DIY siemens washing machine repair

Repair of washing machines Siemens (Siemens) do it yourself quite feasible, although this is a rather difficult task. If you want to make repairs less costly, it is quite possible, with the help of your hands and head, to replace the collector motor, before doing partial dismantling of the washing machine.

Malfunctions of the collector motor of Siemens washing machines can determine by following the diagnostic algorithm.

Malfunctions can occur with every mechanism of Siemens washing machines (as well as any others). But they are not all the same in terms of recoverability and financial costs.

If a collector motor breaks down in a typewriter, this is considered one of the most expensive repairs. It is believed that replacing the engine yourself is an unrealistic undertaking. And yet it is possible to do it yourself, Siemens machines can be repair at home, although for this you need to know the design features and have a little bit of experience in repair work. Malfunctions in the functioning of the motor will make themselves known by the fact that when the wash is started, the drum will not rotate.

It must be borne in mind that the lack of rotation of the drum can be associated not only with engine failures. Therefore, before taking on its replacement, you need to make sure it is his "fault".

Siemens machines are diagnosed on their own by starting the wash program and listening to how the unit works. An inoperative engine will not make any sounds if the clipper is turned on. This means that there is a need for repairs.

Replacing the collector motor belong to the most difficult types of repairs associated with Siemens washing machines. However, you can do it yourself.

First you need to dismantle the body of the washing unit. Access to the engine is possible only if two panels are removed - the upper one and the service one. The top panel is removed using a Phillips screwdriver. It is held in place by screws at the top of the rear wall.

Using the same Phillips screwdriver, dismantle the service panel, which is attached with two screws to the side walls. You must have at your disposal a small wooden or plastic crowbar: they pry the service panel with it and remove it from the case.

As a result of these manipulations, access to the internal parts is opened. Before removing the actual engine, first remove the drive belt. Then the two screws are unscrewed in the same way as in the image. Disconnecting the connectors and disconnecting the contacts, the faulty motor is removed. The new engine is installed in its place, observing the reverse assembly order.

First, they reconnect the connectors, then put a new one in place of the old motor, attach it with the same screws. Completing the repair is the return of the drive belt and the installation of the top and service panels. If everything is done correctly and no force majeure circumstances arise, we can assume that the replacement of the collector motor has been successfully completed.

Repairs to your Siemens washing machine must be carried out under conditions safety precautions! The actions provided for by the repair algorithm must be done very carefully, otherwise you can break something else. Many are tempted to make engine repairs more convenient by placing the washing machine on its side, but you can't do this.

Siemens self-repairs should be carried out in a spacious room that allows access to the washing machine from all sides without any problems. Home craftsmen often start repairs without the necessary tools, therefore, dismantling the structure, they face difficulties or even lose the opportunity to make repairs with their own hands.

The possibility of self-repairing the washing machine is always considered first. Indeed, with a certain trip, the home craftsman has the prerequisites for independently restoring the functioning of household appliances for washing. The main technical recommendations regarding repair will be described below.

Repair of Siemens washing machines can also be entrusted to specialists. As a rule, repair operations are carried out directly at the home of the owner of household appliances. However, it is important to understand that the technician may need to take the equipment to the workshop for repair, if restoration at home is impossible for some reason.

It is hardly worth describing in this article how to change the filter yourself. There is absolutely nothing complicated in this procedure. In addition, it is described in the user manual for the washing machine.

The most common technical failures include:

• aging of the hatch cuff;
• failure of the heating element;
• breakdown of the drain pump.

Replacing the sunroof collar is the easiest part of recovery. The fact is that due to incorrect use, moisture remains in the cuff. Naturally, over time, a fungus develops on moisture.

This is the main reason for the disgusting smell from the washing machine. To replace the cuff yourself, first purchase it! Finding the right one is not easy. Especially if your washing machine is imported.

The change is carried out after removing the O-ring. This can be done with bare hands (after prying the O-ring). However, there is often another O-ring. To gain access to it, you will need to dismantle the facade of the washing machine.

It is important to understand that it is impossible to restore an inoperative heating element or drain pump. Even professionals do not do this - they immediately install new components.

Dismantling the front of the washing machine is only possible after removing the powder receptacle. It is important to remember that wires fit to the facade (door blocking during washing).

The wires are connected using connectors. Consequently, replacing the heating element and pump with new analogues does not require specialized equipment.

The video clearly demonstrates the implementation of the above actions:

Household appliances from Siemens have gained popularity. But even high quality and reliable AGRs sometimes fail. It is believed that they are able to serve reliably for about ten years. However, like other devices, washing machines have their weak points, which can manifest themselves in the most inappropriate situations. Having information about typical failures, you can identify them on your own and repair Siemens washing machines on your own.

