DIY repair samsung s832

In detail: do-it-yourself repair of samsung s832 from a real wizard for the site my.housecope.com.

Owners of home appliances of a well-known South Korean brand will be interested in how a Samsung washing machine is repaired with their own hands.

Unfortunately, sometimes it is necessary to eliminate breakdowns and leaks of washing machines, even in an expensive price segment, and knowledge of error codes and related malfunctions may also be required.

First, you should familiarize yourself a little with the main features of these machines. First, it is stylish design.

Secondly, it is the original design of the drum. Modern modifications of Samsung washing machines are equipped with a fundamentally new technical solution - Drum Diamond Drum .

It belongs to an innovative type of honeycomb drums with a surface covered with many convex pyramids and small water holes, into which the fabric is not drawn.

Thanks to this design, a gentle wash cycle is provided. These drums can be very spacious - with a load of up to 12 kg of laundry, depending on the model of the machine.

Thirdly, worthy of attention heaters with double ceramic coatingnot covered with limescale, and inverter motorattached directly to the drum in some modifications.

Also interesting are the functions Fuzzy Logic and Smart Check responsible for the correct calculation of the washing mode depending on the amount of loaded laundry, as well as for diagnosing various machine malfunctions.

The number of wash programs depends on the model of the washing machine. Even the simplest modifications are equipped with all the necessary set of programs, and the new models have a washing mode called ECO Bubble - with the help of air bubbles, laundry is easier to wash even in cold water.

Video (click to play).

If the machine is marked with Wf, it means that this model is front-loaded, and if its name contains the abbreviation WD, it means that the machine is equipped with a built-in dryer.

But Samsung brand machines also have one small drawback - their instability to voltage drops in the network, which is important in our Russian reality.

When the voltage becomes either too high or low, then a control system called Volt Control simply turns off the washing mode to resume it immediately after the mains voltage has stabilized. This is not always convenient, so it is better to connect the washing machine through a voltage regulator.

After a short acquaintance with the parameters of this brand, let's move on to considering the main breakdowns.

To understand the malfunction that has arisen, you need to consider the most common of them and the reasons for their occurrence.

Here is a list of common problems:

Further, the methods of repairing them with your own hands will be considered, because it is not always possible to call the master. And for this you need to have a set of necessary tools.

Before starting repairs, you need to make sure that all the tools from this list are available:

flat and Phillips screwdrivers or screwdriver;
set of wrenches;
pliers, pliers, wire cutters;
tweezers - elongated and curved;
powerful flashlight;
long-handled mirror;
soldering iron;
gas-burner;
small hammer;
knife.

In addition to the tools listed, you may need a magnet to pull out small metal objects inside the machine, a long metal ruler to align the drum, a multimeter or voltage indicator.

But that's not all. In addition to the required set of instruments, the following building materials will need to be purchased for repairs:

sealant;
Super glue;
insulating resin;
soldering materials - rosin, flux, etc.etc .;
wires;
clamps;
current fuses;
rust remover;
electrical tape and scotch tape.

Sometimes a multimeter is not needed, it is enough to turn on the machine and select a mode with a high water temperature. From the operation of an apartment electricity meter, it is easy to understand whether the heating element is receiving power.

If you are a beginner, then you can advise using a camera to shoot a video or to photograph a workflow, so as not to confuse the sequence of actions and then assemble the machine correctly.

There are several important rules to remember that must be followed before starting repair work:

it is necessary to drain all the water from the machine;
before disassembly, be sure to (!) disconnect the device from the power supply;
choose a bright and spacious enough place for renovation.

If the unit cannot be moved to a convenient location, then ensure maximum illumination of the workplace.

The first step is to remove the top panel of the washing machine.

The second step is to take out the container for powders, this is not difficult to do. Next, you need to remove the cuff from the hatch. Caution is needed here. Use a screwdriver to pry the retaining clip, remove it, and then remove the O-ring. This should be done carefully, trying not to tear the soft rubber.

