from the bottom. This will greatly facilitate the troubleshooting task and will allow you to detect 1 of 3 possible leak locations. Leakage locations such as:

Drain and inlet hoses for water often leak where they dock with the unit. To get rid of such a breakdown, you need to unscrew the hose for filling or draining water and change the rubber gasket.

But it also happens that the hose has worn out, or was accidentally damaged, then to restore its integrity, you can use a special glue and a rubber patch, although replacing it with a new one would be a more reliable option. But all of these recommendations are suitable for the drain hose. If the inlet hose has been damaged, we do not recommend repairing it with a patch, since the water pressure in it can be very high, and then replacement becomes the best option. You can buy a water inlet hose at any plumbing store, moreover, inexpensively.

The dispenser may be damaged if the hopper (i.e. powder compartment) is defective. As a rule, it leaks when it is clogged, either due to excessive water pressure, or due to a failure of the intake valve. What to do in such a situation?

If it’s a valve, you’ll see leaks in the area below it. To eliminate the causes of the leak, remove the dispenser and thoroughly clean it and the hopper. It so happens that a foreign object appears in the drain of the bunker, which does not allow it to work normally. If you find such an item, remove it from the powder compartment.

After cleaning, test the operation of the washing machine. In addition, it is worth trying to reduce the water pressure by slightly closing the tap. If none of the above helps to cope with the leak from the bottom, it is necessary to replace the inlet valve, since it is its breakdown that can cause the high water pressure during the rinsing phase.

It is not uncommon for many people to forget to remove all things from the pockets of their clothes before loading them into the washing machine, and many of them can be very sharp. As a result, the cuff on the door of the washing machine is damaged during the wash process and begins to leak.

In such a situation, you can fix the breakdown in one of 2 ways:

1. Repair. If the hole is small, try covering it with moisture resistant glue and a rubber patch. You can also purchase a custom boat patch from your fishing specialty shop. After sealing the hole, the hatch cuff should be installed in such a way that a piece of patch rubber is placed on top - this will reduce the pressure on it, and therefore increase its service life. Since the collar can also be damaged on the inside, we recommend dismantling it to seal the holes.
2. Replacement. If the damage caused is too great, a complete replacement of the cuff of the washing machine hatch will be required, for which you need to do the following: dismantle the faulty cuff and install a new one instead.

It is likely that the reason why water began to flow from the water supply hose is the weakening of the attachment of the nozzle to the tank of the machine. To find out if this is so, a thorough examination of the tank is required. If you see traces of water leaks, then the problem has been found.

To repair or replace the inlet hose of the washing machine, you need to remove the branch pipe, then clean all sections of the connections from the remaining glue and dry them. Then you can re-fix the branch pipe, for fixing which you need epoxy resin or high-quality moisture-resistant glue.

If you saw that it is the tank that leaks, there may be two reasons for such a breakdown, we will consider them in detail.

The buck is cracked. Tanks in automatic machines are most often made of plastic, which is why their reliability is rather low. If you forget to empty the pockets of your clothes, during the operation of the unit, one of the objects in them could fall out of the pockets and damage the tank.

If the tank is cracked, it will need to be replaced, which is a very expensive and complicated process. Of course, you can try to remove the crack yourself using waterproof glue, but this is unlikely to help you for a long time, because the tank will most likely need to be changed, and this will have to be done with the help of a specialist.

The joints of the tank parts. As a rule, the tank of the automatic machine includes 2 elements connected to each other by metal brackets or screws, and in the space between them there is a rubber gasket. Such pads dry out over the years and begin to leak. To change the gasket, the device must be almost completely disassembled.

See also -Do-it-yourself repair of a washing machine tank leak

If the washing machine leaks from the bearings, the reason is the wear of the oil seal, which means that you cannot do without replacing it. Most often, with such a malfunction, the main volume of water flows out during the spinning process.

If an oil seal leak is found, you must immediately turn off the machine, because due to water, the bearings can rust and also break, and this will lead to more serious problems.

Changing the oil seal is not easy for a layman, since the process will also require replacing the bearings of the washing machine. That is why we advise you to contact a professional to repair such a breakdown. If you still want to repair the unit on your own, before that you will need to understand how the bearings are replaced.

