Do-it-yourself apartment renovation wall alignment

In detail: do-it-yourself repair in an apartment, alignment of walls from a real master for the site my.housecope.com.

Modern requirements for the renovation of premises have become much more stringent. Now, flat walls are an inapplicable attribute of an apartment or house. But the walls, even in new buildings, cannot be called that even approximately, and even more so in old houses. Therefore, for any, practically, repair, leveling the walls is an inevitable stage. How best to do it, about the methods and technologies, the possibilities to do it all with your own hands, and let's talk further.

Although technologies in construction are developing rapidly, wall alignment is still done in two ways: with plaster and plasterboard cladding. Another thing is that there are different compositions of plaster - based on gypsum and cement, and you can also mount the gypsum board in two ways: on the frame and on glue. But that's all.

Smooth walls - a requirement of our time

For some time, gypsum plasterboard sheets began to be replaced with gypsum fiber boards GVL). They consisted of a mixture of gypsum and plant fibers, but they turned out to withstand shock loads poorly and break even with minor impacts. Therefore, GVL alignment of walls with their use is now a rarity (sometimes they are put on the floor).

In Soviet times, the walls were leveled with plywood. But this is definitely the last century. Far from the best replacement for gypsum board, which in 100% of cases gives cracks at the joints, and even swells from moisture. So it turns out that there is nothing to use instead of drywall. So the choice is really not very wide.

Actually, there is one more way - putty. But it is used only on relatively flat walls with a difference of no more than 5 mm. Therefore, already leveled walls are usually putty, bringing the plane to the ideal.

Video (click to play).

If we talk about how easier it is to level the walls with your own hands, then many agree that it is easier to work with drywall. But it is not difficult to cope with plaster on the lighthouses. The main thing is to know the technology and not deviate from it.

The plaster is based on two binders: one based on cement and one based on gypsum. Gypsum dries faster, but the maximum layer to which they can be applied less is about 50 mm. Cement-based plasters can be applied in layers up to 10 cm, but they take longer to dry.

Lighthouse plaster is a reliable way to level walls

In addition to the thickness of the layer, when choosing the type of plaster mixture, it is necessary to take into account which of the finishes will come later, as well as the conditions of the premises in which you are going to level the walls. Gypsum is hygroscopic, therefore it is not used in wet rooms: the bathroom and kitchen must be plastered with a cement-based composition. The rooms and the hallway remain for the plaster. This is basically what they do.

In our description, we will use gypsum plaster - Rotband - a popular brand that has good reviews from both amateurs and professionals.

Removing everything that does not hold well on the wall: we beat it off, pick it out, clean it with a spatula. If there are cracks, we embroider them. Then we estimate the degree of curvature. If there are very large projections that stand out too much, it is advisable to remove them (with a hammer and chisel or a hammer drill).

First, we clean off everything that falls off

Often starting the alignment of walls in an old house, they decide whether to knock down the old plaster if it does not fall. In principle, the master should evaluate, but you can try it yourself. Tap the wall. If there are places that differ in sound - they sound more muffled - then the layer here has moved away from the main wall.If you "hang" another layer of plaster on it, there is a high probability that all this will collapse together. It will be much worse. So, it is better to whip up previously plastered walls down to the main material.

If during preparation there are separate too large potholes, it is better to seal them up separately. Putties have a minimum and maximum layer limitation. Too much layer may fall off. Therefore, it is better to pre-seal the pits or holes.

If the surface of the wall is too smooth, notches are made on it.

When leveling a concrete wall or a surface painted with a film-forming composition, another problem arises: it is too flat, which may cause poor adhesion to the plaster. This business can be helped by processing a primer such as "Betonokontakt", which leaves a rough film on the surface, improving adhesion.

Another way out is to make notches. Once they were made with an ax, now they use a hammer drill and a grinder more often. With their help, a notch is applied. According to the rate of notches per square meter, there should be about 100 pieces.

Depending on the type of plaster chosen (gypsum or cement), a primer is selected. Its main task is to improve the adhesion of the wall and plaster. Read the instructions for use of the primer carefully. Some require moistening the base before application, some require dusting, etc.

Priming the walls before plastering

There are two favorites in this group: Cerezit 117 and Betonokontakt. There are others, but these are used more often: good reviews. The composition may be ready-to-use or require dilution (concentrate). It is applied with a roller or brush, spray, or even a garden spray - to speed up the process.

Until this moment, there were no difficulties for self-aligning the walls. Everything is elementary. Further - a little more difficult, but also - not to build rockets.

If you want to achieve a flat surface, you can level the wall only along the lighthouses. These are such supporting elements that are exposed in the same plane. A layer of plaster is then leveled along them. As beacons, you can use special galvanized "T" -shaped beacons or flat wooden strips.

It is more convenient to use metal beacons - install faster. But the minimum layer of plaster is about 8-10 mm (6 mm of the lighthouse + mortar on which it is placed). The downside is their cost: although not very big money, but still additional costs. One more point: galvanized plaster does not “contact” well, therefore, after the initial drying, the beacons are removed from the wall, the holes are closed.

Read also: Samsung wf6520n7w DIY repair

Installed beacons for plastering on a brick wall

Using wooden planks is a cheaper option, but finding a sufficient number of perfectly flat bars in cheap material is problematic (you won't be using high-quality timber). Even if this succeeds, the probability remains that the tree will lead from the moisture. As a result, the wall will no longer be flat.

Some make lighthouses out of mortar. Stripes of plaster are pre-applied, leveling them into a level. After they have solidified, they are used as beacons. The cheapest way, but the most labor-consuming and much more time-consuming.

The alignment of the walls depends on how correctly the lighthouses are exposed. We set it up for sure - we got an excellent result. Wrong - you will suffer, correcting irregularities that you made with your own hands.

For details on how to install beacons to level the walls, read under the screed here.

The selected plaster is diluted as indicated on the package. Then they throw it on the wall. Use a wide trowel or paint bucket. They start from the bottom, cover with a solution a piece of the wall from one lighthouse to another.

Beginning of plastering the wall along the lighthouses

Then they take the rule, set it down below.Leaning on the lighthouses, pull up, slightly swaying from side to side. Several such passes are made until the solution is leveled. The composition that has adhered to the rule is removed with a spatula, again throwing it onto the wall.

Alignment of the putty on the lobes

Again - a portion of the mortar on the wall, leveled with a rule. So to the very top. Having tightened one strip, proceed to the other. So gradually align the entire wall.

The first stage of plastering is finished. But this is only the first. The surface is not ideal: if you look closely, there are small irregularities. They are leveled with a more liquid solution, achieving a smoother surface.

When the first layer has dried a little, but has not yet hardened (no later than 2-4 hours after application), leveling begins with a putty. The existing drawbacks are rubbed with the same solution, which was diluted a little thinner than required according to the instructions. Since it is more fluid, it is applied with a wide spatula, after stretching it along the wall with the rule, relying on not the same beacons.

Leveling walls for putty

So again they go through the entire wall, leveling it to a perfectly flat plane. This is necessary in order to reduce the consumption of expensive putty mixture.

When the solution has dried to a state of thick plasticine (press hard with your fingers, it bends), you can take out the beacons. They are pried at the bottom with a screwdriver and pulled out.

We take out the beacons from the plastered wall

They are removed very easily. Actually, because of the fact that they are taken out, that they form a heterogeneity in the plaster, which means that they reduce its strength.

Now we take the rule, clean it of the adhered solution and, stretching it in different directions, finally level the surface. This should be done at the initial stage of thickening, when gypsum plaster looks like plasticine: it is easy to cut it off with the rule.

Carrying out the rule in different planes, we finally align the wall

When the surface was leveled, diluted by Rotband. They are closed immediately, without waiting for something: until the plaster has finally hardened, new layers stick to it well.

The solution is applied and removed with a spatula. At the same time, make sure that the surface remains flat. At this, the alignment of the wall under the putty can be considered complete.

When leveling walls with plaster in apartments, the angle in which the heating pipe runs becomes a problem. You can't crawl there with a rule, but a spatula just doesn't work. If you are familiar with such a problem, watch the following video.

How to level the walls with your own hands

When it comes to plaster, there are many types of plaster on sale. The composition is different and it can be made of plaster or cement, but when installing drywall on the walls, glue is used for installation, a frame made of wooden slats or a metal profile.

Some people use gypsum fiber sheets (GVL) for walls instead of drywall. They contain gypsum material and plant fibers, but such material does not withstand impacts and other loads poorly, damage can appear even with light impacts. All this has led to the fact that GVL is rarely used. In some cases, drywall is replaced with OSB-plates, and previously plywood was used. True, such materials are not the best alternative to gypsum board, which over time begins to crack along the plane, can swell. Chipboard is also used for uneven walls or floors, but the material is several times more expensive than drywall. Therefore, today it is best to use drywall for leveling.

Advice! Plaster, putty can also be applied. This option should be chosen only with the relative evenness of the walls, which have small differences, up to 5 mm. In this regard, even walls can be putty in order to get an ideal surface.

Many craftsmen say that it is better to use drywall for independent work. It is easier and more convenient to work with it, the design of the walls is cheap. But if you use the alignment of the wall along the lighthouses, then the work is also not difficult, a novice builder can do it, the main thing is to figure out the technology and not rush into the repair process.

Concrete walls or walls made of bricks and other materials must be prepared before leveling. It makes no difference which type is chosen. Preparation consists in the following sequence:

Based on the choice of fillers, a primer is selected. The main purpose of the primer is to improve the adhesion of the plaster to the wall. The instructions on the packaging will allow you to make the right choice, as well as familiarize a person with the correct application to the walls. Often the compositions are ready-made, but there are also those that need to be diluted. You can apply the primer to the walls with a roller or other device. The preparation is simple, but the alignment workflow will be more complicated.

To make a flat surface from a curved wall, beacons are used to level the walls. This is a profile that is exposed in one plane on the wall, the beacon will guide the plaster to the right places, filling in the voids and achieving the evenness of the walls. The beacon method involves the use of a galvanized steel profile, these are T-shaped profiles, although a bar is also used as guides.

The metal beacon is more convenient to use than the lumber method, it is easier and more convenient to mount it. The plaster layer will be about 8 mm. The disadvantage of the method lies in the cost, the amount is not large, but these are additional expenses. In addition, plaster and steel do not adhere well to each other, so when the mixture dries, the beacons are removed and the holes are repaired.

When using wooden slats, the process becomes cheaper, but even timber is more difficult to find. The wood is driven away from moisture, and the plaster layer is uneven. Some people use the solution as beacons. Initially, strips of plaster are applied to the wall, leveled under the level, and after drying they are used as beacons. The method is cheap, but also more complicated than other types of beacons.

Important! The evenness of the walls depends on the correct installation of beacons. If you put the beacons evenly, then the result will be excellent, if there is an error, then the required result will not be the best and you may need to redo the work.

For installation on the wall, several plaster cakes are made, a profile or bar is embedded in them, everything is set at the level to the desired degree, you can use a plumb line. When the cakes are dry, you can continue to work. The width between the beacons is taken from the calculation of the rule that is available.

The plaster is prepared according to the instructions on the package, after which it is applied to the wall. In the work, you will need a spatula or a bucket for painting. After sketching, the order of work is as follows:

You need to start throwing the solution between the beacons from the bottom point, covering part of the wall.
The rule is placed on the beacons at the lowest point, resting on them, the plaster stretches up. You need to lay the mixture with light swaying of the rule on the sides.
It is necessary to putty until the laying of the mortar is solid and even.
The adhered mixture is removed with a spatula and again thrown onto the concrete, wall.
The work is carried out to the top. After one strip of lighthouses, you need to lay the next one, and so on every square meter until the room is with even walls.

This completes the first part of the work. The starting layer has been laid, but the walls still need to be leveled, even visually the unevenness is noticeable. Fully leveling the wall will turn out to be a more liquid composition.

If the first layer began to dry out, but did not have time to harden, then it is time to level the wall under the putty. All defects are overwritten with a solution, according to the consistency, it is necessary to use a thinner mixture. The application is done with a large spatula and is leveled according to the rule of the beacons. Thus, the entire perimeter is traversed, it is better to make a thin layer and the base turns out to be close to ideal. This stage is necessary so that the consumption of the putty is minimal.

If the solution is like thick plasticine, the beacons are taken out by prying them with a screwdriver at the bottom. Further, the seam is filled with putty and the wall is leveled with a spatula, if necessary, the seam can be cut, because in the state of incomplete solidification of the mixture, it is perfectly cut.

Important! During alignment, care must be taken so that the plane remains flat.This completes the alignment of the walls. Further, it is possible to carry out interior finishing work, painting the walls in different colors, gluing wallpaper on them, laying tiles and other finishing materials.

Various dry mixes are used for finishing. They all have different compositions and have different characteristics. For leveling the surface, dry material is most often used, which is presented in the table:Very few apartments can boast perfectly flat walls - in most cases they have depressions and other defects, or even significant vertical deviations. It is difficult to stick wallpaper on such walls, it is almost impossible to decorate them with decorative stone or tiles, and even ordinary painting will not look very aesthetically pleasing. On uneven walls, the finish will quickly lose its original appearance, and you will have to start repairing it again. To save time and money, it is better to level the walls right away. What is the best way to level the walls and how to carry out all the work?All wall alignment methods are divided into two fundamentally different groups.:

Image - Do-it-yourself apartment renovation wall alignment

the use of mixtures (plaster and putty);

dry leveling (drywall is more often used).

One way or another choose, taking into account the degree of unevenness of the walls, therefore, this stage is especially important. How uneven the walls are can be measured laser level or ordinary building level.

The simplest and very popular way is use of plumb lines... First of all, a nail is driven into one of the upper corners of the wall, and so that 2-3 cm remains on its surface. A plumb line can be made from a long thread and a nut or other load. The finished plumb line is tied to a hammered nail, the weight should almost reach the floor. When the thread with the load stops wobbling (i.e. the plumb line forms a strictly vertical line), you can drive in a second nail at the bottom of the wall so that the thread and the head of the nail are at the same level. The same procedure is done on the opposite side of the wall. Four nails are connected with a cord and form a strictly vertical plane, which allows us to understand the degree of deviation of the wall level from it.

We evaluate the irregularities and choose the alignment method:

depressions and irregularities up to 0.5-1 cm can be leveled with putty;
drops of up to 3-5 cm are best leveled with plaster mixtures;
drops of more than 5 cm are easier to align with gypsum cardboard sheets mounted on a specially constructed frame.

To level the walls, use gypsum and cement plasters... Gypsum compositions allow you to achieve an optimal microclimate in a room, but they are afraid of water, therefore they are suitable for bedrooms, living rooms and children's rooms. Cement plasters can be safely used for leveling walls in rooms where humidity will constantly increase.

Sequence of work looks like this:

The main advantage of this leveling method is the maximum preservation of the usable area of the room. The disadvantages are the laboriousness of the process, the need to prepare the base and the presence of a large amount of dust.

The putty is suitable for finishing walls or for those surfaces where there are slight differences in height, potholes and other irregularities. The puttying process is simple, and quite doable with your own hands. The sequence of actions is as follows:

When it comes to the largest irregularities and significant differences in the level of the walls, the best way to level the surface is to use drywall, and mount it in a frame manner. In this case, this is the most a simple, cheap and quick way to get a perfectly flat and smooth wall surface... In addition, you do not need to spend a lot of time and effort on preparing the surface of the wall - it, with all its cracks, potholes and drops, will be hidden behind the frame and drywall.Moreover, inside the frame, you can lay some communications or equip additional heat and sound insulation.

However, do not forget that this way of leveling the walls will take up a lot of usable area, and if it is already in short supply, then the room runs the risk of turning into a hole. Walls sheathed with drywall sheets will be able to withstand less stress than those that were leveled with plaster. If we are talking about a room with high humidity, then you should use moisture-resistant drywall sheets.

Sequence of work:

A similar technology is used to produce leveling with plywood or plastic panels, constructing a frame from wooden blocks... Often, the walls in country houses are aligned in this way.

As you might guess, in this case there is no need to construct a frame from a profile, which greatly simplifies and speeds up the process. In a similar way, both minor irregularities and differences in the level of up to 2-5 cm can be leveled.

Sequence of work:

Smooth walls are a guarantee that the finishing materials will look the way they should and will last as long as possible. Let the process of leveling the walls be quite laborious, it should be taken with the utmost responsibility, so that henceforth only cosmetic repairs can be done, refreshing the atmosphere in the apartment.

Good afternoon, dear readers of the leading construction portal Quite recently, I learned that on this site you can publish your renovation history and decided to share - my technology for leveling the walls in the apartment. I will say right away that leveling the walls is a rather complicated process and not every owner can do it, but if you are determined, then you will succeed, so let's start.

How to align walls in an apartment

The walls are aligned for many reasons, of course initially - this is an aesthetic component. The appearance of your apartment entirely depends on the geometry of your walls and the smoother they are, the more expensive and sophisticated your apartment looks. The leveled walls with putty, and not covered with plasterboard, give particular value, because the latter visually reduces the space of the apartment, and also creates inconvenience associated with its operational properties (it is difficult to hang pictures, mirrors, etc. on drywall).

In addition, the owners of apartments with broken wall geometry (this is especially common in the so-called "Khrushchev") suffer from wavy baseboards (both ceiling and floor), which repeat the contour of the wall and violate the visual geometry in your apartment. If you are faced with a similar situation, then wall alignment is an excellent solution for you.

Spatula and basin for leveling the wall

Gypsum plaster Volma layer for leveling walls

Ceresite primer CT 17 winter

So, the materials and tools are ready, it's time to start leveling. Initially, we prepare the walls, tear off the old wallpaper and clean the surface. In order to free the surface of the wall from old wallpaper, it is imperative to moisten the wallpaper with water using a spray (which is sprayed on flowers), thanks to this it will be easier to remove the old wallpaper.

Tearing the old wallpaper off the walls

We lay the wiring under the outlet in the wall

Priming the walls with a brush or roller

Is the priming of the walls complete? now we proceed to sealing the seams. In order to seal the walls as well as possible, it is necessary to add PVA glue to the solution, and then mix the solution using a drill with a special nozzle. You can see the process of mixing the solution in the video below.

Next comes the next stage - this is the application of a rough layer. The rough layer is applied using plaster, which sometimes should be mixed with PVA construction glue, for stronger adhesion to the wall surface.

Plastering is not done spontaneously; ideally, you need to install special construction beacons, adjusted using a building level and then, based on this, apply plaster to the wall using a building rule, but this is a very costly method in terms of plaster consumption. It is easier to use the building level and mark the gaps with a pencil in the differences, and then apply plaster to these places. The process of leveling a wall without beacons will be shown in the video below.

Wall rubbed with a rough layer of plaster - photo

Many renovations start with the problem of crooked walls. Let's try to figure out how to efficiently level the walls with our own hands without the involvement of specialists. Let's take a look at four of the most popular and effective ways to achieve nearly perfectly flat walls.

You can quickly and efficiently level the walls using drywall sheets. They are easy to cut, strong enough, and even a little construction skill is enough to get the job done successfully.With the help of drywall, you can correct wall defects of almost any complexity: close minor irregularities and significant differences in the surface. And besides this, such a building material as drywall makes it possible to arrange niches and portals in the walls, arrange doorways in the form of arches, and even erect new partitions.Depending on the degree of curvature of the walls, the leveling method is also used, using a frame base or fixing the sheets directly to the wall. Sometimes there are cases when the walls in the same room have different degrees of curvature, and then it is more expedient to combine both methods. Image - Do-it-yourself apartment renovation wall alignment

Fastening drywall sheets to the frame

Before leveling the walls with plasterboard, it is necessary to carefully remove the old coating, be it crumbling plaster or multiple layers of old wallpaper. And don't be fooled by the fact that the surface will eventually close anyway. By cleaning the wall, you not only get rid of the accumulated rubbish in this way, but also reclaim precious centimeters of living space. Further, it is recommended to treat the surface with an antiseptic, which will destroy possible fungal deposits, including the most dangerous black mold.

Now you can start attaching the base. As a frame, a profile made of galvanized steel is most often used. First of all, using dowels or self-tapping screws, profiles are fixed along the perimeter of the wall - along the ceiling, floor and adjacent walls. Further, vertical jumpers are installed on this frame, which will become the basis for drywall sheets. During installation work, it is important, using the building level, to often check the correct installation of each profile separately. The profiles are connected to each other with special screws ending in a small drill, which allows them to easily enter the metal sheet and reliably bind the structural parts. When the frame is ready, you can start sewing it with drywall sheets. This stage of work is performed much faster than the previous one, and the main thing here is only to perform the correct joining of the sheets so that the edges are securely fixed and form a single plane.

In addition, it is necessary to strictly observe the verticality of the lines in the corners of the room, where even the slightest deviations will be noticeable.

When all the sheets are already screwed on, their joints must be putty with the obligatory use of a reinforcing mesh. Further, after the putty has dried, it is recommended to apply a thin layer of plaster on the wall, which will become a solid base for painting, wallpapering or laying tiles.

If the curvature of the walls is insignificant, you can save on the frame and level the walls with plasterboard, fixing them directly to the wall. After qualitatively carried out preparatory work, they begin to glue drywall sheets to the wall using a special composition, the application layer of which depends on the differences in the relief of the walls. In the most problematic places, drywall is additionally fixed with long dowels or self-tapping screws.

At the same time, do not forget about the building level - after all, you are trying to achieve a perfectly flat and strictly vertical surface. Further plastering, plastering and priming of finished walls is not canceled in this case.

A cheaper option for repair work is leveling the walls with plaster. In this case, the cost of acquiring materials is reduced, but a little more skill and time will be required.

In addition, responsible preliminary preparation will be a guarantee of tight adhesion of the applied plaster layer. And this work consists in the complete removal of the old coating right down to the very base of the walls, that is, up to brickwork or concrete. And even if the old plaster seems to you still quite strong and durable, it is better not to risk it, because its possible delamination in the future will nullify all your efforts and expenses.

Plastering walls is a rather laborious and technologically complex process, especially if you have little experience in this matter. You need to be prepared for the fact that not everything will go smoothly right away (both literally and figuratively), but some practice and applied diligence contribute to achieving the maximum possible result, because "it is not the gods who burn the pots."

The best plastering result is obtained by aligning the walls with beacons, which not only help to control the uniformity of the plastering solution, but facilitate its distribution. Perforated T-shaped rolled metal products are used as beacons. They are fixed vertically on the wall at a certain distance, usually not exceeding one and a half to two meters. Only experienced plasterers can afford to save on the number of pendulums, but for beginners, pendulums will become real "helpers". And we should not forget about the building level, controlling the verticality of the fixed beacons.

Next, you need to apply a primer to the walls and let it dry, thereby improving the adhesion of materials when applying the solution. Depending on the condition of the wall and the degree of its curvature, the thickness of the applied layer is determined. And if it is more than 2 centimeters, be sure to use a reinforcing mesh.

gypsum plaster mix;
container for solution preparation;
construction mixer for mixing plaster;
craftsmen and spatulas.

The technology for applying the solution to the wall is simple. A certain amount of the mixture collected on the trowel is thrown into the wall between two adjacent pendulums with sharp movements. After filling the space, using a flat plank called a falcon, moving along the pendulums from the bottom up, the solution is evenly distributed. This stage of work requires some effort. The mortar from the board is collected with a trowel and again pounced on the wall, filling in the recesses and recesses.

Thus, all walls of the room are plastered to the most even surface.

The next step will be grouting and sanding the walls.Usually, such work to eliminate defects begins as soon as the solution dries up, and this may take from several hours to a day, depending on the thickness of the applied layer. For mashing, use a special metal mesh or ordinary sandpaper. The process is, of course, laborious, but without it, it is almost impossible to get even smooth walls. Further, the walls are primed and are already completely ready for applying the finishing material. In the case when such flaws remain in the work as cracks, small grooves or surface drops, they can be easily eliminated with putty work.

This method is perhaps the simplest and most inexpensive in deciding how to level the walls with your own hands. Minimal material consumption and great effort will prepare the walls of your room for painting or wallpapering.

There are two types of putty - starting (with a larger texture) and finishing (plastic and homogeneous). The first is used to seal holes and cracks more than two centimeters deep, and the second is used to create a perfectly flat surface.

Putty work, like all previous ones, begins with preparatory cleaning of the surface and the obligatory application of a primer.

Advice! In this case, a primer is not recommended, but mandatory, since dust and small particles of debris will prevent the solution from sticking to the surface, and when applying the finishing compound, they will cause scratches on a flat surface.

The putty of irregularities and individual recesses in the wall is performed with a small trowel, with smooth, pressing movements. After the solution has dried, the applied "patches" are sanded with sandpaper, trying to level the surface as much as possible. If the wall is being prepared for painting, then the next step will be processing with a starting putty. It is more convenient to apply it using a broad building rule, since the mortar will be more evenly distributed and the work will go much faster than using a spatula.

Another option for using the finishing putty is the creation of decorative, textured plaster. But it should be remembered that such finishing works are performed only on perfectly aligned walls.

The building material market is replete with assortments of wall panels, with which you can not only correct the curvature of the walls, but also use them as finishing materials. One has only to get acquainted with the proposed panel options and the question of how to properly align the walls becomes resolved.So, a variety of types allows you to purchase panels for any style of interior: solid wood, MDF, PVC, plastic, chipboard, laminated, veneered, embossed and smooth. As for the colors, here too the choice is rich from natural natural shades of natural wood and "marble", "brick" or "stone" masonry, as well as with fabric ornaments or embossing "under the skin". Image - Do-it-yourself apartment renovation wall alignment

Video (click to play).

Panel mounting technology is similar to drywall fixing technology. Whether it is necessary to install a metal frame or fix the sheets directly to the wall depends on the degree of differences and curvatures. In many interiors, whether a part of the wall is trimmed with panels, for example, in corridors, hallways or living rooms. But in the kitchen, only the wall behind the work surfaces can be covered with panels.