DIY rear bumper repair Hyundai Solaris

In detail: do-it-yourself repair of the rear bumper of a Hyundai Solaris from a real master for the site my.housecope.com.

Work should be done with an assistant.
Operations are performed with an assistant on a viewing ditch or overpass.
We remove the mudguards and turn off the self-tapping screws for attaching the wheel arch liners to the rear bumper (see Removing the mudguards and wheel arch liners for the Hyundai Solaris).
We remove the rear lights (see Removing the rear light, replacing the Hyundai Solaris lamps).

From the bottom of the car, use a Phillips screwdriver to unscrew the clips of the two pistons attaching the bumper to the brackets of the bumper amplifier ...

… From the holes in the bumper and amplifier bracket.

The location of the pistons of the lower bumper attachment to the amplifier brackets.

Similarly, we take out the caps of the upper bumper attachment to the two brackets of the amplifier.

Using a 10 "head, turn off the self-tapping screws for attaching the bumper to the rear fenders on both sides of the car.

Under the rear lights, the bumper is attached with a piston and a self-tapping screw.

On the left side, use a Phillips screwdriver to unscrew the retainer and take out the piston.

Use a Phillips screwdriver to unscrew the self-tapping screw.
We perform similar operations on the right side.

Pulling, we separate the left side of the bumper from the body, overcoming the resistance of the clips of the plastic holder.
Supporting the left side of the bumper, pull the right side of the bumper away from the body in the same way ...

An amplifier is installed under the rear bumper.
To remove the rear bumper reinforcement ...

... on each side of the car, with the head "12", unscrew the two bolts securing the flanges of the bumper amplifier to the body ...

Install the amplifier and rear bumper in reverse order.

You will need: screwdrivers with flat and cross-shaped blades, keys "8", "10", "12".

Video (click to play).

1. Disconnect the wire from the negative terminal of the storage battery.

4.… and unscrew on each side one screw securing the rear bumper to the fender.

5. Remove one screw and one retainer for the bumper clips under the rear lights on the left and right, and remove the clips.

6. Unscrew the two clips of the lower bumper mounting clips ...

8. Remove the bumper from the plastic holders on the sides and slightly move the rear bumper away from the body.

9. From the inside, remove the screws of the two brackets securing the rear bumper to the amplifier.

10. Using a screwdriver, release the clips of the rear bumper lower mounting ...

12. Remove the four bolts (two on each side) securing the rear bumper to the body and remove the bolts.

This is how the rear bumper amplifier removed from the car looks.

14. To remove the reflector, unscrew the fastening screw from the inside of the rear bumper ...

15. ... and remove the reflector.

16. Install the rear bumper and all previously removed parts in reverse order.

Every vehicle owner can face the procedure for removing the bumper. But only at first glance it seems impossible. Most Hyundai car owners think that they will definitely have to go to the service station, but you can cope with this task yourself. How to properly remove this body element, you will learn below.

There can be quite a few reasons for dismantling this part on the Hyundai Solaris. Most often, car owners want to repaint it, remove scratches, dents, install parking sensors or directly replace the body element itself. In any case, dismantling the bumper is the same. And for this procedure, you need to stock up on such tools:

Phillips screwdriver
open-end wrench 10 mm;
sewn-in gloves.

Removing the rear bumper Hyundai Solaris (sedan)

If you have everything you need, and you have a lot of free time, you can start action. Start by removing the headlights from both sides of the bumper. To do this, you will need to unscrew three bolts on each side.

Be careful not to forget to disconnect the wiring harnesses first. When you remove the taillights, you will see two mounts that hold the bumper to the fenders of the car. They will also need to be unscrewed.

Under the headlights there are two pistons and two screws securing the bumper to the fenders.

In the event that you install parking sensors on a sedan, you will need to remove all the trim in the trunk. If you will be engaged in body repair work or painting a car, you can safely skip this point.

The attachment points of the bumper to the fenders are visible when the wheels are removed.

Now you need to remove the wheels, after which you will see three screws on each side. Feel free to unscrew them. Don't forget about the caps, which also work with a Phillips screwdriver. Now check everything carefully, and if you haven't forgotten about anything, you can remove the bumper from the Hyundai. Hook it up on both sides and gently pull it towards you. It will be good if someone will help you in this difficult procedure. Now you can safely start repairing a Hyundai car.

Usually, you have to dismantle the front bumper on the Hyundai Solaris if it has been damaged. This process is long and laborious, but the most important thing is to be patient and then you will succeed.

If you want to dismantle this part on the Solaris hatchback, then in addition to the above tools, you need to get a special puller for plastic panels. It will allow you to remove the interior trim without damaging the car itself. Here you need to act very carefully, since the risk is always present.

First, unscrew the screws that secure the rear bumper and remove the taillight. Now unscrew the screws that hold the brackets, they are located on the sides.

It is necessary to remove the parts located on both sides, and disconnect the plugs (andapki). Now you need to loosen the bolts on which the bumper is attached and carefully dismantle it. Do not forget to unscrew the fastening screw and remove the latch.

Removing the rear bumper Hyundai Solaris in the process

Now you just have to disconnect the most important connector that holds the bumper. Please note that the installation of this body element is carried out in the same way, but in reverse order.

If you follow the instructions, even a beginner will be able to replace the bumper on a Hyundai. Damage to a plastic bumper is quite common, so you need to be prepared for the fact that you may have to change or repair it several times a year.

Replacing a bumper with a Hyundai Solaris is carried out in two main cases: if it was damaged in an accident or unsuccessful parking, or if the driver has the intention to make a small tuning.

The sequence of operations for replacing the front and rear bumpers will be almost the same. The car owner will need an equipped garage and the usual set of tools, which the master always has. To carry out self-repair of the part, you will also need to prepare consumables.

The cars of the Korean manufacturer are equipped with inexpensive plastic parts, which often suffer from unsuccessful parking, especially since not all cars have parking sensors at their disposal. An automatic transmission sometimes reduces the incidence of accidental damage to a part, as the process of braking and stopping in vehicles with automatic transmission is smoother. Bumpers often suffer from unsuccessful contacts, cracks and weakening of the paint layer become their second problem. The dismantling and installation process will take a minimum of time.

The work will need to be carried out in a prepared garage. A slipway or a viewing hole will be required.It's just that on asphalt or ground it is extremely inconvenient to remove the rivets that hold the part in place. The inconvenient posture of the master when working to remove the bumper of a car standing on the asphalt will significantly lengthen the work time. Landing at the car is very low and it will be extremely inconvenient to remove the mudguards and protection. Also, the presence of a flyover will allow access to the screws that are located at the wheels of the car. If necessary, removing the luggage compartment trim is also more convenient to carry out in an equipped and clean garage.

In addition to the equipped place, you will also need a set of tools. Without them, even knowing how to replace the bumper with a Hyundai Solaris, you will not be able to cope with the work. Among the necessary equipment and tools:

screwdrivers, without fail - Phillips, and a key for 10;
sharp riveting tool;
a construction hair dryer that will help straighten the plastic of the bumper;
enamel and brushes, if necessary, then also painting, primer and putty. Parts made from a mixture of polypropylene and polyurethane are very capricious and require careful painting
drying chamber.

Most likely, the driver will need an assistant who will hold the volumetric part to work on replacing the bumper and subsequent repairs. Depending on the complexity and the presence of the overpass, the work will take from 30 minutes to several hours, if the driver has no experience of interacting with pistons and deeply hidden bolts. Before starting, it is better to study the instructional video additionally.

Replacement is usually required if the part has been damaged by unsuccessful contact with a wall, wood, or other machine. The result can be a dent or crack. Not everyone can correct these faults on their own; in case of a serious violation of the geometry of the part, it will most likely need to be replaced.

In addition to standard situations in which replacement or the need to remove the rear bumper of the Hyundai Solaris hatchback or sedan is required, there are also non-standard ones. Among them:

restyling;
installation of an original lighting solution;
the need to renew peeling enamel if the plastic part has been painted.