If you have been cleaning the drain valve not so long ago, it is possible that after the end of the procedure you forgot to carefully screw it in, and as a result, a leak has formed. Take out the bottom panel and make sure that the valve is screwed in completely.The main reason for the appearance of a leak in the washing machine is mistakes made during its operation. Therefore, in order to avoid such breakdowns, we recommend that you always check the pockets of your clothes before loading them into the machine, and promptly carry out repair work at the first detection of any malfunction.

Owners of home appliances of a well-known South Korean brand will be interested in how a Samsung washing machine is repaired with their own hands.

Unfortunately, sometimes it is necessary to eliminate breakdowns and leaks of washing machines, even in an expensive price segment, and knowledge of error codes and related malfunctions may also be required.

First, you should familiarize yourself a little with the main features of these machines. First, it is stylish design.

Secondly, it is the original design of the drum. Modern modifications of Samsung washing machines are equipped with a fundamentally new technical solution - Drum Diamond Drum .

It belongs to an innovative type of honeycomb drums with a surface covered with many convex pyramids and small water holes, into which the fabric is not drawn.

Thanks to this design, a gentle wash cycle is provided. These drums can be very spacious - with a load of up to 12 kg of laundry, depending on the model of the machine.

Thirdly, worthy of attention heaters with double ceramic coatingnot covered with limescale, and inverter motorattached directly to the drum in some modifications.

Also interesting are the functions Fuzzy Logic and Smart Check responsible for the correct calculation of the washing mode depending on the amount of loaded laundry, as well as for diagnosing various machine malfunctions.

The number of wash programs depends on the model of the washing machine. Even the simplest modifications are equipped with all the necessary set of programs, and the new models have a washing mode called ECO Bubble - with the help of air bubbles, laundry is easier to wash even in cold water.

If the machine is marked with Wf, it means that this model is front-loaded, and if its name contains the abbreviation WD, it means that the machine is equipped with a built-in dryer.

But Samsung brand machines also have one small drawback - their instability to voltage drops in the network, which is important in our Russian reality.

When the voltage becomes either too high or low, then a control system called Volt Control simply turns off the washing mode to resume it immediately after the mains voltage has stabilized. This is not always convenient, so it is better to connect the washing machine through a voltage regulator.

After a short acquaintance with the parameters of this brand, let's move on to considering the main breakdowns.

To understand the malfunction that has arisen, you need to consider the most common of them and the reasons for their occurrence.

Here is a list of common problems:

Further, the methods of repairing them with your own hands will be considered, because it is not always possible to call the master. And for this you need to have a set of necessary tools.

Before starting repairs, you need to make sure that all the tools from this list are available:

• flat and Phillips screwdrivers or screwdriver;
• set of wrenches;
• pliers, pliers, wire cutters;
• tweezers - elongated and curved;
• powerful flashlight;
• long-handled mirror;
• soldering iron;
• gas-burner;
• small hammer;
• knife.

In addition to the listed tools, you may need a magnet to pull out small metal objects inside the machine, a long metal ruler to align the drum, a multimeter or voltage indicator.

But that's not all. In addition to the required set of instruments, the following building materials will need to be purchased for repairs:

• sealant;
• Super glue;
• insulating resin;
• soldering materials - rosin, flux, etc .;
• wires;
• clamps;
• current fuses;
• rust remover;
• electrical tape and scotch tape.

Sometimes a multimeter is not needed, it is enough to turn on the machine and select a mode with a high water temperature. From the operation of an apartment electricity meter, it is easy to understand whether the heating element is receiving power.

If you are a beginner, then you can advise using a camera to shoot a video or to photograph a workflow, so as not to confuse the sequence of actions and then assemble the machine correctly.

There are several important rules to remember that must be followed before starting repair work:

• it is necessary to drain all the water from the machine;
• before disassembly, be sure to (!) disconnect the device from the power supply;
• choose a bright and spacious enough place for renovation.

If the unit cannot be moved to a convenient location, then ensure maximum illumination of the workplace.

The first step is to remove the top panel of the washing machine.

The second step is to take out the container for powders, this is not difficult to do. Next, you need to remove the cuff from the hatch. Caution is needed here. Use a screwdriver to pry the retaining clip, remove it, and then remove the O-ring. This should be done carefully, trying not to tear the soft rubber.

It was the turn of the control panel. In order to remove it, you need to unscrew two screws on the front of the panel and one on the right.

