In detail: do-it-yourself repair of samsung washing machines replacement of a bearing from a real master for the site my.housecope.com.
Owners of home appliances of a well-known South Korean brand will be interested in how a Samsung washing machine is repaired with their own hands.
Unfortunately, sometimes it is necessary to eliminate breakdowns and leaks of washing machines, even in an expensive price segment, and knowledge of error codes and related malfunctions may also be required.
First, you should familiarize yourself a little with the main features of these machines. First, it is stylish design.
Secondly, it is the original design of the drum. Modern modifications of Samsung washing machines are equipped with a fundamentally new technical solution - Drum Diamond Drum .
It belongs to an innovative type of honeycomb drums with a surface covered with many convex pyramids and small water holes, into which the fabric is not drawn.
Thanks to this design, a gentle wash cycle is provided. These drums can be very spacious - with a load of up to 12 kg of laundry, depending on the model of the machine.
Thirdly, worthy of attention heaters with double ceramic coatingnot covered with limescale, and inverter motorattached directly to the drum in some modifications.
Also interesting are the functions Fuzzy Logic and Smart Check responsible for the correct calculation of the washing mode depending on the amount of loaded laundry, as well as for diagnosing various machine malfunctions.
The number of wash programs depends on the model of the washing machine. Even the simplest modifications are equipped with all the necessary set of programs, and the new models have a washing mode called ECO Bubble - with the help of air bubbles, laundry is easier to wash even in cold water.
Video (click to play).
If the machine is marked with Wf, it means that this model is front-loaded, and if its name contains the abbreviation WD, it means that the machine is equipped with a built-in dryer.
But Samsung brand machines also have one small drawback - their instability to voltage drops in the network, which is important in our Russian reality.
When the voltage becomes either too high or low, then a control system called Volt Control simply turns off the washing mode to resume it immediately after the mains voltage has stabilized. This is not always convenient, so it is better to connect the washing machine through a voltage regulator.
After a short acquaintance with the parameters of this brand, let's move on to considering the main breakdowns.
To understand the malfunction that has arisen, you need to consider the most common of them and the reasons for their occurrence.
Here is a list of common problems:
Further, the methods of repairing them with your own hands will be considered, because it is not always possible to call the master. And for this you need to have a set of necessary tools.
Before starting repairs, you need to make sure that all the tools from this list are available:
flat and Phillips screwdrivers or screwdriver;
set of wrenches;
pliers, pliers, wire cutters;
tweezers - elongated and curved;
powerful flashlight;
long-handled mirror;
soldering iron;
gas-burner;
small hammer;
knife.
In addition to the listed tools, you may need a magnet to pull out small metal objects inside the machine, a long metal ruler to align the drum, a multimeter or voltage indicator.
But that's not all. In addition to the required set of instruments, the following building materials will need to be purchased for repairs:
sealant;
Super glue;
insulating resin;
soldering materials - rosin, flux, etc .;
wires;
clamps;
current fuses;
rust remover;
electrical tape and scotch tape.
Sometimes a multimeter is not needed, it is enough to turn on the machine and select a mode with a high water temperature. From the operation of an apartment electricity meter, it is easy to understand whether the heating element is receiving power.
If you are a beginner, then you can advise using a camera to shoot a video or to photograph a workflow, so as not to confuse the sequence of actions and then assemble the machine correctly.
There are several important rules to remember that must be followed before starting repair work:
it is necessary to drain all the water from the machine;
before disassembly, be sure to (!) disconnect the device from the power supply;
choose a bright and spacious enough place for renovation.
If the unit cannot be moved to a convenient location, then ensure maximum illumination of the workplace.
The first step is to remove the top panel of the washing machine.
The second step is to take out the container for powders, this is not difficult to do. Next, you need to remove the cuff from the hatch. Caution is needed here. Use a screwdriver to pry the retaining clip, remove it, and then remove the O-ring. This should be done carefully, trying not to tear the soft rubber.
It was the turn of the control panel. In order to remove it, you need to unscrew two screws on the front of the panel and one on the right.
Next, you can proceed to dismantle the lower front panel. Pulling the latch lever, we separate the basement part of the facade - access to the drain filter and the hose for the emergency filter is open. The front panel can now be removed by unscrewing the eight fixing screws. The heating element and the drain pump open.
If during the repair process it is necessary to remove the tank and drum, then we advise you not to do this alone. Be sure to involve an assistant in this matter. Before removing the tank, you need to de-energize the heating element, disconnect all pipes, as well as the electrical wiring from the motor.
To do this, put the machine on its side, then remove the 4 screws on the bottom cover. The engine opens with a counterweight secured by shock absorbers. Disconnect the wiring from the connectors. It is important to remember what is being attached to what, therefore, before disassembling, it is advisable to photograph everything, in order to repeat everything exactly as in the picture.
But it remains to disconnect the drive belt from the engine. To do this, simply remove the belt from the pulley. Remember to put the drive belt on the small drive pulley first, then slide it over the large driven pulley and align to the center of the pulley when putting on the belt.
We present to you a diagram of the device, which will be very useful for repairs. The technical content of machines of different brands is about the same, and if you have already come across the replacement of spare parts for a washing machine, then it will be easier for you to cope with the next repair.
Now you can start a story about certain types of breakdowns and how to repair them.
The most common cause is insufficient water pressure. Then the machine stops, and in order to start it again, it must be turned off and then turned on again. If there is a lot of laundry loaded, for the machine to start, just turn it off and remove the excess.
If there is a break in the power cord or initially poor contact in the power button, then the device periodically turns off by itself. The machine may also stop if it is not level and slightly skewed.
To solve this problem, first check the water pressure in the water supply system, and also make sure that the valve supplying water to the machine is open well.
You should be aware that the free end of the drain hose connected from below must be located at a height of more than 2/3 of the height of the device, otherwise water will immediately pour out of the machine.
There are many reasons for this problem. Sometimes it is enough just to clean the powder container well - due to its clogging, water can simply flow out of it.
If, after checking these hoses, you are convinced that everything is in order with them, then the reason lies in the O-ring.
It is necessary to check the tightness of the seals, both in the door and in the connection of the filling hose. If they are worn out, they should be replaced. Then you need to check the drain pump and hose for foreign objects stuck there.
Therefore, the wash water is not heated. This is due to the failure of the heating element, but do not rush to change it - this may also be damage to the electrical wiring.
Therefore, you should carefully check the entire electrical circuit, as well as the contacts of the heating element itself, using a multimeter. If the tester shows the presence of voltage in the entire circuit, then this means that the heating element will still have to be replaced.
The place where the heater is installed should be thoroughly cleaned, only after that it will be possible to mount a new heating element.
The most common cause of noise is incorrect machine installation. Because of this, the unit produces a strong hum during spinning. For this, the position of the machine must be leveled using a spirit level.
But sometimes excessive noise can occur due to heavy wear on the bearings. It is impossible to fix them - only to change them. For an inexperienced repairman, this is a rather difficult task, because it may be necessary to saw and then glue the non-separable tank, behind which the bearing is located. Therefore, if you are not sure of your skill, then do not take up this business, it is better to call a qualified specialist.
But if the tank of your car can be disassembled, then this task can be within your power. To do this, you need to remove the tank, then disassemble it by unscrewing the bolts and disconnecting the fastening latches.
After the defective bearing has already been removed, you should thoroughly clean the shaft, check if it is worn out, and then just install a new bearing.
Finally, we present a short list of error codes that are most often issued by the unit.
E1 - system error when filling with water. Means that the required water level during filling is not reached within 20 minutes. Eliminated by turning off and then turning on the machine.
E2 - error when draining. Most often occurs when the drain filter is clogged.
E3 - too much water. You do not need to do anything, the water is automatically drained within 2 minutes.
E4 - too many things. Their mass does not correspond to the parameters of the machine. You need to extract the excess.
E5 - water heating does not work.
E6 - malfunction of the heating element.
E7 - malfunction of the water level sensor in the tank.
E8 - water heating does not match the selected wash program. Most often due to problems with the heating element.
E9 - water leakage or drain, recorded more than 4 times.
DE, DOOR - bad blocking. Most often - a badly closed hatch door.
We bring to your attention a good video that you need to watch before you start replacing the bearing yourself.
The process of dismantling and replacing bearings:
What the disassembly process looks like:
Before starting an independent repair, you always need to correctly assess your own strength and not take on overwhelming work. But repairing a washing machine yourself is not very difficult, it is enough to understand a little about mechanics, electrical engineering, and also have the necessary tools and materials at hand. You will succeed!
Hello everyone.Let me introduce you to a short instruction in which I will tell you how to replace faulty bearings in a washing machine drum. Very often there are questions from owners of washing machines on the topic of noise during operation and replacement of bearings. The noise during washing is primarily emitted by the drum bearing. I have washing machine samsungR1043... She worked for 6 years during which there were no complaints about her.
There were a lot of laundry during this period, I think about one and a half washes a day.
After 6 years, I thought about changing the washing machine to a new model. Chose a car Lg with a direct motor. And like a custom-made machine Samsung started making noise when washing. I purchased the selected model, which by the way is very quiet.
Since the call of the master and the consumables would cost me a normal amount, I decided to repair the machine myself. If you do it carefully, then everything will certainly work out. The main thing is to keep your arms straight. Next, I suggest you something like instructions for disassembling the washing machine and replacing the drum bearings. The article is voluminous due to the large number of photos, but it will be easier to understand the process of disassembling and replacing bearings.
