DIY washing machine repair ardo 800

In detail: do-it-yourself repair of ardo 800 washing machines from a real master for the site my.housecope.com.

Modern automatic washing machines Ardo Tl105S, Ardo 800 (400, 1000, etc.), are typical representatives of high-tech devices of this type, designed to facilitate the everyday side of our life.

But no matter how high-quality any technique would be, sooner or later, users have problems using it. That is, the machine or some of its individual functions stop working in the standard mode for this equipment. To be honest, most of the ACM breakdowns occur due to the fault of the users.

Those who operate the machine for washing clothes in violation of its operating conditions. But be that as it may, the washing machine has broken down and you need to take some action to resume the operation of the AFM. Let's say right away that the choice here is not great. And there are only three solutions. And one of them is quite exotic. So! In the event that your washing machine is an Ardo company, model Tl105S, Ardo 400, 800, 1000 or any other, is out of order, you can take the following actions:

Throw away the spoiled machine in a landfill and buy a new one.
Call a professional repair specialist for this type of equipment from the service center.
Do-it-yourself repair of the Ardo Tl105S washing machine.

Let's leave the first two options and take a closer look at the topic of repairing the Ardo 800 washing machine with our own hands, as closer in spirit to people who are confident in themselves and have the same hands (and head).

Examples of 2 different types of malfunctions when repairing an Ardo Tl105S washing machine with your own hands

Video (click to play).

According to statistics, about 80 percent of AFM breakdowns are attributed to the mechanical component of the device. And only 20, for the so-called electronic brains of the washing machine. It is for this reason that, as an example, the manuals on how to repair an Ardo washing machine with your own hands were taken - the electronic control module (ECM) of the ASM and the bearings from the drum drive shaft.

In all automatic washing machines of the latest generations, EMU is responsible for the following operations:

Soaking dirty things (linen).
Washing itself in several modes.
Rinsing.
Provides control of temperature and liquid level in the AFM.
Drainage of waste, dirty water and the like.

Thus, in the event of a breakdown of this kind, self-diagnostic testing of the AFM should be performed to identify a more specific place or part (all latest generation machines are equipped with this function) .After the test, the device will display information with an error code, that is, indicating the type and location of the breakdown.

For an Ardo module, this is the code F13 or F14. The problem of identifying a malfunction of the bearings of a washing machine is even easier to solve. This will be reported to you by a roar and similar noises emitted from the drum when it is running in the washing or spinning mode.

Before talking about the steps that should be taken to repair the module of the Ardo washing machine with our own hands, we will delimit them as far as possible. So, if ACM indicates the error code - F13 or F14, then you can:

Check and replace the control module fuse.
Completely replace the entire EMU.
Call the master or take the car to the service.

Unfortunately, there are 4 options, namely, partial repair of the module with the replacement of its individual parts, for a non-professional in radio electronics - no. We remind you that the AFM of today is a computerized device and the module is the main, main and expensive part of it.Thus, an amateur's ride to fix the EMU with his own hands will only lead to a final and complete breakdown of the washing machine, but to completely replace the damaged control module is a task quite feasible for a person with properly growing hands. And it takes place in this order:

We find and carefully study all the available information related to the replacement of the electronic module of the Ardo washing machine.
Disconnect the faulty unit from the power supply.
We release from the fasteners and remove the upper panel of the ACM Ardo, in order to provide access to the control module.
We release the printed circuit board from the fastening elements.
We disconnect the electric wires going to it.
We remove the board and replace it with a new ECU.
We return (assemble) the machine to its original technical condition.
We make testing.

Having determined the place of possible breakdown, by default these are the bearings located on the drum shaft of the washing machine, we proceed to the preparation of the repair. Note that the repair itself is completely uncomplicated, but requires a certain endurance. For the reason that in order to get to the part that needs replacement, you will have to disassemble almost the entire machine.

First of all, we purchase new bearings and oil seals that are fully suitable for the AFM of your brand and model. You can find information about this in the technical data sheet of the device. After the necessary spare parts are purchased, we prepare the tool that you need to carry out the repair:

Open-end wrenches and caps.
Phillips and straight end screwdrivers.
VD-40 grease or its analogs.
Hammer.
A metal pin (rod) of small cross-section, 30 - 40 centimeters long.
Pliers.
Silicone sealant.

We start repairing the washing machine:

We release the fasteners and remove the panels of the machine in the order described in its operating and repair instructions. The purpose of these actions is to gain access to the washing machine tank.
Having reached the tank, we remove it, having previously freed the drum from the connections and wiring.
We divide the tank into two parts, in connection with which we get access to the shaft at our disposal.
We release the screw that secures the pulley.
We knock out the shaft with a hammer (carefully).
We replace the worn out bearings located in the rear of the drum by carefully knocking them out of the bore.
We replace the bushing oil seals.
We assemble AFM units and elements in reverse order.
We connect to electricity and make a test run of the device.

Do-it-yourself Ardo washing machine repair on video

Read the recommendations for repairing the Ardo washing machine from the master!

The manufacturer (translated from Italian home appliances) is Antonio Merloni.

Front loading standard - FL models.
Drying - WD.

30% - blockage of the drain path, wear and damage to the pump:

We open the loading door, on the sticker we determine the model of the machine.

Having unscrewed the drain filter at the front at the bottom, we clean it.

We change the pump, which is located at the bottom right on the back side.

We loosen the clamp on the drain pump branch pipe.

We check the pump, clean it - in case of a malfunction, we change it.

Over time, mechanical wear appears on the shaft. The impeller dangles and does not pump out water well.

20% - malfunction of the electronic control board:

MINISEL board: Ardo models FL1000, FL1202, FLS81S, A800XEL, AE810, AE800X, SE810, FLS81S, AED1000X, TL1000EX, TL1010E ANNA610, ANNA 600X, A410, A610, A500, A1000.

We look at the power supply and the level of constant voltages (5 and 12 V) at its outputs. If there are no voltages at the output of the PS, the corresponding elements are checked - a power switch, a power filter, a power transformer T1, a rectifier (D11-D14), a U1 microcircuit.

Module DMPU: Models A800, A804, A810, A814, WD800X, S1000X, T80, T800, TL800X, TL804, etc.

Malfunctions in the DMPU module

breakage of resistances R51 (A, B);
stabilizer U3;
Zener diode D24 (short circuit);
open varistor VDR5.

relay K1, K2;
Rsimistor TR2.
Diodes D1-D6, D9-10, D15, D23.

A thing of the past module DMPA:

They are used in typewriters with an asychronous drive motor and a mechanical controller.

Models A1000PL, A1000XCZ, A1000XPL, WD1000PL, TL1000X, etc.

The wear of the heating element increases with “hard” water.

Overgrowing with scale (scab), it gives off heat poorly and burns out.

You need to pull out the gum and not the heating element. Since pulling out the heating element, you can wedge the gum.?

This is important to avoid further leakage under the seal.

10% - wear of brushes of the collector motor, loosening of contacts, breakage of the drive belt

Remove the belt, unscrew the screws and remove the engine. The motor has two brushes, each attached with two screws. We unscrew the screws and remove the brushes.

Inspect the board motor power supply terminal and ground wire.

Very often, the contacts are oxidized from moisture and the machine gives an error because of this.

Each brush is installed in a brush holder. It can be taken apart into two halves. Pay attention to how much the brush protrudes.

This size should be at least 1 cm. The best option is 1.5 cm. After that, we assemble everything and put it back in place.

10% - extraneous noise (bearings, shock absorbers, foreign object)

Having jammed the pulley, unscrew the upper shaft clamping nut counterclockwise.

If the oil seal is not filled with a specialized grease and the cross bushing is not lubricated with it during assembly, the oil seal will wear out very quickly, no matter what quality it is, this has been proven in practice.

It is not worth saving and improvising with lithol, grease and other lubricants, better get specialized lubricants that are used to lubricate oil seals.

Standard sizes of Ardo bearings and seals:

This applies to modern technology - since 2000 (models AE800X, AED1000X, TL1OOOEX).

Thanks to it, you can diagnose (control module DMPU):

Close the hatch (without linen). Set the program selection to 30 ° C until it clicks. The temperature regulator to 0 ° C. Turn on. The drum rotates at 250 rpm. To check the buttons half load, additional rinse and others, press them. The spin speed increases from 250 to the maximum, provided for this model. In the absence of additional functions, press the spin button.

Indicators will blink when a malfunction is detected.

E00 | E01

E02

E03

F6 | F9 | F12

F13 | F14

Breakdowns are rare, usually associated with improper operation. Italian technology is distinguished by its high manufacturability and versatility.

How to carry out a service test equipped with the MINI-SEL board:

Control panels look different

The steps to enter the check mode are shown in the figures.

Image - DIY repair of washing machines ardo 800

- move the program selector knob to the 6 o'clock position
- press the button 4 - ENERGY WASH and, while holding it, press the POWER button.
After that, the CM should go into test mode.

With temperature control knob:

- turn the program selector knob to the 6 o'clock position
- move the temperature selection knob to the 9 o'clock position
- press and hold the ENERGY button (for at least 6 s), at the same time turn on the power supply of the CM with the POWER button.

After that, the CM should go into test mode.

Turning the selection knob, we check the devices:

Knob in position 1 (autotest) - NTC temperature sensor (sensor circuit - for open or short circuit), pressostat, display (if any), door lock and main function buttons on the control panel

2. First, the cold water inlet valve is opened until a signal is issued from the water pressure sensor. The filling of water takes place through the compartment of the dispenser for the PREVIEW.

3. First, the heating element turns on and the water in the tank heats up to 60 ° C. Then the CM drum starts to rotate in a cyclic mode at a speed of 45 rpm (as in a washing mode).

4. The drain pump (pump) turns on. At the same time, the drum starts to rotate as during spinning.

5. Within 10 s, the hot water filling valve is turned on (if this CM model has it). At the same time, the CM drum starts to rotate.

6. The fan and heating element of drying are included (for models with drying)

The test mode is exited by turning off the power with the POWER button.

Elimination options:
1. It is necessary to check the presence of water in the water supply. It is trite, but very often the reason for the appearance of an imaginary malfunction is such funny things.

2. The inlet hose is squashed or clogged. We check visually for the absence of compression. We unscrew the hose from the washing machine, turn on the tap and see if the water will pass through? Of course, care must be taken to ensure that the water does not drain onto the floor. If the water does not come out, we find and remove the blockage. The hose with a leakage valve after the protection has been triggered will have to be replaced with a new one.

3. The filler mesh on the back of the washing machine is cleaned. The mesh is quite fine and often clogged with rust or other particles from the tap water. The filter can be easily removed with pliers and cleaned thoroughly.

4. It is necessary to make sure that the filling valve is in good working order. It is located just behind the filter. The valve becomes accessible after removing the top cover of the washing machine. Perhaps the wires of its power have come off or frayed. To check the functionality, the valve itself can be removed and connected to the voltage indicated on its body. Should open. If it does not work, you will have to change the valve to a new one.

5. The problem may be related to a faulty water level sensor. Or, in another way, the pressure switch. You can also find it under the top cover. It is removed quite easily. It is held in place by screws or latches on the body of the washing machine. We check the integrity of the wires and their connection to the sensor. A tube comes up to the pressure switch from below. It may be clogged. The simplest test for the performance of the sensor after removing it is to blow into its tube. If you hear a click, the pressure switch is most likely working properly. Otherwise, you will have to change to a new one. It is important not to mix up the wires when installing a new one.

Common causes and solutions:
1. Again, about the banal - you need to make sure that the sewer pipe is not clogged. Maybe the car just has nowhere to drain the water. Of course, this is possible with machines with a permanently connected drain. We also check the drain hose of the washing machine. It should not be kinked or twisted. In principle, you can disconnect the hose from the sewer and check if water comes out of it when draining? If it does, we clean the sewer system. If not, check the hose for clogging. Problem still exists? We look further.

2. The drain filter is clogged. Simple, but the most common reason for the lack of a drain. The filter is located at the bottom of the washing machine under the door or decorative panel. It is a screw plug screwed into the machine body using a standard right-hand thread. Accordingly, the filter is unscrewed counterclockwise. Do not forget to place a tray under the washing machine to collect the flowing water. After removal, the filter is cleaned of impurities. You will need to remove the excess in the place where the filter was installed. Next, reverse the process and check the drain. Most often it helps.

3. Blocked or faulty drain pump.A common problem for Ardo washing machines is the blocking of the pump due to foreign objects entering it. Various coins, buttons and other items left in the pockets of the washable clothes, getting inside the drain pump, prevent it from performing its functions. A symptom of a blockage of a working pump - at the moment the drain is turned on, the pump hums, tries to expel water, but cannot. Another option is that the pump has become completely unusable. In any case, he will have to be removed. In Ardo washing machines, it is very easy to access the drain pump from the bottom of the machine. They have no bottom or are covered with an easily removable plastic strip. It is enough to lay the car on one side and the access is open. Before removing, you can check the pump performance with a multimeter. Further, the clamp of the rubber pipe is loosened and it is separated from the pump. The same procedure is for the drain hose. Power wires are disconnected. It remains to unscrew the screws that hold the pump and remove it. A serviceable pump is disassembled. And foreign objects are removed from it. The defective one is replaced with a new one.

4. The lack of drainage can be caused by incorrect operation of the pressure switch. It simply may not send a signal to the control module to drain. We have already discussed what needs to be done with the water level sensor above.