It was the turn of the control panel. In order to remove it, you need to unscrew two screws on the front of the panel and one on the right.

Next, you can proceed to dismantle the lower front panel. Pulling the latch lever, we separate the basement part of the facade - access to the drain filter and the hose for the emergency filter is open. The front panel can now be removed by unscrewing the eight fixing screws. The heating element and the drain pump open.

If during the repair process it is necessary to remove the tank and drum, then we advise you not to do this alone. Be sure to involve an assistant in this matter. Before removing the tank, you need to de-energize the heating element, disconnect all pipes, as well as the electrical wiring from the motor.

To do this, put the machine on its side, then remove the 4 screws on the bottom cover. The engine opens with a counterweight secured by shock absorbers. Disconnect the wiring from the connectors. It is important to remember what is being attached to what, therefore, before disassembling, it is advisable to photograph everything, in order to repeat everything exactly as in the picture.

But it remains to disconnect the drive belt from the engine. To do this, simply remove the belt from the pulley. Remember to put the drive belt on the small drive pulley first, then slide it over the large driven pulley and align to the center of the pulley when putting on the belt.

We present to you a diagram of the device, which will be very useful for repairs. The technical content of machines of different brands is about the same, and if you have already come across the replacement of spare parts for a washing machine, then it will be easier for you to cope with the next repair.

Now you can start a story about certain types of breakdowns and how to repair them.

The most common cause is insufficient water pressure. Then the machine stops, and in order to start it again, it must be turned off and then turned on again. If there is a lot of laundry loaded, for the machine to start, just turn it off and remove the excess.

If there is a break in the power cord or initially poor contact in the power button, then the device periodically turns off by itself. The machine may also stop if it is not level and slightly skewed.

To solve this problem, first check the water pressure in the water supply system, and also make sure that the valve supplying water to the machine is open well.

You should be aware that the free end of the drain hose connected from below must be located at a height of more than 2/3 of the height of the device, otherwise water will immediately pour out of the machine.

There are many reasons for this problem.Sometimes it is enough just to clean the powder container well - due to its clogging, water can simply flow out of it.

If, after checking these hoses, you are convinced that everything is in order with them, then the reason lies in the O-ring.

It is necessary to check the tightness of the seals, both in the door and in the connection of the filling hose. If they are worn out, they should be replaced. Then you need to check the drain pump and hose for foreign objects stuck there.

Therefore, the wash water is not heated. This is due to the failure of the heating element, but do not rush to change it - this may also be damage to the electrical wiring.

Therefore, you should carefully check the entire electrical circuit, as well as the contacts of the heating element itself, using a multimeter. If the tester shows the presence of voltage in the entire circuit, then this means that the heating element will still have to be replaced.

The place where the heater is installed should be thoroughly cleaned, only after that it will be possible to mount a new heating element.

The most common cause of noise is incorrect installation of the machine. Because of this, the unit produces a strong hum during spinning. For this, the position of the machine must be leveled using a spirit level.

But sometimes excessive noise can occur due to heavy wear on the bearings. It is impossible to fix them - only to change them. For an inexperienced repairman, this is a rather difficult task, because it may be necessary to saw and then glue the non-separable tank, behind which the bearing is located. Therefore, if you are not sure of your skill, then do not take up this business, it is better to call a qualified specialist.

But if the tank of your car can be disassembled, then this task can be within your power. To do this, you need to remove the tank, then disassemble it by unscrewing the bolts and disconnecting the fastening latches.

After the defective bearing has already been removed, you should thoroughly clean the shaft, check if it is worn out, and then just install a new bearing.

Finally, we present a short list of error codes that are most often issued by the unit.

E1 - system error when filling with water. Means that the required water level during filling is not reached within 20 minutes. Eliminated by turning off and then turning on the machine.

E2 - error when draining. Most often occurs when the drain filter is clogged.

E3 - too much water. You do not need to do anything, the water is automatically drained within 2 minutes.

E4 - too many things. Their mass does not correspond to the parameters of the machine. You need to extract the excess.

E5 - water heating does not work.

E6 - malfunction of the heating element.

E7 - malfunction of the water level sensor in the tank.

E8 - water heating does not match the selected wash program. Most often due to problems with the heating element.

E9 - water leakage or drain, recorded more than 4 times.

DE, DOOR - bad blocking. Most often - a badly closed hatch door.

We bring to your attention a good video that you need to watch before you start replacing the bearing yourself.

The process of dismantling and replacing bearings:

What the disassembly process looks like:

Before starting an independent repair, you always need to correctly assess your own strength and not take on overwhelming work. But repairing a washing machine yourself is not very difficult, it is enough to understand a little about mechanics, electrical engineering, and also have the necessary tools and materials at hand. You will succeed!

Regardless of the level of complexity of the breakdown, you should not be afraid of repairing a Samsung washing machine with your own hands.

Nowadays, you can find a lot of information presented in such an accessible form that even a beginner can figure it out.

After reading the instructional articles and watching the video, where everything is clearly shown, it will be quite possible to do it yourself repairing typical Samsung washing machine malfunctions.

Experienced craftsmen claim that most of the breakdowns that occur are typical for all washing machines.

This is due to the similarity of their design and operating conditions.

It is another matter if it is necessary to repair a breakdown resulting from a poor-quality assembly, a factory defect, or in case of violations of program control.

In this case, it will be more difficult to fix the problem with your own hands, and it is better to seek help from service workshops.

The use of a washing machine can significantly save the energy and time of modern people.

If the device suddenly stops working, the person's life becomes uncomfortable.

Incorrect operation of the washing machine, including the Samsung brand, can manifest itself as follows:

To ensure the repair of a Samsung machine, it is necessary to make the mechanism of the device accessible, that is, to disassemble it first.

To do this, it is worth preparing the following tools:

Phillips screwdriver or screwdriver;
flat screwdriver;
pliers;
hammer;
8 spanner and hex wrench;
nippers.

First, remove the top panel. Using a Phillips screwdriver, unscrew the screws located under the top panel on the back of the Samsung machine.

Then we slightly raise the back of the panel, and with the other hand we help to move the panel towards us.

The next step is to remove the detergent drawer located on the front panel.To do this, pull out the tray and use a Phillips screwdriver to unscrew the screws on the sides. Disconnect the tray.Now it will be easier to remove the Samsung control panel.It is convenient to do this in this way: with one hand we hold the control panel on the right side, with the other hand, carefully and gradually move the left side of the panel towards ourselves, unhooking it from the mounting fasteners.Wires run from the control panel to the inside of the mechanism, it is important not to damage them.Therefore, the control panel is suspended from the right side of the Samsung washing machine using a special service device.To get a better idea of the process, we recommend watching the video tutorial.Next, you need to pull out the service panel, it is located at the bottom under the hatch door.The screws that secure the panel are located on the sides of the Samsung washing machine. They are unscrewed from the panel using a Phillips screwdriver.It will take a little effort to separate the Samsung service panel from the case, so a plastic or wooden crowbar will come in handy.

Now, having opened the window door, we remove the clamp and the cuff of the central panel. Then use a Phillips screwdriver to unscrew the screws that secure the central panel.

dismantle the central panel. Carried out together with a hatch;
disconnect the connector blocking the door;
using pliers, weaken the hose clamp, then remove the hose and clamp;
remove the hatch cuff using a Phillips screwdriver;
remove the collar cuff with a flat screwdriver;
remove the cuffs from the drum.

To assemble the washing machine, use the same steps in the same sequence, only in reverse order.

The need to replace the heating element is one of the most common breakdowns. The main reason is the hardness of the water, as a result of which an increased amount of scale is formed.

It is not difficult to carry out such repairs with your own hands as replacing the heating element. To do this, we disconnect the washing machine from all communications - electricity and sewage.

We check if there is water left in the mechanism. If so, we drain it through the drain filter. We provide access to the heating element.

In Samsung devices, it is located under the front cover.

Remove the front panel cover.

We determine the exact location of the heating device. As a rule, the heating element is located under the tank, at the bottom of the mechanism. Carefully disconnect all the wires leading to the heating element.

At the same time, we mark them with a marker so that later we do not get confused when connecting back. We loosen the fasteners of the heating device.

We carefully dismantle the heating element, trying not to touch the other elements of the mechanism. The place where the heating element was located is cleaned of scale residues. We are installing a new heating device.

The design features of Samsung washing equipment allow you to repair it not only without unnecessary hassle, but also with your own hands.Before starting the repair, it is necessary to free the machine from all communications - disconnect it from the power supply and sewerage system, disconnect the pump motor wires.Then you need to remove the fasteners of the assembly and remove the pump from the machine.A visual assessment of the condition of the pump is carried out after cleaning it and makes it possible to determine the need for its repair or replacement.If you still need a replacement, then the procedure should be as follows:

unscrew the screws on the back panel and remove the top cover;

take out the powder dispenser;

open the filter cover located in the bottom panel;

unscrewing the screws, remove the bottom panel by moving to the right;

unscrew the 4 screws located under the panel;

open the hatch, loosen the clamp, remove the cuff;

unscrew 3 bolts under the top panel, remove the front wall;

unscrew the 3 connecting bolts from the pump volute and the housing;

disconnect the pump from the electrical circuit;

unscrew the pump from the filter;

we install a new pump.

The assembly of the machine is done upside-down. For the convenience of repairs, the machine can be put on its left side.

Samsung manufactures appliances of various profiles, including washing machines. Usually diversified companies produce very mediocre products, but not in the case of Samsung. The products of this company are always of high quality and washing machines are no exception. Nevertheless, any technique breaks down, and sooner or later the consumer will have to solve this problem. As part of the article, we will consider typical breakdowns of Samsung washing machines, and also talk about how to fix them with our own hands.

An automatic washing machine, by whom and from whatever it was made, inevitably breaks down, be it a great German brand or a cheap Italian technique of Chinese assembly. Any washing machine from the Samsung company also has weak points and you need to pay attention to them first of all. Based on the statistical data provided by the leading service centers of the world, we concluded that in most models of Samsung washing machines it breaks down most often:

drive belt;
a heating element;
filling valve;
drain pump;
drain pipe.

The strengths of Korean technology are electronics, it fails 3 times less often than the above units, electric motors - they break down on typewriters 2 times less often. I would like to pay special attention to the electrician.

When you open the case of a Samsung washing machine with your own hands, the internal order attracts attention. All wires are bundled and tightened with clamps. The wires themselves are quite thick, and the terminals are made of high-quality metal, in general, high-quality equipment manifests itself even in trifles. Nevertheless, in some places the not very successful design of individual parts leads to breakdowns of the above units, which should be discussed in more detail.

Important! Most often, people turn to service centers with broken heating elements 54%, in second place are drive belts 21%, in third place filler valves 12%, the rest of the percentage is divided among themselves by other modules of the machine.

To check, repair or change the drive belt, you need to remove the back wall of the washing machine. The drive belt is considered a relatively affordable element of the Samsung washing machine, you can easily get to it, which is what you need to use. First, remove the belt from the pulley. What should be done:

we grab the belt with our hand somewhere in the middle between the pulley and the engine;
with some effort we pull the belt towards ourselves;
take a Phillips screwdriver, insert it with one hand into the groove of the pulley, remembering to pull the belt with the other hand;
We push the screwdriver along the groove until the belt comes off the pulley.

After the belt has been removed, it must be examined very carefully. We will be interested in all damage, and even hints of damage. The belt should not have strong abrasions, cracks, torn fragments, etc. If any signs of damage are found, the belt must be replaced immediately, repair in this case is impossible. You need to change the belt strictly to the original one - you do not need to look for any such spare parts, do not risk your home assistant.

Note! Take a close look at the bottom of the washing machine. If there are rubber chips on it, this indicates wear on the drive belt.

Installing a new drive belt is a bit like installing a loose chain on a bicycle. We put the belt on the engine pulley. Then you need to attach the belt with the inner part to the groove of the drum pulley with one hand, and rotate the pulley with the other - the belt will easily put on.

Problems with the drain pump and the nozzle of the Samsung washing machine come down to cleaning them. In the vast majority of cases (80%), the drain pump loses its performance precisely because of a blockage., therefore, experts advise, after dismantling this element and the branch pipe, proceed to general cleaning. To clean the pipe and pump of the Samsung machine, you need to get to them.

To some, it seems that for this you will have to disassemble half of the Samsung washing machine, but in fact, everything is much simpler. The manufacturer has taken care of the availability of the main units of its equipment, therefore, in order to get to the drain pump and the pipe you need:

remove the powder tray from the machine;
gently lower it onto the left or right wall;
unscrew the bottom protection.

After that, you will have a drain pump and a pipe in all its glory. Moreover, it is much more convenient to work with these modules through the bottom than through the front or back wall. Follow the steps below to clean the drain pump and tube.

Take a large, absorbent cloth and place it under the drain pump.
We unscrew the clamps holding the edges of the branch pipe.
Disconnect the plugs from the drain pump sensor.
Disconnect the drain hose, remembering to loosen the clamp.
We unscrew the fasteners of the drain pump and carefully remove it. Keep in mind that water will flow from it.
We remove the pipe and rinse it with a stream of hot water, we do the same with the drain pump.
We install the elements of the washing machine in place, fasten the bottom, put the machine on its legs, connect and check the functionality.

If the drain pump is faulty and the cleaning fails, the repair can be quite difficult. Experts advise not to try to disassemble and repair this unit, so as not to break it. Better give the drain pump to specialists, they may be able to carry out repairs. If there are signs of damage to the washing machine pipe Samsung, it needs to be replaced with a new one immediately.

Note! Usually, the branch pipe is frayed at the points of contact with the metal clamp, so check it carefully in these places.

Inlet valves do not break down very often on Samsung washing machines, however, it does happen and you need to know how to proceed. We note right away that repairing such a valve with your own hands can often be done quite easily, after which the reanimated module will work for a long time and without problems. What is the most common inlet valve breakdown? Of course, the rubber bands. Over time, they coarse, dry and crack, losing their ability to hold water, this leads to self-filling of water into the tank.

To repair the filler valve with your own hands, you need.

Remove the top cover of the washing machine; to do this, unscrew the two bolts located on the rear projection of the top cover.
Pull the cover towards you a little, and then up and it can be easily removed.
Now you need to find the filler valve, for this, pay attention to the place where the filler hose fits, in the body it connects to a small barrel-shaped element - this is the filler valve.
We loosen the clamps and unscrew the filler valve, not forgetting to disconnect the sensor wire.
We check the condition of the valve sealing rubber bands and replace them with new ones.
We check the resistance of the sensor contacts using a multimeter.
If everything is in order, put the module back in place and check the operation of the Samsung washing machine. DIY repair completed.

Repairing the heating element of a Samsung washing machine can be done by hand, but you need to take into account that this is somewhat more difficult to do than in the case of other brands of machines. We mean, first of all, the inconvenient location of this module. For other brands of automatic machines, it is enough to remove the back wall and the heating element is at your disposal. By cars Samsung heating element is located at the front, which means that laborious work will have to be done to dismantle the front wall.

Because of this nuance, experts often criticize Samsung washing machines, because ten is a part that breaks relatively often. Dismantling the front wall of the machine is associated with the risk of a new malfunction: you can break the cuff, break the clamp, break off the plastic pins so that the front panel will not snap into place later, you can finally tear off the sensor wires of the hatch locking element. We will try to act like professionals and remove the front wall without loss.

First, unscrew the lower bar of the front wall of the washing machine.
We take out the cuvette for the powder, there are several fasteners in the niche for the cuvette, we unscrew them.
Remove the top cover of the washing machine as described above.
We unscrew all the screws holding the control panel, remove the control panel.
We take a screwdriver and carefully pry off the collar of the washing machine cuff and remove it (The cuff is an elastic band located around the hatch).
We unscrew the two bolts securing the door locking device and take it out without forgetting to disconnect the sensor wires.
Pull out the cuff very carefully.
We unscrew the rest of the fixing bolts and remove the front wall.

The front wall of the washing machine has been removed - the malfunction can be repaired. First, let's check the resistance of the heating element contacts. To do this, we take a multimeter, connect the probes to the contacts and look at the value on the display. If no faults are found, dismantle the heating element. To do this, unscrew the fastening element, which is located in the middle between the contacts of the heating element, and then, with swaying movements from side to side, we pull the heating element out of the tank.

In most cases, a large layer of scale forms on the heating element, which destroys the module. If the scale has already formed, the heating element must be replaced. Such malfunctions are not eliminated, but for the future, remember that you need to use water softeners and then everything will be fine.

Important! When changing the heating element, do not forget to change the sealing gum, it comes with a new heating element.

In conclusion, we note the repair of Samsung washing machines can be done by hand, especially when it comes to typical malfunctions that we touched upon in this article. The owners of these models of washing machines most often encounter such breakdowns, however, no one is immune from surprises. If a malfunction occurs that you cannot correctly identify and eliminate, contact the specialists.

Troubleshooting Samsung washing machines S821GW / YLP, S821GWL / YLP, S821GWS / YLP, S621GWS / YLP. Service manual.

1. Do not let the customer repair the product themselves.

◊ This could result in customer injury or product damage when the device is serviced by unqualified personnel.

2. Disconnect power to the device before servicing.

◊ Be aware of the possibility of electric shock.

3.Do not use tees or extension cords.

◊ The electrical outlet may be overloaded, which could cause overheating.

4. Check the plug or outlet for damage.

◊ Replace them immediately if damaged. (It may cause electric shock or fire)

5. Make sure the product is reliably grounded.

◊ Lack of grounding can cause electric shock.

6. Do not use water or products based on water to clean the interior of the product.

◊ this may cause electric shock / fire or shorten the life of the product.

7. Wire harnesses must be dry and properly connected for repairs.

◊ it is necessary to exclude any external influence.

8. Remove dust and dirt in the product, especially from electrical components and connections during servicing.

◊ Protection against the possibility of fire due to breakdown, etc.

9. Check for water marks on electrical parts, connections, etc.

◊ Replace parts and / or wipe dry with water.

10. Verification of correct assembly after service.

◊ Check that the product was assembled in the same condition as before servicing.

11. Do not pull on the power cord, only unplug it by holding the plug.

◊ Beware of electric shock or fire if the power cord is damaged.

12. Unplug the power cord from the outlet when the washing machine is not in use.

◊ Beware of electric shock or fire during lightning storms.

13. Do not use or place flammable materials (including gasoline, alcohol, thinner, etc.) near the washing machine.

◊ Flammable materials can cause explosion or fire from sparks.

14. Do not place containers with water or wet laundry on top of the washing machine.

◊ Doing so may result in electric shock or fire, or shorten the life of the product if water seeps into the washing machine.

15. Do not install the washing machine where it can be exposed to snow or rain, etc.

◊ Doing so may cause electric shock or fire and shorten the life of the product.

16. Do not press control buttons with sharp objects such as pins, needles, etc.

◊ This can lead to electric shock or other problems.

17. Check that the washing machine is level, horizontally on a hard floor and installed correctly.

◊ Vibration can shorten the life of the product.

18. Always use connectors to connect wires.

◊ If the wires are connected without connectors, it can lead to short circuits.

19. When servicing and opening the washing machine, place the notebook on the floor and tilt it slowly on its side.

◊ If the washing machine is placed on the front panel, internal components may be damaged.

We use 5 user safety devices to keep your washing machine safe.

In case of uneven distribution of the laundry, to prevent noise and vibration, the imbalance detection sensor helps to distribute the laundry evenly and continue the spin process.

The device works as soon as the water level exceeds 2/3 of the door level, the supplied water begins to drain automatically, an overflow error message is displayed on the panel.

To prevent exceeding the set temperature, THERMISTOR constantly measures the temperature of the water in the machine and ensures the operation of the machine at the temperature set by the user.

In the event of a THERMISTOR malfunction or its incorrect operation, if the TEN overheats, the built-in protective thermal fuse automatically cuts off the power supply, ensuring safe operation.

To protect delicate garments, the machine monitors the temperature of the water entering the tank. If the temperature is above 50 ° C for the Wool and Delicates cycles, the machine will drain the water and an error message will be displayed on the panel.

Rice. one Location of the washing machine components

Rice. 2 Location of the washing machine components

Detergent dispenser drawer
Indicator panel
Displays washing progress and error messages on LED lamps.
Washing program selection button
Press the button to select one of the six available wash programs.
.
Temperature selection button
Press the button several times to cycle through the available water temperature options
(cold, 40 ° C, 60 ° C and Bio 60 ° C).
* Bio 60 ° C: To increase the efficiency of washing, heat for 30 minutes.
Spin speed selection button
Press the button several times to cycle through the available spin speed options.
Start / Pause
Click to pause and restart the program.
(On / Off) button (On / Off)
Press once to turn on the washing machine, press again to turn off the washing machine.
If the washing machine is left on for more than 10 minutes without any button operation, the power will automatically turn off.

Once turned on, the auto power off function will automatically turn off the power if you do not press the function select button within 10 minutes
After selecting the Auto Power Off function, it will automatically turn off the power if you do not press the Start / Pause button within 10 minutes
5 minutes after the end of the last function, auto power off will automatically turn off the power unless you press the function select and start button again.

If the door is opened during operation, all operations are paused and an open door error message will be displayed and an error beep will sound.

The door opening error can be cleared by closing the door. Machine operation will resume from the interrupted place.

If a power failure occurs during operation, the operation information will be stored in the machine memory (EEPROM), as soon as the power is restored, operation will continue.
When the power is restored, the washing machine will start from the interrupted place, for rinsing / draining the process will start over.

Rice. 4 Power failure compensation function

This function starts working when the heating element does not work correctly (the function starts checking the heater 1 minute after the heater starts working)
Initial value (A1) of thermistor compared to value (A2) of thermistor after 2 minutes (Y = A2-A1)
- If after 10 minutes the temperature difference (Y) is less than 2 ° C, the LEDs “40 ° C / Bio60 ° C».
The initial value (A1) of the thermistor compared to the value (A2) of the thermistor in 2 minutes (Y = A2-A1) - If the temperature difference (Y) increases by more than 4.5 ° C (0.2148V) in 2 minutes, on the panel LEDs “cold / Bio60 ° C».
In this case, if the error "40 ° C / Bio60 ° C"(Heater does not work) and"cold / Bio60 ° C»(Overheating) messages are indicated on the display and all work processes are stopped.
The heater continues to operate for the time specified by the program; if heating is canceled, the rest of the wash continues without heating.

After the end of the initial stage of water filling, the laundry absorbs part of the water, the water level drops, and it becomes necessary to add additional water until the level stabilizes.

Video (click to play).

The processor determines the amount of loaded laundry based on the number of additional water additions and starts washing after the water level has stabilized. In the "Cotton" modes, if additional water additions occur more than 3-4 times, the processor sets the default condition “high water level”, if water was added 1-2 times, the average level is set, if 0 - low water level. Heating time and rinsing time depends on the above data.

Rate the article:

Grade 3.2 who voted: 82