To get started, the car will need to be taken or towed to an equipped garage. Understanding how to remove the front bumper on the Hyundai Solaris, you need to prepare:

a place for repair, in which an overpass is installed or there is an inspection pit;
tools (their set depends on the types of work required);
details, if it is necessary to replace the bumper or trim on it;
get an assistant who can assist with repairs.

It will not be superfluous to watch the video in advance, in which the masters will tell you in detail and show how to remove the rear bumper of the Hyundai Solaris or change the front one. The sequence of actions must be strictly observed; violation of it may impede access to individual elements.

Removing the bumper is a simple operation, it does not take much time, unlike the possible repair of a part. Stages of work:

- the rivets holding the bumper are not very tight. They attach the part from the bottom, two on each side. The presence of the overpass will allow the driver to carry out this operation while standing. A Phillips screwdriver will help to remove the rivets, they can also be pry off with a flat sharp object;
- - then you need to find the screws located along the edges of the part from the inside, they hold the headlights. They are located extremely inconveniently - the car will have to turn the front wheels;
  - - then carefully unfasten the plastic fasteners that hold the replacement element at the sides. They are fragile and you will need to unfasten them very carefully so as not to break;
    - - the next step will be to remove the fog lights as carefully as possible;
        
        the work then moves under the hood. There, 4 bolts are unscrewed and two rivets are removed. There is a risk of losing the nuts, so prepare in advance and place a box under them;
        
        remove the bumper. You will need to install it after repair in the same order.
        
        A separate question will be how to remove the bumper cover on the Hyundai Solaris. Practically no effort is required for this: the part can be easily removed with a minimum of tools. It is supported by plastic fasteners that can be easily detached by hand. You only need to very carefully, but firmly press on them with your hands. With the same ease with which the cover is removed, it is put into place. The whole operation takes no more than 5 minutes.
        
        the caps located under the headlights are removed; this requires a Phillips screwdriver;
        
        the wheels cannot be removed or unscrewed, but you should try to remove the mudguards and plastic protection, which is held in place by three bolts;
        
        there are still two self-tapping screws in the corner of the bumper, they are removed, and the part dramatically stretches forward.
        
        Such a task as removing bumpers from Hyundai Solaris is solved easily and quickly, it does not require any special skills and is easily carried out independently.
        
        Few modern cars are equipped with metal bumpers, as most manufacturers prefer to use plastic for the manufacture of these body elements. This approach has both its advantages and disadvantages, but in any case, if the plastic bumper is damaged, the car owner gets more opportunities in terms of repair. Therefore, if you become a participant in an accident, as a result of which the body of your car was damaged, you can independently repair or replace its individual elements. Even without being a specialist in body repair, from the material of this article you can find out how to remove the front or rear bumper of the Hyundai Solaris, that is, to carry out a full dismantling.
        
        You can remove bumpers from Hyundai Solaris with your own hands
        In the process of preparing to remove the front or rear bumper, you should take into account the fact that Hyundai Solaris has a rather low stance. This can be difficult if your garage does not have a viewing hole, since some of the fasteners are located in hard-to-reach places. If it is not possible to install the machine on the inspection pit, you can jack up and support its front part, ensuring stability and preventing the possibility of rolling.
        
        From the tools that you will need for work, you need to prepare a Phillips screwdriver and a "10" wrench. In addition, it will be better if you provide good lighting at the dismantling site in order to work as accurately and accurately as possible, without damaging the plastic caps that fix the bumper on the outside. This point is very important, since it is quite difficult to find a replacement for these fasteners.
        
        Removing the front body element does not require much labor
        So, if one of the bumpers on your Hyundai needs to be replaced or repaired, check out the guide on how to remove the front bumper on Solaris, saving on the services of a master:
        
        After completing the preparatory operations, disconnect the terminal from the negative terminal of the battery.
        
        Find and unscrew two pistons on the left and right side of the bumper on the inside.
        