2. A rare, but possible breakdown is a malfunction of the temperature sensor. It is checked by measuring the resistance at room temperature and when heated with hot water. A non-working sensor is simply replaced.

3. It is necessary to make sure that there is no "sticking" of the contact group of the heating element relay on the control module.

Any household appliances fail sooner or later. In some cases, this is physical wear and tear of parts and components of the unit, in others, incorrect connection and operation, and in others, marriage. We will devote this article to such a technique as Ardo washing machines, consider their typical breakdowns, the reasons for such breakdowns, and how to repair Ardo washing machines with our own hands.

The user understands about the breakdown of the washing machine based on specific symptoms. Only after studying these symptoms, he can assume a breakdown of a particular unit. Therefore, we will start by listing the most common symptoms.

The machine has stopped draining water. This can happen for several reasons, the main of which is the clogging of the drain system, which includes: a branch pipe, a drain hose and a pump. In very rare cases, the water does not drain due to a breakdown of the water level sensor.
The machine does not heat up the water, especially when washing 60-90 0 C. The reason for this malfunction is the breakdown of the heating element, which burns out due to limescale and settling scale. But the development of the resource of the heating element is also possible.
The drum does not rotate in the machine, it stands still. In Ardo washing machines, the tank rotates due to the drive belt, and if it breaks or falls off the pulley, the machine will stop. The problem is solved by replacing the drive belt.
Extraneous sounds appeared in the typewriter, similar to knocking or crashing. If such a knock is heard when the machine is turned off, then the reason is clearly in faulty bearings. Another reason for the rumble can be a foreign object in the tank.
Is there water leaking under the machine? The reason must be looked for in the drain filter or pipes. In the worst case, oil seals and bearings need to be replaced.
Programs get lost or the machine does not turn on at all, which means that the reason lies in a malfunction of the electronic board.

Before you panic and call the master, take a close look and listen to the "symptoms" that appear, perhaps you yourself can find the cause or even carry out repairs yourself.

In many washing machines, the manufacturer has programmed error codes into the microprocessor, which appear on the display in the event of a malfunction. Here are some examples of codes of common malfunctions. A all codes of any Ardo model can be found in the instructions.

E00 or E01 - no water drainage due to clogged drain filter.
E02 - incorrect draining during spinning, the position of the drain hose is violated.
E03 or F4 - the drain time is exceeded, the drain pump is broken.
F2 - problems with the temperature sensor, heating element or control board.
F5 - self-draining, wrong connection of hoses.
F13 or F14 - malfunction in the control module.

Having found out the cause of the malfunction, we determine - call the master or we will repair it ourselves. In some situations, it really is not worth overpaying, but doing the repair yourself. For example, blockages that have arisen can be removed. Most of the garbage accumulates in the drain filter, so cleaning it belongs to minor repairs and can cost about 600 rubles. Although in fact, there is nothing complicated about it:

Open a small door at the bottom of the front of the machine or remove the bottom panel.
Then place a large, absorbent cloth on the floor in the area of the filter.
Unscrew the valve counterclockwise.
Pull out the filter.
Rinse it well with water, remove hair and other debris.
Screw the filter back on.

The problem is debris can become clogged not only in the filter, but also in the drain hose, nozzles and the drain pump... To get to them you will have to open the car body. And this is classified as repairs of medium complexity, the price for which starts from 1200 rubles, and if a malfunction of a spare part is found during the disassembly of the machine, then you will have to buy a spare part as well.

If a foreign object gets stuck in the tank, such as a bra bone, then you will have to completely disassemble the machine. Such repairs are assessed as difficult and will cost at least 2,000 rubles. And if you are wondering how you can get an item out of a car, then you can read an article on how to remove a bra bone from a typewriter.

You can replace or clean the pump yourself if you have free time and skills in working with simple tools.

In the Ardo washing machine, you can get to the pump from the bottom side, it is either absent, or the plastic strip can be easily removed. The entire algorithm of actions and video instructions are in an article on our website on how to clean the drain pump in a washing machine.

If it is necessary to clean the drain hose, then one of its ends must be pulled out of the sewer pipe, and the other must be disconnected from the pipe coming from the pump. Then the hose itself is cleaned with a flexible cable, at the end of which there is a small brush. After that, the hose must be rinsed under running water, wiped and connected in place.

