DIY bathroom repair with plastic panels in Khrushchev

In detail: do-it-yourself bathroom repair with plastic panels in Khrushchev from a real master for the site my.housecope.com.

Do-it-yourself bathroom repair in Khrushchev is one of the most difficult tasks in all apartment renovation.

Despite the seeming simplicity - after all, in fact, no special delicacies are often required - the whole task is complicated by the small area of the bathroom. At the same time, difficulties are aggravated by the fact that most often repair work has to be carried out in a room that is far from ideal condition. Therefore, the lion's share of efforts is spent not on the repair itself, but on preparing for it and bringing communications "into a divine form."

However, you should never give up. With proper preparation, even from a cramped, typical "Khrushchev" bathroom or a combined bathroom, you can make a modern, practical, functional and beautiful room.

This means that the better we prepare, the better the final result will be!

Small bathroom interior

What should you pay attention to first of all when planning the renovation of bathrooms in Khrushchev?

The first and most important factor is the small floor space.

This is very important for us because:

Firstly, we will have to be very careful about the arrangement of the main details of the bathroom interior, because the classic bathroom layout in Khrushchev is far from ideal.
Secondly, in a room with a small area it is better to use finishing methods that “steal” space as little as possible.

So, from the point of view of gain in area, you can abandon the wall cladding with plastic panels in favor of tiles.

In addition, when planning repairs in the Khrushchev bathroom, it is necessary to take into account the location of communications and their condition.

Video (click to play).

This is especially important for the Khrushchev houses, because often in them you can find pipelines in an extremely deplorable state, but at the same time it is not possible to move them.

The most rigidly "tied" the entire bathroom to the sewer riser, because it is impossible to change its position in principle.

Therefore, a complete redevelopment of the bathroom in the Khrushchev is significantly difficult - keep this in mind.

Bathroom during redevelopment

But if you have taken into account all these factors and planned the location of interior items, you can start repair work.

However, when starting to repair a bathroom in Khrushchev, we can often face a situation where the volume of preparatory work significantly exceeds the volume of the repair work itself - both in terms of time and financial costs.

Renovation of a bathroom in Stalinka in this regard is not too different - before the renovation itself, large-scale preparation will also be required there.

Before starting to prepare for the renovation of a small bathroom, we need to evaluate the following parameters:

Are there any plans to redevelop the bathroom in Khrushchev?
What is the condition of the bathroom?
Has the integrity of the floor (screed and waterproofing) been compromised?
Is wall alignment required?
Is it possible to operate the installed pipelines, or is it necessary to replace them?

As soon as the assessment is completed, we draw up a work plan and start preparing the bathroom for repair.

Below is a complete alteration of the bathroom in Khrushchev - with the expectation that a major overhaul of the bathroom is planned.

In the event that you are not planning a complete redesign, you can only use the recommendations that are appropriate for your situation.

We carry out the work according to the following scheme (for more details, see the video attached to the article):

Using a perforator, we remove the remnants of the finish and the old screed from the floor - to the concrete base. We clean the base with a brush, remove dust and lay waterproofing materials with the obligatory approach to the walls up to 15 cm.

Pour a concrete screed over the laid waterproofing.

We start replacing pipelines with replacing risers - this stage is the most time consuming. All pipes are either laid in grooves punched in the wall, or we are securely fixed to the walls with clamps.

As an alternative method of leveling, you can consider wall cladding with cement-based slabs or moisture resistant plasterboard.

Particular attention should be paid to leveling the walls when repairing a bathroom in stalinka - on high walls, any unevenness becomes very noticeable.

When wall cladding with plastic wall panels, alignment is not required.

However, in this case, as well as when leveling the walls with drywall or cement slab, the walls must be treated with an antifungal composition.

After the preparatory work is completed, the communications are in order and the walls are leveled, you can start finishing work.

The main bathroom lined with plastic are as follows:

Coloring. Painting the walls of the bathroom is one of the most economical finishing options, so if your budget is limited, you can safely stop at this option.

It should be borne in mind that the walls for painting are putty very carefully - after all, it is much easier to hide irregularities under the tiles, and even more so under the wall panels.

For painting the walls in the bathroom, it is better to use a specially designed paint for this - this way the result will be much more presentable.

Still, paint is primarily a way to save money, so it's best to consider other finishes.
Finishing the bathroom in Khrushchev with wall panels. Today, bathroom wall cladding with the so-called "plastic clapboard" is quite popular.

At the same time, the choice of wall panels for the bathroom is very wide, so you can pick up not only smooth white panels, but also really high-quality mass-dyed panels with a texture imitating fabric, wood or stone.

Plastic panels are mounted on a special lathing made of a metal profile or a wooden bar, while the lathing itself is securely attached to the bathroom walls using dowels.

To fix the panels on the crate, we use either "liquid nails" or a construction stapler.

Finishing a bathroom in Khrushchev with plastic panels involves fixing several boards under the cladding.

It will be possible to subsequently attach wall cabinets and shelves to these boards, without which no bathroom can do.

Facing with tiles. Tiles are one of the best options for decorating a bathroom not only in Khrushchev, but also in any other apartment - both from the point of view of appearance and from the point of view of practicality and durability.

For tiling the bathroom walls, we align, and then we apply vertical and horizontal marking lines on them. We will navigate along these lines when laying the tiles.

For laying the tiles, we use special glue, which we wear on the wall with a notched float. Fill the seams between the laid tiles with a special compound - the so-called grout.

Bathroom flooring offers us significantly fewer options. For economical repairs in Khrushchev, linoleum is also suitable as a bathroom flooring, but the appearance of such a coating leaves much to be desired, it is better to consider the design of the tiles in the bathroom.

It is still worthwhile to dwell on the floor cladding with special tiles.

Bathroom floor tiles differ in structure from wall tiles - they can withstand higher loads and have a higher coefficient of friction.

And this means that it is impossible to use wall tiles (even if surpluses have formed after the wall cladding).

The most detailed description of the repair in the bathroom in Khrushchev is the video instruction that you will find in this article. However, the algorithm itself, which describes the sequence of actions, will help you plan the repair and make it as effective as possible!

The use of PVC panels for finishing the bathroom is a method that is gaining more and more popularity. Made of plastic, they are great for humid environments. Manufacturers offer a wide range of different colors and patterns. They produce options for both walls and ceilings.

The biggest advantages are durability, ease of installation, replacement, operation. The disadvantages include low strength. The panels break quite easily from strong pressure or impact. Today it is the cheapest finishing method.

In addition, people who have just recently moved into a new house should think about such a renovation. For the first few years, the house will shrink. The covering with tiles may not withstand, give cracks, but nothing will be cheap, perhaps temporary, finishing with plastic.

If the choice still fell on the renovation of the bathroom with PVC panels, then you can invite specialists. They will do everything on a turnkey basis. Starting cost from 15,000 rubles.

Image - DIY bathroom renovation with plastic panels in Khrushchev

But you can install the panels yourself. Packing price (10 pieces) from 100 rubles. It's simple. I suggest following the instructions.

Step 1: Calculation, material selection.

Measurements. Be vigilant and attentive so that later you will not feel sorry for the effort and money spent. Determine where and what will be in the bathroom, calculate the correct amount of material required.
Panel selection. For the bathroom, specimens with a matte or glossy surface, with or without a pattern, are suitable for a bathroom, width from 10 to 30 cm, length from 2.5 to 6 meters, thickness from 0.8 to 1.2 cm.

Approximate color options:

They also produce versions with a mirror surface, but they are not suitable for a damp room.

Step 2: Preparing for installation.

Dismantling the old coating
Choice of installation method. There are three mounting options:
Fastening to the wall with glue, liquid nails. Suitable only if the walls of the room are already prepared, perfectly aligned. The method beckons with its simplicity, but after a while difficulties may arise when you decide to replace the coating. It will be very difficult to detach them from the wall using special brackets. This method requires flat walls. In addition, the brackets are attached directly to the wall with nails or self-tapping screws, and if it is concrete, you will have to use "chopiks" for each hole. This option saves space, since the panels are attached directly to the wall, without additional fixtures.
Installation using guides, battens, which can be made of wooden beams, slats, plastic, metal. Fast, reliable way. Does not require wall alignment. I propose to consider it in more detail.
Selection of the necessary tools. For fastening with guides you will need: a wooden bar or slats, nails, screws, a hammer, a drill. Instead of a timber, you can use a mounting profile with fastening brackets.

Step 3: Installation.

Using a level, guides are horizontally attached to the wall. Three, attached to the wall near the ceiling, near the floor and in the middle, may suffice. But you can strengthen the structure by placing the guides at a distance of 40 to 50 cm from each other.
We begin to mount the panels from the corner farthest from the entrance.They can be attached to the guides with self-tapping screws, staples at the joint, which will then be hidden. The panels are connected tightly to each other with a lock, which is already provided in their design.
Rice. Fastening panels to rails
Rice. Fastening panels to rails using special brackets
Rice. We fasten the panel to the metal guide using a self-tapping screw
Corners, joints are neatly masked with the help of special edging, corners. There are several types of profiles, moldings, which will make the finish with plastic panels completely complete. They are used at the joints of panels with each other in the corners, in the area of the ceiling, doors.

These areas must be protected from unwanted moisture ingress by coating with sealant. Particular attention should be paid to the junction with the bathroom. Before applying the sealant, it is necessary to give a load, that is, fill the bathroom with water. Due to this, the contact of the product with the surface will be of better quality, no cracks will form during the use of the bathroom.

So, as you can see, the process is really not complicated, fast, and does not require any special skill. In a short time, without large material costs, you can enjoy your renovated bathroom.

Bathroom renovation can be called the most expensive. Indeed, it is for this room that it is necessary to choose materials that can withstand all the negative effects of high humidity. After buying an apartment, even a relatively inexpensive one, you don't want to spend extra money on putting it in order. Having studied the specifics of the work and stocked up with the necessary materials, you can start finishing on your own. Regardless of whether you want to carry out a budgetary repair of a bathroom in a Khrushchev with your own hands or in a large country cottage, the main thing is patience.

Renovation in the bathroom, as in any other room, requires certain materials. Therefore, initially you need to make a list of what you will need in the process of work.

Repair materials and their selection:

Ceramic tile . For small rooms, it is worth buying a small tile, about 20 * 30 cm.Preference should be given to light and warm shades.
Tile adhesive. It is not worth saving on this item, it is better to choose a quality product from a well-known manufacturer.
Panels. This type of finishing material should be chosen solely according to your preferences. Repairing with PVC panels is a good way to make work easier.
Plaster mortar. This material will be needed to level the walls. The best option would be to choose a ready-made plaster composition.
Moisture resistant drywall. It is suitable if you do not want to level the surface from scratch with cement compounds.
Putty - needed to patch up small damage on the surface.
Primer. An indispensable tool for preparing the base.
Oil or acrylic paint. If you are planning to paint your bathroom, purchase a moisture resistant brand of paint composition.
Grout. It should match the tone of your tile and stand out a little. It is also better not to save on this composition.

If you are doing your own bathroom renovation, the plastic cladding will be much easier to make than laying out the tiles. The lining can be attached to the walls with tile glue or liquid nails. If your goal is not to save space, then you can use a frame.

Attention. Poor quality plastic can contain harmful substances, so people prone to allergies should use this material with caution.

Plastic is also an excellent option for ceiling decoration. A variety of color schemes for construction lining will allow you to choose an extraordinary option for your room. As a frame, you can use wooden blocks and metal profiles. They are attached to the ceiling with screws.

It is believed that it is very economical to make repairs in the bathroom with plastic panels. Since this material is several times cheaper than a ceramic coating.

Absolutely any repair requires preparatory work, which will not only allow you to carry out all the work efficiently and economically, but also preserve your property and health.

Vacation of the premises. All hanging elements (mirrors, shelves, etc.), plumbing fixtures (if they can be dismantled), mixers and lamps must be taken to another room. If this is not possible, then some items can simply be covered with polyethylene, so as not to damage or stain them.
Clearing and dismantling of old finishes. Tiles, paint and other cladding materials must be removed. It is imperative to wash off the old whitewash from the ceiling. The adhesive from the tiles must be completely washed off.

Important. It is better to carry out preparatory work with the help of power tools, since it is troublesome and time-consuming to do it manually.

Even cheap bathroom and toilet renovation includes the obligatory preparation of surfaces. To do this, you will need:

Level the walls with plaster or drywall. If the wall was covered with oil paint, then it must be knocked down, since the plaster on such a surface will not last long.
Treat the surface with a primer. It can have various properties - strengthening, bioprotective, hydrophobic, increasing adhesion, and so on. It is worth choosing it based on where it will be used - in a private house made of wood or in a typical dwelling.

Read also: DIY vaz 2110 optics repair

After carrying out the preparatory work, you can proceed to decorating the walls, ceiling and floor. It is better to perform all actions in this sequence.

When repairing the bathroom floor, pay attention to the presence of waterproofing. It must be in the bathroom. This will keep you out of trouble with downstairs neighbors who may have dark spots on the ceiling from exposure to water. The best material for waterproofing is "aquaizol" and its analogues. Laying is carried out "overlapping", and the joints of the material are glued with bitumen mastic. The use of insulation in a panel house is especially important.

Since the bathroom floor can sometimes be humid, it is worth choosing tiles with a textured, rough surface. This will protect you from slipping and accidental injury. The tile is usually chosen very large, although there are no restrictions on its choice.

In addition to tiles in the bathroom, you can also use baseless linoleum. It will not rot from moisture, especially if it is glued correctly and will cost you very little.

Before starting work, you should make sure the surface is even. It is not necessary to make it perfectly smooth, as scratches and cavities will not interfere with the gluing of the tiles.

Kneading the glue. It is better to do this with a drill with a special attachment.
Applying adhesive to walls or floors. It is necessary to carry out these works using a comb spatula with a tooth of 5-6 mm.
Tile bonding is the most difficult part of the renovation technology. To complete this operation, you must attach the tile to the surface and press down. It is advisable to use a rubber mallet as an aid.
To make the seams the same, you need to insert plastic crosses-separators between the tiles. They can be removed the next day.
Grouting. When repairing a bathroom combined with a toilet, you should carefully consider the choice of a trowel. A good mixture will protect the joints from moisture penetration under the tiles and will not become a habitat for various fungi. Seams can be repaired after at least two days.

A truly good repair can be called a work during which it will be possible to hide all engineering networks.After all, the marking of communications and their factory colors will not add beauty and comfort to any room.

Some methods will help to eliminate such a nuisance. For example, non-volumetric pipes can be hidden under a tile, having previously hollowed out a groove in the wall. For sewer pipes, you can make a box from OSB or drywall. Subsequently, the box is also tiled.

If you are carrying out purely cosmetic repairs to the ceiling, painting or whitening it, then getting rid of the kind of pipes near the ceiling will be very problematic.

We make the correct grooves and hide the pipes:

With a grinder, we make two parallel slits of the required depth and knock out the area between them;
The depth and width of the groove is best determined visually using a piece of pipe;
After the pipe is hidden in the groove, it must be fixed with a plastic clamp;
It makes no sense to cover the seams with plaster, because the tile covering will perfectly cover them.

Hiding communication elements will be especially useful for those who are renovating a small bathroom, as it will help to save extra centimeters of free space.

Advice. The dust generated by the grinder can harm your health. Therefore, be sure to use protective equipment - mask, glasses, gloves, and so on. If this is not possible, then try to properly humidify the room. If the grinder is clogged with dust, then a gauze filter can be attached to the engine grill. This can be done using ordinary tape.

The very last thing to do in the bathroom is to clean up and install all plumbing fixtures and accessories.Having studied the recommendations for step-by-step repair of a bathroom in a wooden house, in a Khrushchev, in a new building or in a luxury apartment, you can easily refresh not only your home, but also the living space of your relatives and friends. Why spend money when you can do all the work yourself.Renovation of a bathroom, in the traditional sense, comes down to wall cladding with ceramic tiles. It is perfect for these purposes due to its properties: practicality, reliability, attractiveness, ease of maintenance, hygiene, resistance to moisture and sudden changes in temperature. However, ceramic tiles have disadvantages. The high price, the complexity of self-cladding repels people who decide to make economical repairs in the bathroom from it. The decoration of the bathroom with plastic panels is now gaining great popularity, because this finishing material is in no way inferior to the usual tiles, but even has advantages - budget cost, ease of installation, good sound insulation. They can successfully revet the walls with their own hands.PVC panels are rectangular, hollow surfaces, finished with plastic, have perforations on the inside. On the front side there is a decorative pattern that imitates natural material (marble, wood), a 3D image that is currently fashionable, photo printing or a simple colored background. PVC panels have standard sizes: width 10, 12.5, 20, 25 cm, length 6 meters. Unfortunately, wall panels have important disadvantages:

pliability to mechanical damage, fragility;

poor resistance to fire;

"Eating up" when installing useful space in the room, so they can be chosen for a spacious bathroom in Khrushchev.

Having decided to cover a bathroom or toilet with moisture-resistant panels with his own hands, the owner faces the choice of a suitable finishing material. The assortment of PVC panels for the bathroom is very rich. The main selection criteria are as follows:

color - for small-sized bathrooms and toilets, it is recommended to choose light colors (pink, turquoise, pastel) panels. Visually, they will make the room more spacious. This is especially true in the "Khrushchev";

drawing - small images located across the canvas also help to create a feeling of large dimensions of the bathroom and toilet. For rooms with low ceilings, stripes or other elongated objects depicted on the walls increase the volume of the bathroom;

strength - stiffening ribs make the panel durable. The more there are, the stronger the materials;

relief - too large protrusions, roughness make it difficult to sanitize the walls;

composition - the mandatory presence of hydrogen, carbon, chlorine in the PVC panels. The presence of ethylene is not more than 43%, combined chlorine is not more than 57%;

smoothness - the material with irregularities after installation will have slots into which water and dirt are clogged. This leads to the appearance of mold, mildew.

The use of moisture-resistant slabs in Khrushchev, "small-family" and other small apartments is especially important. The combined bathroom gives some gain in the struggle for space. A well-chosen cladding design will visually enlarge the room. It is pointless to make expensive repairs in Khrushchev, since these houses are planned for demolition. Therefore, the economical option using do-it-yourself PVC plates is the most attractive. The panels will successfully hide the flaws of the walls and plumbing, hide the inelegant pipes.

Any self-respecting man has a special box with tools with which you can repair anything with your own hands. And such work as finishing the bathroom with plastic panels, he can do it too! To do this, you will need tools and materials:

drill;
screwdriver, screws and dowels;
hacksaw;
pencil, triangle, tape measure;
bath skirting board;
plastic moldings;
glue, sealant.

The list of materials can be supplemented depending on the method of fixing the cladding. Today, two methods are widely used: with and without a frame.

There is a huge number of different techniques and methods of wall decoration, you can simply get confused and confused when choosing the method that is needed for a particular separate task. However, in the event that it is necessary to quickly, efficiently and economically finish such premises as an entrance hall, kitchen, toilet, office, then it is recommended to use the technique of finishing the room with plastic panels (PVC). This recommendation is explained by the fact that plastic slabs for wall decoration are very strong, durable, have a high level of resistance to mechanical damage, as well as negative factors of moisture and fumes. The decoration of the bathroom with plastic panels is especially relevant, because it is here that the greatest accumulation of liquid and moisture, temperature changes and other favorable conditions for the reproduction of such an unpleasant thing as a fungus.

Installation of PVC panels does not require preliminary leveling of the walls with plaster or cement mixture. Installation is carried out "dry", without adhesives and mixtures. Also, manufacturers claim that plastic panels can be used faithfully for more than five years. However, it is recommended to pay attention to the fact that plastic panels, like any other product, do not tolerate high temperatures and open fire. But, at the same time, if any plate was damaged and part of it melted, then such a panel can be removed locally.

First of all, it is necessary to take out all unnecessary and interfering things from the room, since access to the entire wall surface is necessary. After that, the height of the wall is measured from floor to ceiling. Having carried out the measurement, the metal profiles are cut and adjusted to the desired height. Then, using a screwdriver, a level, metal fasteners with a step of 50 centimeters, from left to right, the profiles are mounted to the wall. This is done very simply.With a step of 40 centimeters in the direction from bottom to top, fasteners are screwed in one line, then the antennae of the fasteners are bent, the profiles are set at the level, using self-tapping screws for metal, the antennae of the fasteners are attached to the profile. Thus, a strong and reliable frame and base for the panels is formed. Image - DIY bathroom renovation with plastic panels in Khrushchev

Then, insulation is placed in the cells between the profiles and fixed, as a rule, foam is used. Since it is easy to stick to the surface, its thickness can be adjusted to the desired dimensions, the foam is easy to cut and shape into the desired shapes.

After completing the styrofoam laying, plastic panels are attached to the metal frame made of profiles. They are simply attached, the width of the wall is measured, the length of the panel is adjusted to such a measurement. After that, the panels are horizontally attached from bottom to top with self-tapping screws to the profiles. The final step is the bonding of the top and bottom skirting boards.