First, let's decide on the necessary tool. Since I started not knowing that I would need a tool, I was looking for a repair. Here is a list of the entire set for you.
Since it is necessary to get to the drum of the machine to replace the bearings, it is necessary to disassemble it completely. Some models have a special cover on the back of the case, which provides access to the motor, belt indiscriminately. However, my model had to be completely disassembled. To do this, you need enough space so that it is more convenient to work and expand the parts.
Let's start disassembling. You must first remove the top cover, which is attached with two self-tapping screws from the back. To remove the cover, you must move it away from the face of the machine and lift it.
Remove the washing powder tray. The container is removed and three hoses are disconnected from it, they are clamped with metal clamps. It is convenient to open these clamps with pliers.
After removing the cover, it immediately catches your eyes large counterweight... The names of the parts are mine, since I do not know what they are actually called, but I think everything will be clear to you. Remove the large counterweight, which is attached with two long bolts.
We unscrew the bolts and remove the counterweight by lifting it up.
The counterweight is not light, so don't drop it or split it. By the way, it looks like a cast piece of cement mortar.
The body of the machine is connected to the drum by a rubber casing, which is attached to the drum by a large steel wire clamp. It is loosened by loosening the bolt.
Drum body without counterweight (top view).
Next, we put the car on its side and remove the bottom cover. It is made of plastic and is held by 4 self-tapping screws. Unscrew and remove.
A small counterweight, an electric motor and a pump are hidden behind the bottom cover, which are attached to the drum body. This whole structure rests on the body of the machine with two shock absorbers.
Next, we need to disconnect all cables from the contacts of the electric motor and pump.
Disconnect the two shock absorbers from the washer body, which are bolted down.
From the side of the top cover is connected to the body water inlet, unscrew it without disconnecting the wires. (wires will not interfere with us).
From above, the drum body is supported by spring hangers. Using pliers, first disconnect the hooks from the drum body, and then from the machine body. We'll have to suffer a little, but everything will work out for sure!
In order to take out the drum, it is necessary to remove the front part of the washing machine. First, unscrew the control panel and then remove the front part with the door. All of them are fastened with self-tapping screws. The screwdriver did it in half a minute.
And here we have a disassembled car body.We unscrew the small counterweight to make it easier to remove the drum body.
Here is such a small counterweight.
Those same spring hangers.
Now we carefully take out the drum body and place it on the floor. Before us is the main part of the washing machine.
At the back, remove the belt that connects the drum wheel and the electric motor.
An 8-point hexagon bolt attaches the wheel to the body. We unscrew it and remove the wheel.
We begin to disassemble the drum body.
We unscrew the shock absorbers first, unscrew the bolts not to the end, but only to free the second half of the body. Shock absorbers are not only attached to the drum body, but also pull together.
The body consists of two parts, which are compressed by brackets and clamps. It is easy to remove the clamps with a wrench.
You can easily remove the staples with a flat screwdriver.
Let me remind you once again to make marks in order to properly assemble the case.
We open the case and observe what is inside.
After I opened the drum, I saw an unpleasant picture. the heating element was completely covered with limescale. The plastic body itself and the drum were covered with scale.
The heating element is not easy to remove. The nut is unscrewed from the outside and it is squeezed out. You must first descale it. The element is fixed with an elastic band that expands after tightening the nut.
Now we detach the drum from the second half of the body.
Removal of the drum showed that the oil seal was unusable. The oil seal should protect the bearing from moisture, but it got to them, and they began to make noise during operation.
All scale from the body was removed with an ordinary metal brush for washing dishes. She does not scratch and does her job well. The scale turned out to be two full handfuls.
The outer bearing was ok, however I decided to replace all bearings. I knocked out the outer one (it's small) from the inside with a thick screwdriver and a hammer, gently tapping on the bearing rings. You have to be careful here, since the bearing is located in the aluminum sleeve so as not to scratch it. The inner bearing (large) was knocked out from the outside to the inside with a metal tube of a similar diameter.
He hammered the new bearings neatly into place with a hammer, placing a wooden block.
The washing machine is assembled in reverse order.
What did we end up with? The washing machine works normally, washes and does not make noise. In terms of costs, I saved a lot.
As a result, all the repairs cost me only 350 rubles.
After working for 6 years, the machine is in excellent condition, not counting the scale. I am pleased with the Samsung, but I bought LG, which proved to be very good, quiet and many modes of operation.
By the way, in order for the machine to serve you longer, you need to set it by level and check its position from time to time. Over time, due to vibrations, the washer can move out of place.
In the comments, a question was raised about an error that signals a blockage in the drain pump. Here is an interesting video that shows you how to remove the pump from a Samsung washing machine, clean it and check the quality of work.