Quite often, a heating element fails in washing machines. Diagnosing its malfunction is simple: when washing things in water heated to 60 0 C, put your hand to the drum hatch. And if it is cold, it means one thing - the ten is burnt out, you will have to change it. Replacing a heating element refers to repairs of medium complexity, the cost of which will cost up to 2,000 rubles plus the cost of the heating element. But do not rush, because getting to the heating element is not difficult and you can do this through the back cover of the case, for this:

We disconnect the machine from the network, disconnect it from the water supply and sewerage system, deploy it so that it is convenient to work.
We unscrew the self-tapping screws around the perimeter of the machine that hold the cover.
We find contacts and wires coming from the heating element under the tank, remove the terminals and sensors.
We unscrew the bolt that secures the heating element.
Gently, with blabbing movements, we pull the ten on ourselves, you can pick up the ten with a screwdriver.
We clean the heating element holder from debris.
We take the original heating element for the Ardo typewriter, insert it into the holder for the heating element, so that the sealing gum completely fits into place.
We tighten the bolt, connect all the terminals.
We collect the machine.

Pay attention! Regular cleaning of the washing machine from scale will extend the life of the heating element, but you should not rely on advertised water softeners.

Replacing the electronic module is also not difficult and belongs to the middle class. However, this is in the case when there is confidence that the module will have to be completely replaced one hundred percent. But in some situations, the module can be repaired by replacing individual elements on it. This is of particular importance, because the module itself is quite expensive, in some models its price is one third of the price for the entire machine. It is not uncommon for people to refuse such repairs and buy a new automatic machine.

Working with electronics is specific, it is necessary to possess not only the skills of working with tools, but also knowledge in a certain area. Therefore, in such a situation, it is better to contact a specialist who accurately diagnoses the malfunction and can replace the element correctly.

For your information! There were times when some craftsmen independently changed the control module, connecting all terminals and sensors, and as a result, the new module burned out.

The most difficult repair, according to experts, is the replacement of bearings and oil seals in Ardo washing machines. This is because you have to almost completely disassemble the machine and take out the tank, and the bearings themselves are difficult to remove. Special tools, patience and dexterity may be required. In such a situation, it is much wiser to give the car to the craftsmen than to repair it in your apartment, where there is not much room to turn around.

For those who still want to save money or gain experience in repairing washing machines, we suggest watching a detailed video on replacing bearings.

Do you need to repair your Ardo washing machine? You have a choice: repair the equipment yourself or contact a service center. In the latter case, additional expenses are foreseen for the work of the wizard. Therefore, we will tell you how to find and fix a breakdown with your own hands.Error codes will help determine the location of the problem: E00 / E01, E02, E03, F2, F4, F5, F6 / F9 / F12, F8, F13 / F14. The control board diagnoses the system in the event of a breakdown and displays a set of symbols on the display. Each of them points to a different problem. The decoding of errors can be found in the operating instructions and our article.

Serviceability of the heating element and its wiring.

Thermal sensor performance

Remove debris from the drain filter, hose, pipe.

Replace your broken pump

Replacing the motor brushes.

Repair of windings.

Installing a new module

Ardo washing machines are divided into two main categories according to the type of load:

Vertical (Ardo TLN 85 SW, T80X, TLN 106 SA).

Frontal (Ardo SE 810, FLN 126 LW, A 1033, WDO 1485 L).

The Ardo top-loading washing machine features a compact body that easily takes up the space between the bathtub and the sink. But it is not without its drawbacks.Here's what users are complaining about:

Machines with a long service life (more than 5 years) spontaneously open the drum flaps. This leads to jamming and separation of the flaps.

The top cover of the drum is often corroded because the water is fed through the top.

Close the flaps more tightly. Clean the latch from debris, adhering powder.

Do not overload the tank with laundry.

Observe the dosage of the detergent to prevent foaming.

Wipe the drum with a dry cloth after washing to avoid corrosion.

The rest of the problems are similar to the front models. The most common ones are:

The "Ardo" washer is noisy and makes extraneous sounds.

The equipment does not drain water.

There is no water heating.

The drum does not rotate.

After switching on, there is no water intake or it flows in excess of the norm.

Let's see how to make an independent repair.Some breakdowns can be eliminated without the help of a wizard if you follow our recommendations.SMA buzzes, makes noise, vibratesHave you bought your car recently? Did the unit start jumping and rattling when you first started it? Check if the shipping bolts have been removed. They lock the tank in place to prevent damage during transport.

Unfold the case with the back wall.

Remove the bolts around the perimeter.

Also make sure the equipment is level and stable on the surface. The floor must be level and firm. Twist the legs of the clipper if necessary.The most serious failure is bearing wear. In this case, not only a rumble is heard, but also a grinding noise (with severe wear). Replacing a bearing is considered a difficult repair. How to disassemble the CM "Ardo" and install a new bearing, watch the video: