DIY repair of cracks in the soles of shoes

In detail: DIY repair of a cracked shoe sole from a real master for the site my.housecope.com.

Is it worth carrying to the workshop or is it easier to buy new ones right away?

Even if you seal the crack very well using the best materials (which in itself is not cheap), you will soon get a new crack in the immediate vicinity of the repair site.

In theory, you can replace the entire sole. But, firstly, it is unlikely that you will be able to find the right one, and secondly, you will have to change both soles.

Therefore, advice aimed at buying new shoes is the most efficient and cost-effective. Now is not the beginning of the season, you can find a serious sale. In some stores, the "last pair" is sold for 40-50% of the regular price. Spending time searching is better than a hopeless repair.

A detailed story about how to repair shoes yourself was published in more than ten issues of the magazine in 1997 and 1998. This time we bring to your attention a method by which you can “defeat” a common “disease” of shoes - a crack in the sole.

Foam rubber soles often crack. In most cases, gluing the lining does not give a good result: the weakened sole continues to get wet, and the lining quickly comes off. Shoes with still quite decent tops have to be thrown away. However, there is an easy way to repair such shoes at home.

Thoroughly clean the crack from dirt, sand the inner surfaces with an emery cloth and degrease with gasoline or acetone. Cut the edges of the crack, that is, around the crack, cut the edges of the sole to a width of 5-7 mm. The groove depth should be about 1 mm. Cut a strip from the old bicycle tube with a width equal to twice the crack depth + 10-15 mm. Clean the strip, degrease and coat with rubber glue, glue No. 88H or Moment. On one side, spread the strip over the entire surface, and on the other, leave dry edges 5-7 mm wide. Bend the sole so that the crack opens, grease its inner surface with glue and, without covering the crack, let the glue dry for 10-15 minutes. After that, carefully insert a strip folded in half into the crack, straighten the sole, and press the remaining edges of the strip firmly against the sole. Leave the shoe under load for a day. Experience shows that after such a repair, the shoes serve for a rather long time.

Video (click to play).

Is it possible to restore the sole of women's shoes at home?

How to Repair a Cracked Outsole? Crack along the entire width of the sole.

Unfortunately, not always expensive shoes made of genuine leather are of high quality, if you do not take into account when buying what material the sole is made of.

The thick sole ("tractor" sole) of the winter boots burst at the bend. The reason is the weather, the thaw, then the temperature drops sharply to -20 degrees. They took it for repair, but the master immediately warned that there were no guarantees, the sole might crack after a while next to the first one. All the same boots with heels

The spouse decided to repair it himself. On advice, I chose Desmokol elastic glue (suitable for repairing winter shoes). The shoes were dried, cleaned of dust, degreased with acetone, and given time for the product to evaporate. I applied the glue according to the instructions: on the inner surface of the cracked sole, I applied a layer of glue, withstood the time, as advised according to the instructions, up to 10 minutes. Then I applied another layer of glue, because the sole is made of a porous absorbent material, withstood the glue for another 8 minutes. You need to wait until a glossy film appears.Then the glue was heated with a hair dryer and the glued surfaces were pressed firmly. When gluing surfaces with Desmokol glue, the main thing is to press as much as possible, and not the time for holding under pressure.

Repaired boots with thick soles I put on shoes only two days later, while everything is in order.

We all love beautiful and expensive shoes. And we get very upset when it breaks, bursts, or when something similar happens to it. How to repair the sole of a shoe if it has burst is a very frequent question on various forums, because no one wants to throw away shoes without trying to restore them. And going to the master is not always beneficial in terms of unplanned expenses. There are a couple of methods with which you can solve the problem with your own hands, it is about them that will be discussed in this article today.

Let's take a look at the main reasons the outsole bursts, and more:

The first is an uncomplicated problem in the material from which the sole was directly made. For example, PVC outsole often bursts, it lacks elasticity and strong bends can seriously harm it.
The second reason is the thickness of the sole itself. Often, when making thick soles, polyurethane foam or microporous rubber is used. So, if your sole is exactly like this, most likely it will burst. Yes, such a sole is resistant to any bends, but it “doesn’t make friends” over time, as it begins to deteriorate.
The third reason, the most common, is to stumble upon something sharp. Note that even a small hole can be a big problem if you let things go.
The next reason is the time of year. It has been noticed that in winter, shoes crack more often, due to the effect of extreme cold weather on them and chemistry, which is sprinkled on roads from ice.

Let's talk about whether there is any way to warn yourself against such situations.

In order not to wonder how to repair the sole of a shoe if it bursts, follow these guidelines:

When buying shoes, carefully look at the sole so that it is elastic, made of high-quality material. Rubber and polyurethane soles will be preferred.
As strange as it may read, do not squat. Yes, yes, it is because of this that the damage to the shoes begins, the corners are torn and the sole bursts.

We pass directly to the solution of the problem itself.

So, what to do if the sole of your shoe bursts? - It is possible to solve a similar problem not even in one, but in several ways.

For this procedure, you will need:

glue "Moment";
Crazy Handles epoxy sealant;
means with polyurethane "Desmokol".

Important! Be extremely careful and attentive, as these products are toxic. In case of contact with mucous membranes, they must be immediately washed off with a stream of running water.

Since winter or autumn shoes in most cases have honeycomb soles, you will first have to deal with honeycombs. The rubber that covers them will have to be removed to such an area in order to remove all accumulated dirt from the holes.

Important! Sometimes the honeycomb is accessed from the side of the insole, which must be completely removed when cleaning the holes.

The honeycomb must be covered with small pieces of micropores and filled with silicone sealant, sealing well.
You need to wait for the sealant to dry and harden before sealing the cracked sole.
Next, a piece of rubber or micropores is cut out, which enters the hole - if it is bulky, or small holes are pressed in with a mixture of micropores sawdust and sealant.
The sole is cut out of thin rubber to the size of the shoe, glued with the help of an already prepared adhesive over the entire surface of the shoe.
Put shoes or boots under the press or other strongly pressing object.

Important! How long you need to wait until it is completely dry - look at the glue, everything is described in detail there.

From domestic adhesives, it is best to use epoxy, designed specifically for shoes. Its cost is low, so in comparison with new shoes, it is better to use glue.

How to repair a cracked sole on a shoe like this:

The edges of the hole in the sole must be thoroughly cleaned and degreased with a solvent. When everything is dry, apply a properly diluted epoxy.

Important! If the hole is large, it is necessary to lay a fiberglass mesh in it - it is called a serpyanka.

While the glue dries, to keep the sole flat, glue it with painter's glue.

Important! An excellent adhesive option is the American Seamgrip adhesive. Rubber boats are glued to them. If you manage to get it, it won't take long to part with your favorite pair of sneakers. This is the only glue that completely solves the problem of repairing a cracked rubber or polyurethane sole. Its cost is quite high and commensurate with new inexpensive sneakers.

Imported epoxy mixtures such as Done Deal are better than domestic adhesives, but the durability of sneakers when using them cannot be promised.

Step back from the crack about 5 cm towards the heel, draw a line parallel to it with a marker.
From the drawn line to the toe of the boot, clean the sole with sandpaper.
If there is a protector, carefully remove it from dirt.

Important! If you have ankle boots or shoes with a protector of more than 5 mm, then this method will not help you.

Having cleaned and degreased the crack itself with gasoline or acetone, glue it with good second-hand glue.
After that, draw the markings for the future thread grooves.
Using a boot knife, cut small grooves along these markings.
Pull the insoles out of the shoes and sew the sole along the cut marks with strong threads.
Apply an adhesive on top of the threads, and after it dries, cover the cleaned and degreased sole with a micropore or other material. Its thickness should be equal to the thickness of the tread and rubber, which was previously removed with sandpaper.

You can use a bicycle tube as a consumable to repair the soles of your shoes if they are cracked. For this:

Clean the inner surface of the crack and degrease it as usual - see above.
Using a boot knife, cut the edges of the sole to a depth of 1 mm, retreating by about 5 mm in both directions.
Measure the depth of the broken rubber with a ruler and add another 1.5 cm to this value.
Cut out a rectangle from the bicycle tube, the length of which corresponds to the length of the crack itself, and the width is the obtained value in millimeters.
Clean the resulting strip and degrease, coat with glue on all sides so that on one side the entire surface is covered, and on the other, leave the edges dry - about 5 mm.
Bend the cracked sole so that the defect is revealed. Treat it with glue and let it dry a little, preventing the edges of the crack from sticking together.
Glue the oiled rubber strip into the burst place, straighten it.

back to content ↑

Sole burst - how to glue? This question is relevant regardless of the season, because a crack in the sole of any shoe causes a lot of trouble. If you do not take the necessary steps in time, then you can even remain barefoot at the most inappropriate moment for this.

Repair of a burst sole belongs to the complex category, because you need not only to distinguish what material this or that sole is made of and with what glue it should be glued, but also to be able to assess the degree of complexity of the upcoming work. That is why, to solve the problem with cracked soles of winter boots, ugg boots, boots, sneakers, sneakers, your favorite summer sandals or shoes, you should contact the specialists of a shoe workshop. It is there that, in the shortest possible time and for a small fee, they will fix any problems related to shoes.

But if you are not ready to pay money or want to try your hand at being a shoemaker, then read this article and watch the video tutorial attached to it with step-by-step recommendations. No one is born a shoemaker; all abilities must be developed. So why not take action now? Moreover, you definitely have something to practice on, since you are looking for ways to solve a problem.

How to properly glue the sole with your own hands at home without the help of a master, as well as what you need to have on hand during the repair process, you will learn from this section of the article. Here you will also find recommendations regarding the order of work to eliminate gaps of varying complexity.

It is important to remember that all work should be done in a well-ventilated area and away from heat sources. You also need to take into account that the process of repairing a sole at home is a very dirty job, and it also requires concentration and enough time.

Read also: DIY LPG repair

It should be remembered that you only need to glue a clean sole. To do this, the entire shoe, and especially the sole, should be washed and dried dry, and only then proceed to repair it.

To fix the problem with the sole, the home craftsman will definitely need patience and:

boot knife;
sandpaper from "three" to "zero";
gasoline or any other composition for degreasing;
special glue;
awl;
matches or lighter;
hair dryer or heat source;
outsole of the right size, a piece of rubber or hard leather for the sole instead of the cut (damaged) area;
pencil or felt-tip pen
boot hook;
nylon threads.

Also, every home craftsman will need a heavy object that will act as a load, which will speed up the gluing time and improve the quality of work. In some cases, you may need a mini-grinder or a conventional angle grinder.

Take responsibility for the choice of glue! After all, the final result of the work will depend on its quality. On sale in household departments, choose shoe glue, and be sure to read the information about whether this substance is suitable for gluing the material from which the sole is made. You can also use a generic product.

If all of the above tools and materials are available, then you can start repairing the broken sole. Do not hope that the repair done by yourself will cost less than fixing the problem in the workshop, because all the necessary tools and substances will need to be purchased at the retail price.

There are several methods for restoring a cracked sole. The simplest of all is to stick a piece of rubber or other suitable material on the tear site. This method is suitable for shoes with smooth soles, such as sandals and shoes, but not for shoes with spikes and protectors, such as ankle boots or athletic shoes. Also, this method is not relevant for a sole made of foam rubber.

The second way to repair a cracked sole is to glue the area with a special glue or compound that melts the original sole material. Often this method is used to repair small cracks near the heel or along the welt of the shoe, as well as in some parts that are not subject to a high degree of stress, for example, at the heel or on the toe.

The third way to eliminate a hole in the sole is to partially replace the damaged area. This option is best suited for troubleshooting tread surfaces.

Some home craftsmen practice express repairs, but one can only guess about the longevity of the latter. For the most part, emergency measures should be taken only when there is no other way out. But at the same time, one should take into account the risk that a crack can form in the shortest possible time in any other place of the sole. This is due to the peculiarity of the distribution of the load when walking, and also directly depends on the quality of the roadway on which you have to move in shoes repaired in this way.

It is important to remember that most compounds for gluing rubber or polyurethane dry only after a day. That is why you can use shoes after repair only after this time.

The order of work to eliminate a crack in the sole will depend on the choice of repair method. Read more about each of them below.

The classic sole repair is used when repairing cracked polyurethane or ductile rubber soles.

To "reanimate" such shoes, you will need to have experience and skill, because you will not only have to glue the hole, but also sew it up with nylon threads using a boot hook and a sewing machine.

This method is suitable for smooth soles. The repair procedure is as follows:

Apply some quick-setting glue to the crack, and then glue the crack.
Apply a zigzag pattern to the sole as shown in the photo.
Cut along the lines with a boot knife or a hand-held machine with a disc.
Sew the sole with short stitches along the slits using an awl and crochet hook. Hide the knot in the edge of the "zigzag".
Singe the edge of the nylon thread with a match, and then glue it to the welt while still hot.

After completing a classic renovation, the shoes can be worn immediately. The disadvantage of this method is the complexity and the fact that the sole glued in this way will partially pass water, and the threads are very unstable to abrasion.

Repair with partial replacement of the damaged area is suitable if a crack is found on a smooth sole. The work is done in the following order:

Pour some glue into the cracked sole, and then hold the product for a while.
Degrease the area to be repaired with gasoline. Acetone can be used for leather soles.
Sand the crack with fine sandpaper, and then repeat the operation with coarse sandpaper.
Place the shoes on the material of the future sole, and then circle the area with a pencil or felt-tip pen. After that, remove the boot and cut the workpiece along the line using a boot knife. Do not rely on sleight of hand and do not trim around the product!
Use a sandpaper to erase irregularities in the material in the places of the cuts, and also process the side to which the glue will be subsequently applied.
Apply glue to the surface of the sole, rub it evenly with a wooden stick or silicone spatula. Perform a similar operation with the new heel. Dry the glue with a hair dryer or near the stove.
Apply the glue to the sole of the shoe again, and then attach the repair material to it.
Press the heel firmly against the sole and be sure to follow it. So that she does not budge.
Put a load on the product, then leave it for a day until the glue completely hardens.

After the time has elapsed, check that the patch is firmly seated. The operation described above should be performed on the second item of the pair (even if the sole is intact there), since it will be inconvenient to wear such shoes.

Repair of products with a high tread is carried out by analogy with the above method. But instead of a full patch, a small piece of material is used. The thickness of a piece of rubber for a patch should be equal to the height of the tread or be a few millimeters less.

This method of repairing a cracked sole is most suitable if the hole is longitudinal or transverse, but with smooth edges. It can also be used when the crack is shallow or only touches the tread itself.

The place in the area of the crack should be degreased, and then with the help of a grinder or a sharp boot knife, cut the thorns at a distance of about one and a half centimeters on each side of the break. After the operation, the place should be sanded and degreased. The patch is cut out to the full length of the crack. The width of the replacement piece cannot be less than two centimeters. Otherwise, the patch will simply fall off when walking.

Adhesive is applied to the insert and to the base sole. The principle of the work allows you to quickly eliminate the gap, so the shoes can be worn again in a day.

In the event that the crack is deep, you can try to cut a piece of the sole at the place of the hole, and instead insert a patch of molten nylon. It should be noted that this method is more suitable for foam or polyurethane soles than for rubber.

Express repair of the sole consists in applying a fast-setting glue or nylon melted to a liquid state in place of the crack. This method is not suitable for repairing the soles of sports shoes, but it is an excellent solution for resuscitating the soles of children's shoes.

All you need to do is degrease the crack by turning it outward. While holding the shoe in a bent position, pour the bonding material into the gap. Once the substance fills the pores, the sole will need to be repositioned. It is important to be able to firmly squeeze the bonding area until the adhesive sets. This usually takes fifteen minutes. After the operation, the shoes can be used almost immediately.

If, after following all the recommendations regarding restoring the integrity of the soles of your favorite shoes, the desired result is not obtained, then you should replace the shoe soles with new ones. Perhaps the sole in your boots was originally defective.

A crack in the sole of a shoe is not such a rare occurrence. This situation is especially unpleasant when the product warranty has expired. And although it will not be possible to carry out high-quality repairs at home, it is possible to partially revive the shoes. Sometimes repaired boots or boots can be carried in for a few more months.

Next, we will discuss the methods for self-repairing a cracked sole.

To repair a cracked sole, prepare:

shoe knife;

sandpaper;

a degreasing agent such as acetone;

instant glue that sets quickly;

hook;

threads.

Repair technology:

Sand the sole surface with sandpaper.
Bend the sole to open the crack. From there, you will need to remove all the dirt, the remnants of the old factory glue, using a boot knife.
Degrease the fracture site with acetone or gasoline, apply instant glue and press the walls together. Note: shoemakers advise using Desmakol or Nairit glue. To repair the sole, you can also take Moment rubber glue, Crazy Handles epoxy sealant.
The crack was sealed, but the repair is not over yet. In order for the shoes to be worn, the bursting sole must also be stitched. Using a pencil, draw zigzag lines across the entire crack. Using a manual grinder or a boot knife, make shallow grooves along the entire marking, about 2.5 mm. Now, using your crochet hook, sew the break, placing the stitches in the grooves you made. It is advisable to sew several rows of stitches: this will be more reliable, and the top layer will protect the lower threads from abrasion.

For work, you will need the following materials:

boot knife;

sandpaper;

acetone or gasoline;

a piece of a camera from a bicycle;

rubber glue.

As in the first case, the cracked sole must be cleaned and degreased. Use a boot knife to remove part of the sole: cut 5 mm along each edge of the crack. Maintain a cutting depth of approx. 1 mm.
The next step is to measure the depth of the fracture at the bottom. Add 15 mm to the resulting value - this will be the width of the strip that needs to be cut from the camera.
Clean the cut strip, degrease well, apply rubber glue to it. Completely coat one side with glue, on the other leave 5 mm of the edges of the dry surface.
Take your damaged shoes, bend them so as to reveal the crack as much as possible. Holding in this position and not closing for 10 minutes, coat the damaged area with glue.
Bend the prepared strip from the chamber in half and push it into the crack. The sole can now be straightened. Press down on the edges of the strip protruding from the crack against the sole surface. Place your shoes under something heavy for 24 hours.

To restore the sole, you will need a soldering iron and a piece of nylon.

First of all, remove the dirt from the shoes, clean and degrease the cracked surface.
Run a heated soldering iron inside the damaged area. The outsole material will begin to bubble and become sticky.
Next, you will need to rub the melted nylon into the damaged surface. To do this, place a piece of nylon on the burst place and press it down with a soldering iron. The nylon will melt, you just have to fill the crack with it until it completely disappears.

On a note: in order to straighten the melted nylon, during operation, use not the hot tip of the soldering iron, but the handle.

For winter shoes, you can repair a thick, cracked sole like this:

Clean and dry your shoes well. Clean and degrease the crack itself.
On the inner side of the break, apply a layer of Desmokol glue, let the product stand for 10 minutes.
Smear the crack again, as usually the material from which the sole is made is porous and easily absorbs various substances. Wait 10 minutes, during this time a glossy film forms on the surface.
Preheat the adhesive using a hot air gun and press down firmly on the sides to be glued.

Note: when using Desmokol glue, the gluing quality depends on the pressure on the surface.

Repair of winter shoes with a one-component, rubber-based polyurethane adhesive. You can take the Monument PVC glue. It is also often used to repair PVC boats.

Clean and dry well the surfaces to be bonded.
Bend the sole and walk with coarse sandpaper inside the crack, degrease.
Apply glue to both sides of the defective spot. Wait 15 minutes and apply another layer of adhesive. Note: all the time while the glue is applied and dries, the crack must be open.
After 5 minutes, straighten the sole, dock the surface to be repaired.
Next, to fix the sole, take a round stick, place it along and secure with a string. Place the shoes on the table, with the soles facing you, and warm them up with a hairdryer for 30 minutes. The heating temperature should be 60 ° C.

If you repair shoes in the evening, then in the morning you can already go outside in it.

If the sole of your shoes has burst, and the warranty period for the product has already expired, then it is most correct to refer the shoes to an experienced craftsman. In many cases, professional renovation allows you to extend her life from a month to a whole season, and sometimes even more. We already know how to get rid of the smell in shoes - folk remedies that are always at hand will help solve this problem. And how to repair shoes with your own hands with the help of available tools, we will now tell you.To fix a cracked sole at home, you will still need to acquire the following materials and tools:

boot knife;

emery cloth;

degreasing agent;

quick-drying glue;

boot hook and thread.

Is express repair possible in this case? If the shoes being repaired are without a protector, with a flat sole, then they can be repaired with their own hands and put on the same day. This is done like this:When sewing, more than one stitch should be sewn. This is necessary both in order to press the crack walls even more tightly, and so that the upper layers of the thread protect the former from possible damage in contact with a rough surface, for example, pebbles, glass, etc.Done - the cracked sole has been removed and the shoes are ready to be worn.If your shoe has a sole with a protector, then do-it-yourself express repair is impossible, because here you have to put an outsole on the sewn-up crack, which shoemakers call "prevention", and work with glue all over the sole. You will additionally need:

outsole material;

special shoe glue;

heating device - a powerful hair dryer or electric stove.

The algorithm of actions is almost the same as in the first method, but first you need to cut the tread from the broken sole to make it even and facilitate access to the crack.After that, follow all the same steps from 1 to 5, except that when sewing a crack, in this case, one layer of stitching will be enough, since additional protection will be glued on top of it.

Important: Do-it-yourself shoe repair with construction glue or universal "Moment" is impossible - these funds are completely inelastic. Shoemakers recommend using Dismakol and Nairit adhesives. They may have other trade names, but their composition does not change, and this is what the shoe masters call them. The former is more suitable for rubber and polyurethane products, and the latter is more suitable for leather products.

Draw a pencil around the sole of the product to be repaired on the outsole and make a pattern. This material should be thick enough to compensate for the thickness of the tread you cut from the outsole.

Image - DIY repair of cracks in shoe soles

Apply a suitable adhesive to the outsole and the degreased inner side of the outsole. Without gluing, withstand it for 15 minutes. Then apply a second coat and wait another 15-20 minutes. Then you need to activate the glue, heating it with a hair dryer or stove to 70-80 degrees.

While still hot, the outsole should be firmly pressed against the sole, preferably with a hard object.

That's it, DIY shoe repair is complete and the shoes are saved! But you can wear it only a day after the repair - then the glue will finally adhere and dry.

If your shoe has a burst sole, and the warranty period for the product has already expired, you can try to repair the shoe with your own hands with the help of improvised means. And how to do this, we will now tell you.

How to Repair a Cracked Sole - Method # 1

To fix a cracked sole at home, you will still need to acquire the following materials and tools:

Sand the surface of the sole with an emery cloth, stepping back five centimeters from the heel, and bend it in such a way that the crack can open up as much as possible. With a boot knife, we clean the inside of the remnants of factory glue and other dirt, and using acetone or another degreasing agent, it is imperative to prepare the crack for applying the glue and remove all possible grease.

Next, you need to glue the crack: apply quick-drying glue to its walls and press it together. Whether it is necessary to withstand the glue before gluing the crack, how long to wait for the glue to dry - it depends on the specific glue you will be using, so read the instructions carefully.

The crack was sealed - but it is still impossible to walk in such shoes, otherwise it will disperse again. Therefore, it will have to be sewn up.Using a pencil, make zigzag marks right across the entire crack.

Directly along these marks, with a boot knife or a manual mini-grinder, we begin to make cuts about 2.5 millimeters deep.

But now the crack must be sewn with your own hands according to these marks, laying the thread directly into the cuts. We hide the knot from the thread in the same hollows. However, sole sewing is different from ordinary sewing and is done with a boot hook. How to crochet is available in the following video:

Do you like our site? Join or subscribe (notifications about new topics will be sent to the mail) to our channel in Mirtesen!Sooner or later, the shoe starts leaking as the outsole bursts or cracks. If you want the pair to last for a long time, it is better to take the products to the workshop.Homemade methods will help to repair shoes only for a short period of time. But if you want to fix the products yourself, we offer methods on how to glue the soles of shoes at home.Before starting work, the sole must be cleaned, dried and degreased. For degreasing, use a special solution, gasoline or acetone. After processing, the product is dried again.

Pick up the load so that the shoes do not deform. A block in the shape of the letter L with an additional weight is optimal. Keep the product under pressure for at least ten hours.The adhesive is applied with a thickness of up to three mm, then it is kept for ten minutes and only then the parts are glued together. Choose only high-quality and proven glue. A suitable option would be the classic Moment glue, a product with polyurethane or an epoxy sealant. Alternatively, you can use special rubber shoe glue or shoe glue. Image - DIY repair of cracks in shoe soles

According to experts, polyurethane glue will be the best tool due to its strength and elasticity. It provides a secure fit and can repair any kind of shoe. In any case, these are toxic compounds, so ensure safe handling. If the product gets into the nose or eyes, immediately rinse the mucous membranes with running water.

Be careful when working, as the adhesive can spoil the material of the products, especially if these are suede boots, leather or patent leather shoes. The glue is difficult to wash off. Now let's figure out what to do if the soles of your shoes are cracking.

If the shoes are slightly loose at the edges, you can seal them up with a suitable glue. Clean and dry the products, degrease the surface so that the glue adheres better and provides a secure connection. Then you need to apply the composition to the parts and leave for ten minutes, then glue the boots and press down with a load.

To repair the crack in the sole, step back five centimeters from the gap in the direction of the heel and draw a parallel line. The area from the line to the nose is smoothed with sandpaper along with the crack. Then you need to glue the gap with Moment glue and make markings for the holes for the threads.

Remove the insoles from the shoes, take a boot knife and cut small holes along the markings. Then sew the material with strong threads through the resulting grooves. From above, each seam is covered with glue and left to dry. Clean and degrease the sole again, then cover with micropores and press down with a press.

Clean the crack inside and degrease. Cut the edges of the sole along the edges with a depth of one mm and indents of five mm in each direction. Then make a rubber patch with a margin.

A bicycle camera is suitable for making the patch. Sand the material and degrease, completely cover with glue on one side, on the other - leave dry edges of five mm.

Bend the cracked sole so that the break is revealed, and brush with glue. After it dries slightly, glue the rubber patch over the affected area and straighten it out. Leave under load.The listed methods will help if the soles of boots, boots or shoes are cracked.

You can seal the hole in the sole with silicone glue-sealant. You need to glue the products from the inside of the shoe under the insole. Carefully insert open glue into the hole and completely fill the hole with the compound.

Leave the products to dry under a press for the time specified in the instructions for the sealant. Close the big hole with a special polyurethane horseshoe and glue it with thick glue. You can buy such a horseshoe at the shoe department or store.

For spring and autumn, demi-season and winter shoes, a honeycomb or lattice sole design is often characteristic. If the sole burst on such products, as well as with prolonged wear, it gradually wears out. Voids form inside, the heel can fall through.

To restore such products, you must first remove the rubber that covers these honeycombs. To do this, tear off the insole, carefully clean each hole from dirt, debris, cardboard and glue residues. Then the empty honeycomb is filled with small pieces of micropores and filled with silicone sealant.

Reconditioning continues when the sealant has dried and hardened. Prepare new insoles, saturate with sealant or glue, glue to the sole of the shoe and press down with a load for the time specified in the instructions for the adhesive.

For summer shoes, sneakers, sneakers and other light footwear, you can buy a separate thin rubber sole and glue the products with rubber glue. This method is suitable if the products have flat soles. When gluing rubber to leather shoes, make a 45 degree hem first.

In order for the rubber to stick firmly and permanently to the polyurethane or nylon base of the shoe, first cut the template out of cotton fabric to size and weld it to the base using a hot iron. Then glue the new sole.

After repairs, it is important to look after the shoes and take care of the pair. Wash and dry items regularly. Which shoe cream is better to choose, see here.

If sneakers or sneakers have worn off at the location of the socks, sand the damaged area with sandpaper and degrease. Take different thicknesses of rubber or polyurethane and cut out the patch. A thicker material is applied to the site of damage, and a smaller one - to a normal sole.

Sand the patch in the place where it is adjacent to the damaged area. Then cover the material with glue and press it against the sole of the sneaker or sneaker. Keep under pressure for 24 hours.

If a hole has formed in the sole of a sneaker or sneaker, the edges of the hole must first be cleaned and degreased, then an adhesive should be applied. A fiberglass mesh (serpyanka) is inserted into a large hole.

Special glue is also used to fix a broken sole on figure skates. You can only help such shoes if the gap did not occur at the points of attachment of the blade. We examined how to glue the damaged shoe sole. And how to properly clean and wash sports shoes, read the link https://my.housecope.com/wp-content/uploads/ext/1653/garderob/kak-stirat-konversy/.

Video (click to play).