Frameless installation of plastic panels requires preliminary priming of the walls. Fastening of parts can be done with liquid nails. The consumption of glue varies from 1 to 3 cans per 5-6 sq. M. It depends on the degree of curvature of the walls.

Installation begins with the preparation of PVC panels. They should be cut with a hacksaw to the required length. Next, glue for plastic panels in the bathroom is dotted on the surface. It is advisable to apply the adhesive in a checkerboard pattern, 5-10 cm away from the edges of the panels to prevent spreading of the adhesive. Then the working surface is applied to the wall, slightly pressed down. This should be done carefully, since the panels are known for their fragility and pliability to mechanical stress.

Immediately after application, the panel is lifted from the wall for 5-8 minutes. During this time, it dries up, re-settles in its place, already finally. The process seems strange and time consuming, but in fact it is very simple and effective.

The cladding of the bathroom and toilet has been completed, the walls have been transformed and shine with novelty. Only one thing is upsetting - the ceiling, which violates the overall harmony of the renovated premises. You shouldn't think long about how to decorate the ceiling. It is quite possible to do with it in the same way as with the walls, namely, revet it with PVC panels.

For ceilings, glossy plates with a width of 20-25 cm are used. You cannot do without a frame. It should be installed according to the marks on the walls obtained using the water level. First, an initial mark is made on one wall, then they pass along all corners with a water level. Further, with the help of a special device - a chokline, the assembly lines are beaten off.

To install the ceiling frame, you will need two types of slats - 20x40 mm or 20x50 mm. They will act as profiles. Suitable material for slats - pine, spruce. These tree species are the most resistant to moisture, do not deform. The rails are fastened with U-shaped suspensions every 40-50 cm. In places where it is planned to place the lamps, you need to additionally strengthen the frame.

The fastening of the panels begins with the installation of the ceiling plinth. It is screwed to the frame in advance with self-tapping screws. Next, they begin to alternately insert plastic panels under the plinth, nailing them with a stapler or screwing them with screws from the working side. It is advisable to use screws with a press washer, since there is usually high humidity and temperature changes in the bathroom.

Lighting wires should be routed out when paneling the ceiling. The final moment in facing with PVC panels is the treatment of the seams with the Anti-Mold agent, waterproofing around the bathtub and toilet with Anti-Mold silicone.

Small apartments, popularly called "Khrushchevs", were a real salvation in Soviet times. They provided a roof over their heads for the numerous workers' proletariat. Nobody thought about the conveniences then.Five-story "Khrushchevkas" were built without attics with very small apartments.

Today, many "Khrushchevs" have gone through major repairs, and the owners of the apartments periodically improve their homes. The owners, who decided to make repairs in the bathroom with their own hands, wonder how to sheathe the bathroom with plastic panels? When the question arises of renovation in the bathroom and toilet, it is more correct to make a choice in favor of plastic panels. In addition to originality and ease of installation, they have a very liberal price.

When installing panels with your own hands in a "Khrushchev", the frame method is not suitable, since it "eats" about 8 cm of usable area. And in a miniature "Khrushchev" bathroom, such losses are very noticeable. The only correct solution would be to glue the sheathing to the wall with liquid nails.

In addition to their obvious advantages, PVC boards have another modest advantage. They are incredibly easy to care for. It is enough to wash them with warm water and detergent, wipe them with a dry cloth to avoid smudges and prints. It is categorically impossible to use abrasive detergents, brushes for cleaning panel walls in the bathroom and toilet. They injure the surface, dirt accumulates inside the cracks. The main problem for the bathroom and the combined toilet in the Khrushchev is the appearance of black mold. Any antifungal agent will help to cope with it. Soap stains can be removed with a solution of water and lemon juice in a ratio of 1 to 10. Dirt between the panels is removed with a rubber spatula.

Due to their anti-static properties, dust never settles on them. The bathroom will shine with novelty for several years!

Video (click to play).

Decorating the bathroom and toilet with PVC panels in Khrushchev is not too difficult and time-consuming. Any homeowner can handle this task with his own hands, having the necessary tools (drill, screwdriver, liquid nails). It is possible to cover the walls with plastic plates without any special technical training. PVC panels as a type of decorative cladding are the most affordable, and the result of the repair will delight the whole family!