German technology is actually considered to be of high quality in all its components. Experts assure that if we compare with other washing machines, then in Siemens, in terms of reliability, we can single out the engine, control module and bearings. The listed elements rarely fail.

But the following failures are distinguished as weak places:

• the wash has ended, but the water has not left, the program has not switched to rinsing or spinning. In this case, a likely failure will be a failure or clogging of the pump;
• the machine draws in water and immediately drains it. The problem may be with the filling valve. One sign of a problem is a water leak near the detergent drawer;
• water flow.As a rule, this happens near the door or under the body. The reason is the wear of the cuffs or their weakening;
• no water heating. In most cases, the problem is related to the heating element;
• during the operation of the machine, vibration is observed, a knock is heard. In such situations, it is advisable to check the shock absorbers and dampers for wear.

Let's try to figure out how to deal with the most common failures with our own hands.

Probably, such works are the most difficult. The problem is that in a washer of German origin, you can only get to the pump if you remove the front panel. And in this case, the machine will have to be disassembled almost all.

So you should clear the place, prepare various screwdrivers and pliers, and you can start repairing:

• remove the fastening clamp from the cuff, dismantle the cuff itself;
• take out the detergent tray, turn out the self-tapping screw that secures the front panel;
• remove the bottom part of the case, under which two more screws should be unscrewed;
• unscrew the hardware fixing the pump;
• carefully move the control panel to the side to preserve the integrity of the wiring;
• we disconnect the wiring connected to the door of the machine;
• remove the front panel of the SMA.

Now you can carefully examine all the parts inside the machine. As a rule, it is recommended to start with the nozzles routed from the tank. During the inspection, their integrity and tightness are checked. To remove a broken pump, you must:

• disconnect all electrical wiring, disconnect the branch pipe leading from the pump to the tank;
• remove the water drain hose.

The pump is checked for blockages and performance. If it is in good working order, it is necessary to flush the pipes and the snail, and in the reverse order to carry out the assembly. In the event of a complete malfunction of the pump, it is changed to a similar element.

1. Intake valve replacement procedure.

It can fail for many reasons, including normal wear and tear and poor quality water. But it will still have to be changed, since most often repair work is not advisable.

How to proceed in such cases:

• the washing machine must be disconnected from the water supply and electrical energy;
• after that, the hose for water intake is unscrewed;
• use a Phillips screwdriver to unscrew the fasteners of the top panel;
• at the point of approach of the hose, we find the inlet valve, disconnect the wiring from it;
• the branch pipe is disconnected, the fasteners are unscrewed, the valve is removed;
• a new element is inserted in its place, and all actions are performed in reverse order.

Some models have a feature in the form of a plastic plug. It can be easily removed with a flat screwdriver.

1. Replacing the rubber cuff on the hatch.

This work can be done without dismantling the tank. All activities require skill and patience. You just have to purchase a similar cuff, otherwise the tightness will be broken.

• a metal clamp is removed that holds the cuff on the wall of the washer;
• we remove the wall according to the already known scheme;
• the branch pipe coming from the receiver for detergents must be disconnected;
• the position of the rubber cuff must be marked with a marker, then it can be removed, put on a new one in the vacant space;
• connect the hose;
• put the front panel in place, put on the cuff, fix it with a clamp.

1. The sequence of actions when replacing the heating element.

Increased water hardness and excessive use of the CMA lead to failure of the water heating element. The washing process will take place in cold water, and this will significantly reduce the efficiency. There are models in which, after the heating element fails, the washing process does not start at all, and the corresponding error code is displayed on the screen.

In the models of the German company, the heating element is located under the tank, behind the front panel of the machine.Having unscrewed all the screws, you can easily remove this wall, check the heating element for its performance using a multimeter. In case of malfunction, replace. To do this, you will have to:

• unscrew the nut located in the center of the base of the heater;
• remove all wires, disconnect the thermal sensor;
• pull the heating element towards you with smooth swaying;
• take a new analogue, install it in the vacated socket, after removing debris and scale from there;
• connect the wires to the corresponding terminals, tighten the nut.

1. Worn brushes, engine failure.

Motor problems account for almost a tenth of all failures. During a short circuit, the motor winding could burn out, or simply the collector brushes were worn out.

• remove the top and back panels;
• remove the drive belt from the motor pulley;
• disconnect all wires;
• unscrew all fasteners;
• remove the motor, slide the plate with the terminals and remove the brushes.

They need to be examined. In case of severe wear, it is recommended to replace it with new ones, after which the engine is installed in its original place.

There are known cases when electronic elements fail - a board or its components. The procedure is quite complicated, and a beginner may not be able to cope with it. You will need to have a wiring diagram of the unit on hand. Experienced craftsmen advise that if the board refuses to contact the workshop - repairs on your own may entail additional problems.