Next, you can proceed to dismantle the lower front panel. Pulling the latch lever, we separate the basement part of the facade - access to the drain filter and the hose for the emergency filter is open. The front panel can now be removed by unscrewing the eight fixing screws. The heating element and the drain pump open.

If during the repair process it is necessary to remove the tank and drum, then we advise you not to do this alone. Be sure to involve an assistant in this matter. Before removing the tank, you need to de-energize the heating element, disconnect all pipes, as well as the electrical wiring from the motor.

To do this, put the machine on its side, then remove the 4 screws on the bottom cover. The engine opens with a counterweight secured by shock absorbers. Disconnect the wiring from the connectors. It is important to remember what is being attached to what, therefore, before disassembling, it is advisable to photograph everything, in order to repeat everything exactly as in the picture.

But it remains to disconnect the drive belt from the engine. To do this, simply remove the belt from the pulley. Remember to put the drive belt on the small drive pulley first, then slide it over the large driven pulley and align to the center of the pulley when putting on the belt.

We present to you a diagram of the device, which will be very useful for repairs. The technical content of machines of different brands is about the same, and if you have already come across the replacement of spare parts for a washing machine, then it will be easier for you to cope with the next repair.

Now you can start a story about certain types of breakdowns and how to repair them.

The most common cause is insufficient water pressure. Then the machine stops, and in order to start it again, it must be turned off and then turned on again. If there is a lot of laundry loaded, for the machine to start, just turn it off and remove the excess.

If there is a break in the power cord or initially poor contact in the power button, then the device periodically turns off by itself. The machine may also stop if it is not level and slightly skewed.

To solve this problem, first check the water pressure in the water supply system, and also make sure that the valve supplying water to the machine is open well.

You should be aware that the free end of the drain hose connected from below must be located at a height of more than 2/3 of the height of the device, otherwise water will immediately pour out of the machine.

There are many reasons for this problem. Sometimes it is enough just to clean the powder container well - due to its clogging, water can simply flow out of it.

If, after checking these hoses, you are convinced that everything is in order with them, then the reason lies in the O-ring.

It is necessary to check the tightness of the seals, both in the door and in the connection of the filling hose. If they are worn out, they should be replaced. Then you need to check the drain pump and hose for foreign objects stuck there.

Therefore, the wash water is not heated. This is due to the failure of the heating element, but do not rush to change it - this may also be damage to the electrical wiring.

Therefore, you should carefully check the entire electrical circuit, as well as the contacts of the heating element itself, using a multimeter. If the tester shows the presence of voltage in the entire circuit, then this means that the heating element will still have to be replaced.

The place where the heater is installed should be thoroughly cleaned, only after that it will be possible to mount a new heating element.

The most common cause of noise is incorrect machine installation. Because of this, the unit produces a strong hum during spinning. For this, the position of the machine must be leveled using a spirit level.

But sometimes excessive noise can occur due to heavy wear on the bearings. It is impossible to fix them - only to change them. For an inexperienced repairman, this is a rather difficult task, because it may be necessary to saw and then glue the non-separable tank, behind which the bearing is located. Therefore, if you are not sure of your skill, then do not take up this business, it is better to call a qualified specialist.

But if the tank of your car can be disassembled, then this task can be within your power. To do this, you need to remove the tank, then disassemble it by unscrewing the bolts and disconnecting the fastening latches.

After the defective bearing has already been removed, you should thoroughly clean the shaft, check if it is worn out, and then just install a new bearing.

Finally, we present a short list of error codes that are most often issued by the unit.

E1 - system error when filling with water. Means that the required water level during filling is not reached within 20 minutes. Eliminated by turning off and then turning on the machine.

E2 - error when draining. Most often occurs when the drain filter is clogged.

E3 - too much water. You do not need to do anything, the water is automatically drained within 2 minutes.

E4 - too many things. Their mass does not correspond to the parameters of the machine. You need to extract the excess.

E5 - water heating does not work.

E6 - malfunction of the heating element.

E7 - malfunction of the water level sensor in the tank.

E8 - water heating does not match the selected wash program. Most often due to problems with the heating element.

E9 - water leakage or drain, recorded more than 4 times.

DE, DOOR - bad blocking. Most often - a badly closed hatch door.

We bring to your attention a good video that you need to watch before you start replacing the bearing yourself.

The process of dismantling and replacing bearings: