Do-it-yourself Thomas Twin TT repair

In detail: do-it-yourself Thomas Twin TT repair from a real master for the site my.housecope.com.

For renovation ON buttons of the THOMAS TWIN tt vacuum cleaner we do a few simple operations:

1. Unscrew 6 screws from the bottom of the vacuum cleaner. The 2 screws are hidden under the filter cover on the back of the vacuum cleaner.

2. Remove the case. The wires do not need to be disconnected. If you still decide to disconnect the wires, mark which one goes where.

3. Unscrew the self-tapping screw that holds the board under the on / off button on one side. On the second side of the board, remove the metal clip located on the flat plastic pin by simply prying it with a flat screwdriver with a little effort.

4. On the board we find the button on which the vacuum cleaner toggle switch presses.

5. With a cotton swab dipped in alcohol (you can use cotton swabs), abundantly moisten the space around the movable black button and press it ten to twenty times.

6. After that we screw everything back.

7. When reassembling, make sure that the rubber gaskets that grip the pump on both sides do not move or fall.

It is a little inconvenient to combine the “tape measure” (the disk on which the wire is wound) and the grooves in the upper part of the case. Just take your time and everything will work out.

Repairing the ON button of the THOMAS TWIN tt vacuum cleaner is the simplest breakdown. In more difficult cases, you will be helped by the specialists of ELECTROSAN sot.t. 22-44-28

After five years of operation, the vacuum cleaner began to howl harshly during operation. The sound is clear, the bush hummed. Waiting for it to crumble and smoke was somehow not a hunt. I decided to take a closer look at the patient. The price of the new engine on the servicemen's website was not pleasing, almost a third of the cost of the vacuum cleaner. Doesn't seduce against penny bearings.

Video (click to play).

A study of the resources showed that there are disassembly instructions, but only text. Filmed the disassembly process itself. No particularly difficult moments have been identified.

So let's get started. We unscrew the two screws and remove the top cover, so that it does not interfere

Next, turn the vacuum cleaner over and unscrew the 6 screws on the bottom cover. Two of them are located under the air intake filter cover.

We turn over and halve the case, there are no latches and latches, you just need to shake it and it will turn out

We unscrew 4 large screws and one small one on the cover that covers the engine. We take out the wires from the mounts and slide the cover along the wires

The engine is simply removed from the housing.

Next, we follow the instructions found on the Internet.

Disassembled according to this instruction for Thomas Twin TT with my comments

1. Remove the motor from the black casing - flow divider by unscrewing 4 screws and removing the power supply terminals from the motor (write down where they were). The terminals are pulled together by light rocking.

2. Turn the engine upside down (galvanized part down).
3. Carefully pull off (as if contouring) the black plastic casing-pipe, pulling, one by one, the latches. You need to shoot carefully, I broke a nail, for example. I overdid it a bit.

4. Remove the clamps from the brushes by bending the clips on the terminals with a screwdriver.
5. Remove the brushes by bending the bronze clips to the brush body. My brushes were just pressed with springs. I squeezed them out with my finger and just pulled the brushes out of the top cover.

6. Put a socket wrench on the nut, from the side of the turbine, unscrew the fan impeller by hand, throwing a rag over it, if there is no special wrench. Left-hand thread, i.e. unscrew clockwise. There is an aluminum washer under the impeller, do not lose. I didn't have the puck, so I couldn't lose it. The impeller took off without problems

7. Remove the white plastic bearing holder (although, brushes too) by unscrewing the 2 screws in the grooves. There is a spring washer on the bearing, remember its position. The lid was not on screws but on a nut, although it was not important.The position of the spring washer is easily identified by the grooves in the rubber bearing cap. In my opinion, it is better to install the washer back with support on the unworked places.

and here is the washer and nuts

8. Remove the stator.
9. Unscrew the aluminum nut from the turbine side (right-hand thread). Try to do this by holding the rotor in your hand. In my case, I had to grip the rotor in a vice, since the thread was rusted. Plugging the thread for 2 days with a mixture of oil and kerosene did not help.

10. Place the product in its original position. There is a retainer under the rotor, above the bearing, we remove it gradually, moving each petal upward a little, in a circle, until the retainer washer comes out completely. Remove the rotor. Remember the location of the parts in the bearing assembly.

11. Disassemble the turbine, if required. - Bend the latches around the circumference. Next, you need 4 hands. With both hands, hold the turbine in suspension by the plastic part, and with it to the top, gradually knock the galvanized cup down with an aluminum pin in a circle, lightly hitting it with a hammer.

Interestingly, the top bearing turned out to be 607-z, although all sources write that 608-z.

21 December 2014 18:30:46
Reviews: 0
Views: 7969

In this article, we will look at the malfunction of the vacuum cleaner. Thomas TWIN T1.

The manifestation of this malfunction is as follows: a vacuum cleaner Thomas when plugged in does not work.
1. Make sure that our vacuum cleaner is not connected to the power supply.
2. Let's examine our vacuum cleaner.
3. Open top cover.

4. Remove from the Thomas vacuum cleaner Hepa inlet filter.

5. Extract container for water together with a filter sponge.

Read also: DIY furrier repair

6. Inspect the Thomas TWIN T1 vacuum cleaner on both sides and locate the hardware that connects the plastic housing to each other. Finding fasteners , unscrew it with a screwdriver.

7. This model of vacuum cleaner Thomas TWIN T1 has hidden fasteners so open the cover, under which there is an output filter and unscrew the fasteners so that we can separate the case.

8. Separate the top cover from the bottom of the Thomas vacuum cleaner.

9. Carefully disconnect the connectors on the power cord .

10. Please note that the TWIN T1 vacuum cleaner motor is located in the upper part of the body, on which there is also electronic module , a branch pipe for water.
11. Inspect how the vacuum cleaner motor housing is secured and unscrew fasteners .

13. Take the vacuum cleaner motor out of the housing, remove the noise insulation and sealant .

14. Required new motor for the Thomas TWIN T1 vacuum cleaner which can be purchased at our store .

15. Install the vacuum cleaner motor into the plastic housing.

16. Assemble the Thomas TWIN T1 vacuum cleaner in the reverse order, check the inlet and outlet filters for suitability, reinstall them, pour water into container , close the top cover, plug the power cord into a power outlet, and press power button ... Check the performance of the vacuum cleaner for suction of air through telescopic tube .

Message aspirantvisav »06 May 2012 12:08

Message elremont »06 May 2012 12:12

Message transfor »06 May 2012 12:48

Message aspirantvisav »07 May 2012 09:51

Message vikshi »08 May 2012 12:20

Message elremont »08 May 2012 12:34

Message aspirantvisav »09 May 2012 13:14

Message aspirantvisav »09 May 2012 13:56

Message elremont »09 May 2012 15:36

Message vikshi »12 May 2012 01:36

Message elremont »12 May 2012 12:47

Message ILYA120 »14 May 2012 15:37

Message aspirantvisav »16 May 2012 02:29

Message solary "31 Oct 2012 21:52

Message ig2v »05 Nov 2012 11:10

Message RK »05 Nov 2012 15:03

Message RK »05 Nov 2012 15:05

Message ig2v »05 Nov 2012 19:21

Message RK »06 Nov 2012 11:28

Message solary »13 Jan 2013 03:10

Message krokodil »16 Jan 2013 23:52

Message valentin_333 »17 Jan 2013 17:49

Message sharki »26 Feb 2013 15:03

The power button also stopped working, alcohol helped, but not for long, for about a month, bought a button that was on the board for $ 1, and asked a friend to replace it, we have a button size of 12x12x7 (height), but I bought 12x12x5, I had to lengthen it above.

I disassembled the old button, and in principle there is nothing difficult there, you could just disassemble it and clean up the contacts.
Photo below

Message sharki »26 Feb 2013 20:06

Message Manyushka »23 Apr 2013 21:42

Message savrasoff »19 Jul 2013 10:13

Message transfor »19 Jul 2013 13:34

What to do if your thomas tt vacuum cleaner stops turning on? In this article I will tell you how to repair your Thomas vacuum cleaner yourself, namely, repair the power button at home.

For a thomas tt vacuum cleaner of this model, the main reason why it does not start is the power button, which is located on the control board. Such a repair is not particularly difficult, and then I will tell and show you how to make this repair with your own hands.

For repairs you will need: a Phillips screwdriver, a soldering iron and consumables for soldering.

We plug the soldering iron into the network while it heats up, take a Phillips screwdriver, unscrew 6 screws that are at the bottom of the thomas vacuum cleaner, 2 of them are under the filter cover.

Next, we need to remove the top of the Thomas Twin tt case.

The control board with which we will carry out repair work is circled in red. The board is attached with 2 screws that we need to unscrew.

Important! There are 3 wires connected to the control board. When you disconnect them from the board, remember how they were connected, or better with a marker, sign where which wire was connected, because if you connect it incorrectly, when you turn it on, the semiconductor will immediately burn out, which regulates the power of the thomas vacuum cleaner. Take a Phillips screwdriver, unscrew the bolts and remove the control board.

The Thomas vacuum cleaner start button is soldered on the back of the control board, we need to replace it with a new working one.

You can buy a similar button in any radio store, as it will not be difficult for you to find it. We take a preheated soldering iron and solder the old button in order to replace it with a new working one.

After we have replaced the button on the control board, it can be replaced. We connect the wires to it and assemble the Thomas Twin tt vacuum cleaner back.

We connect all the terminals, assembled the vacuum cleaner and turn it on. Our twin tt vacuum cleaner started up the first time, which means that this repair of the thomas twin tt vacuum cleaner was successful, and again you can continue to use your house assistant. As you can see from this material, repairing a Thomas vacuum cleaner with your own hands, namely, repairing the power button, is not difficult, and you can make repairs yourself at home.

Three years ago I bought a Thomas Twin T2 Aquafilter vacuum cleaner. Today the pump stopped working, disassembled, looked, assembled - it does not work. Unfortunately, there were no clamps. to remove it and check it separately. But one of these days I will buy and check.

There are such a small number of pictures. To remember what is happening.

In espresso makers, similar pumps are installed, except that there may be more power. But to find a killed coffee maker, I think, is not a problem.

Yes, they are many where similar, but there was a question with an outlet thread, and I could not find an answer to it. It took a month to find when it was necessary. As a result, bought from Thomas, the price is fun. And I'll play with the old one. And there will probably be a video of how to fix it. For for.

This site uses Akismet to combat spam. Find out how your comment data is processed.

Like ♥ and Subscribe to the channel.

On this channel of the Wizard, you will see how to repair and install what. The master is engaged in the installation of repairs.

Here is the disassembly of the vacuum cleaner to the root.

A brief description of the elimination of the common reason for the failure of the Thomas t2 vacuum cleaner, the start button.

First debut video - Repair of the start button of the Thomas Twin TT pilossus at once. I'm just learning. ...

Overhaul of the Thomas dust pump.

THOMAS Twin TT after six and a half years of use. review, I will tell you what and how, as well as analyze it and show it.

Do-it-yourself vacuum cleaner repair Thomas twin tt does not turn on.

you want to receive a video on how to change the filter in a washing vacuum cleaner thomas twin tt aquafilter thomas twin tt aquafilter.

it's difficult when you don't know how, having a puller you will have to ruin a couple of motors to understand how to do it right.

Elimination of malfunctions in the dosing pump of the Thomas Vestfalia washing vacuum cleaner. I apologize for the reservations and.

Buy the engine for the Thomas vacuum cleaner - —————————————- The engine for the Thomas vacuum cleaner (Thomas).

Analogues for repairing the Festool midi vacuum cleaner.

Vacuum cleaner Thomas TwinTT. Filter replacement, repair.

Video on how to properly care for the Thomas TWIN XT vacuum cleaner with an aqua box system and similar vacuum cleaners. ...

A simple way to increase the suction power of a vacuum cleaner, or rather to improve its "direct operation" :)) This is a problem.

Ulka pump repair our website

You can buy a motor for a vacuum cleaner on our website Available motors for Samsung, LG, Bosch, Thomas, Zelmer.

Vacuum cleaner repair or just head cleaning. From dust and hair.

How to fix a vacuum cleaner switch with your own hands.

Like ♥ and Subscribe to the channel.

The story of how I repaired the motor of my vacuum cleaner is just an effort of thought. How.

Turbo brush for the THOMAS TWIN TT AQUAFILTER vacuum cleaner Watch my videos on topics: Unboxing:.

Like ♥ and Subscribe to the channel.

And again the Samsung Twin vacuum cleaner is under repair. The engine didn't survive. From what and why, this happened, see in.

Like ♥ and Subscribe to the channel.

They brought a Samsung twin vacuum cleaner to the repair, with a glass instead of a bag, with a complaint about the twitching of the vacuum cleaner and grinding.

Dismantled the vacuum cleaner, washed the engine.

In this video I will show you how to disassemble the telescopic tube.

Based on numerous questions to the previously published video, I made a more detailed video about the repair.

A little later - a true story.
First, the question - who has this device: - with what force do you spray water from the nozzle onto the carpet?
The fact is that my new unit sprays a little harder than a manual flower sprayer.
Therefore, it is interesting - where are the promised 4 bars.? Or is it at the outlet of the pump 4, and is "lost" on the way?
Or is it a malfunction - and “hello service”.

This is normal work and it should be. We have the same thing, it's enough to wash the dirt.

Go - they said that the pump was clogged with Styrofoam. After cleaning, I gave out what was written.

LMA wrote:
This is normal work and it should be. We have the same thing, it's enough to wash the dirt.

Yes, to see it is so conceived

- measured it on - it pours, even more than the passport norm (0.8 l / min versus 0.7 l / min).
Andy52280 -thank you, I know this story,
She can be said and prompted to "showdown"

... But more on that later.

A question for connoisseurs. I am the owner, this device works perfectly, there is a small caveat - it is a dog leaking! Those. when working under it, a puddle of clean water is formed, can anyone come across? It looks like some kind of loose connection, it is difficult to disassemble it (it flows from the purchase, but it’s far from the service).

Tony wrote:
it is difficult to disassemble it (it flows from the purchase, but to drag it far into the service).

You put 6 screws up with your “belly” and a long Phillips screwdriver. You twist it.
There are no seals.
Many new things will be revealed

.
Are the two screws on the pump tightened up?

How do I know 2boga. I haven't dissected it yet

The promised story about the vacuum cleaner.
I was “familiar” with two. The first was not for long - just a “nodding acquaintance”. I use the second.
The story is a little in the spirit of the "Consumer" magazine, and may Natalia Panfilova forgive me for this "addition".

Is your TV, radio, mobile phone or kettle broken? And you want to create a new topic about this in this forum?

First of all, think about this: imagine that your father / son / brother has an appendicitis pain and you know from the symptoms that it is just appendicitis, but there is no experience of cutting it out, as well as the tool. And you turn on your computer, access the Internet on a medical site with the question: "Help to cut out appendicitis." Do you understand the absurdity of the whole situation? Even if they answer you, it is worth considering factors such as the patient's diabetes, allergies to anesthesia and other medical nuances.I think no one does this in real life and will risk trusting the life of their loved ones with advice from the Internet.

The same is in the repair of radio equipment, although of course these are all the material benefits of modern civilization and in case of unsuccessful repairs, you can always buy a new LCD TV, cell phone, iPAD or computer. And for the repair of such equipment, at least it is necessary to have the appropriate measuring (oscilloscope, multimeter, generator, etc.) and soldering equipment (hair dryer, SMD-hot tweezers, etc.), a schematic diagram, not to mention the necessary knowledge and repair experience.

Let's consider a situation if you are a beginner / advanced radio amateur soldering all sorts of electronic gizmos and having some of the necessary tools. You create an appropriate thread on the repair forum with a short description of “patient symptoms”, ie. for example “Samsung LE40R81B TV does not turn on”. So what? Yes, there can be a lot of reasons for not switching on - from malfunctions in the power system, problems with the processor or flashing firmware in the EEPROM memory.
More advanced users can find the blackened element on the board and attach a photo to the post. However, keep in mind that you are replacing this radio element with the same one - it is not yet a fact that your equipment will work. As a rule, something caused the combustion of this element and it could “pull” a couple of other elements along with it, not to mention the fact that it is quite difficult for a non-professional to find a burned-out m / s. Plus, in modern equipment, SMD radioelements are almost everywhere used; The subsequent restoration of which will be very, very problematic.

The purpose of this post is not any PR of repair shops, but I want to convey to you that sometimes self-repair can be more expensive than taking it to a professional workshop. Although, of course, this is your money and what is better or more risky is up to you.

If you nevertheless decide that you are able to repair the radio equipment on your own, then when creating a post, be sure to indicate the full name of the device, modification, year of manufacture, country of origin and other detailed information. If there is a diagram, then attach it to the post or give a link to the source. Write down how long the symptoms have been manifesting, whether there were surges in the supply voltage network, whether there was a repair before that, what was done, what was checked, voltage measurements, oscillograms, etc. From a photo of a motherboard, as a rule, there is little sense, from a photo of a motherboard taken on a mobile phone there is no sense at all. Telepaths live in other forums.
Before creating a post, be sure to use the search on the forum and on the Internet. Read the relevant topics in the subsections, perhaps your problem is typical and has already been discussed. Be sure to read the article Repair strategy

The format of your post should be as follows:

Topics with the title “Help fix the Sony TV” with the content “broken” and a couple of blurred photos of the unscrewed back cover, taken with the 7th iPhone, at night, with a resolution of 8000x6000 pixels are immediately deleted. The more information you post about the breakdown, the more chances you will get a competent answer. Understand that the forum is a system of gratuitous mutual assistance for solving problems and if you are dismissive of writing your post and do not follow the above tips, then the answers to it will be appropriate, if anyone wants to answer at all. Also keep in mind that no one should answer instantly or during, say, a day, no need to write after 2 hours “That no one can help”, etc. In this case, the topic will be deleted immediately.
You should make every effort to find a breakdown on your own before you get stumped and decide to go to the forum. If you outline the entire process of finding a breakdown in your topic, then the chance of getting help from a highly qualified specialist will be very great.

If you decide to take your broken equipment to the nearest workshop, but do not know where, then perhaps our online cartographic service will help you: workshops on the map (on the left, press all buttons except “Workshops”). You can leave and view user reviews for workshops.

For repairmen and workshops: you can add your services to the map. Find your object on the map from the satellite and click on it with the left mouse button. In the field “Object type:” do not forget to change to “Equipment repair”. Adding is absolutely free! All objects are checked and moderated. A discussion of the service is here.

THOMAS Twin TT after six and a half years of use. a review, I will tell you what and how, as well as disassemble it and show how I repaired it with my own hands.

The class has been working for 6 years for 5 years and Thomas is dead, the parquet master is complete garbage. Everything was done on a special basis to break down in less time. Even twint tt and that show

Sychikhin Alexander Hace un mes

Indeed, the price of the cost is not justified. Also, due to the multi-stage filtration, it is difficult to operate. Not every mistress can entrust such a device without a training course)))

The price has not changed, but the ruble rate has fallen by 2 times! ))) That is, it became 2 times cheaper than it was

Do you think it's worth taking it for 5500?

Stepan Filippov Hace un mes

A simple overview of Hace 2 meses

hunterpro88 Well, if everything works, it's worth it.

Yasur Coments Hace 3 meses

Thanks for the vidos. We also have this vacuum cleaner for 6 years, a year ago the wet cleaning system broke down, went to the store where we bought the vacuum cleaner (2 times) to check the vacuum cleaner and solve the problem. In general, there was no benefit from the store. Then, I noticed that the fitting on the water supply hose broke, they ordered it from Krasnodar for 400 rubles, changed the fitting, but the problem with wet cleaning did not dare.

see my comment. It seems that he did not come here.

The pump sticks there. Branded detergent has the feature of gluing the piston to the walls of the pump. See the video for disassembling the vacuum cleaner, then simple. unscrewing the pump from the coil and dividing (not disassembling!) it into two parts by turning it around its axis, pull the piston back and forth. If initially it stuck, you will immediately see. Otherwise, disassemble the pump, wipe it with silicone grease! Be attentive to the order of disassembly and assembly.

A simple overview of Hace 3 meses

You are welcome. The best thanks is a subscription and if you share my videos

Thomas washing vacuum cleaners are known for their versatility and quality of work (here they are not inferior even to separator vacuum cleaners). There are so many models of this company that you can choose a unit for any type of cleaning - both classic dry cleaning, and for washing windows or cleaning furniture upholstery.

The most popular models of washing vacuum cleaners are devices with an aquafilter of the Twin TT, T1, T2 series, as well as vacuum cleaners with a Hygiene bag filtration system, which allows hygienic dry cleaning. But, like any device, even such high-tech vacuum cleaners can break down or fail, even if you regularly change the filters for the vacuum cleaner.

Why did it happen? The reason may be improper storage of the vacuum cleaner, improper use of the device (when the vacuum cleaner is pulled by the hose to move or abruptly remove the hose after completion of work)

Diagnostics... The hose can break in two places - near the handle (this usually happens with a vacuum cleaner with an aquafilter) or near the junction with the vacuum cleaner. It is difficult not to notice the break in the hose - firstly, the place of the break is always visible, and secondly, the vacuum cleaner will let dust through and stop sucking in dirt.

Repairing a vacuum cleaner hose, as a rule, does not make sense, and it is best to completely replace it and buy a new one (this is especially true for Karcher car vacuum cleaners). Depending on the model of the vacuum cleaner, the price of the hose starts at $ 40. For example, such spare parts for the Twin TT model will cost 60-70 dollars.
to the menu ↑

Diagnostics

The repair begins with checking whether the device hums when turned on.If it buzzes, it means that somewhere along the path of the air there is a blockage. Where it formed, you can determine in this way - remove the hose and see if the vacuum cleaner sucks air through the hole for the hose. Doesn't it suck? This means that a blockage has formed inside the device (this often happens with washing vacuum cleaners).
The next step is to clean the HEPA filter, because it is he who is responsible for fine cleaning and is installed in many Thomas models. The HEPA filter must be rinsed and cleaned from blockages. If the filter cannot be cleaned, you need to buy and install a new one.
The third stage is checking the work, which is carried out after the complete drying of the HEPA filter.

As a rule, it is difficult to independently carry out such a complete diagnosis of vacuum cleaners and repairs, so the best advisor in this matter is a specialist. How much will his services cost? For example, diagnostics of the operation of Thomas vacuum cleaners or Philips washing vacuum cleaners will cost $ 25-35, replacing the HEPA filter in the same Twin TT vacuum cleaner will cost $ 20.
to the menu ↑