        Under the headlights, there are also bolts on the inside that need to be unscrewed. This operation can be somewhat inconvenient due to the difficult access, but the problem can be solved by slightly turning the wheels in the right direction.
        
        Remove the fog lights and open the six clips that are under the hood.
        
        After that, it remains only to unscrew the mounting bolts and the bumper can be removed.
        
        Disconnect the bumper where it is attached to the body
        As can be seen from the described operations, there is nothing difficult in dismantling. Certain difficulties arise in terms of access to some fastening elements. But in general, if you have a desire and knowledge at the level of a motorist about how to remove a bumper on a Hyundai Solaris, then there will be no problems during dismantling work.
        
        Considering that Solaris is available in sedan and hatchback bodies, the operations performed during the dismantling and replacement of some body elements may differ for these two variants. Therefore, we will look at how to remove the rear bumper, for both versions. Dismantling work on the sedan is carried out using the same set of tools as in the case of the front part.
        
        Even if you imagine for a minute that everyone around will start to drive carefully and carefully, you can hardly avoid minor troubles in the form of scratched or cracked plastic bumpers. High curbs, protruding fittings and the absence of parking sensors can give trouble with a damaged bumper. That is why, from time to time, replacing the Hyundai Solaris bumper with your own hands can be useful.
        
        5. Next, you need to disconnect the "fog lights".
        
        6. In the engine compartment, flip off the two rivets at the edges, then unscrew the four mounting bolts.
        
        Here you go bumper Hyundai Solaris removed and is ready for further work on it. If your bumper is dent without cracks or chips, then straightening it is quite simple. It is enough to have a construction hair dryer (and in some cases a usual one is enough), a little patience and the bumper will become the same as before. If the bumper is painted in any color, then you cannot do without a primer, putty and painting.
        
        This is how I had it before the repair:
        
        And this is how it became after the repair:
        
        This video will be useful for those who plan to align the dent on the bumper with their own hands. It helped me a lot personally.
        
        The attachment points are marked with a red square.
        
        We unscrew these two screws.
        
        The rear bumper of the Hyundai Solaris has been successfully dismantled. Let's drive carefully so that we don't have to change the bumper, good roads to everyone!
        
        Posted by admin in Auto 01.05.2018 0 45 Views
        
        Even if you imagine for a minute that everyone around will start to drive carefully and carefully, you can hardly avoid minor troubles in the form of scratched or cracked plastic bumpers. High curbs, protruding fittings and the lack of parking sensors can give trouble with a damaged bumper. That is why, from time to time, replacing the Hyundai Solaris bumper with your own hands can be useful.
        
        Fortunately, on Solaris, the front bumper can be removed quite simply, all the work will take no more than 20-30 minutes, and for dismantling we only need a 10 key and a Phillips screwdriver. It is advisable to carry out work on a viewing pit or on a lift, then you will not have to do acrobatics while lying under the car.
        
        We remove the bumper using the following algorithm:
        
        Be sure to disconnect the negative terminal of the battery, since you will have to work with the wiring, so we will avoid a short circuit.
        
        From below, the bumper is fixed with plastic caps, which are wedged with self-tapping screws. Unscrew four screws and take out the caps. We try not to confuse the fasteners, we put them separately.
        The bumper attachment points are marked with arrows.
        
        Installing a new one is carried out in the reverse order.
        
        The rear bumper is even easier to remove. On sedans, the luggage compartment lining can be left on, on hatchbacks, as a rule, the lining is removed to get to the rear lamp mountings.
        
        In general, the replacement algorithm on all bodies is the same:
        
        Disconnect the negative terminal from the battery.
        
        We remove both rear lights.
        
        2 pistons for fastening the rear bumper under the lights
        
        The attachment points are marked with a red square.
        
        We unscrew these two screws.
        
        The rear bumper of the Hyundai Solaris has been successfully dismantled. Let's drive carefully so that we don't have to change the bumper, good roads to everyone!
        
        You must be logged in to comment.
        
        When and how to polish the windshield? The windshield of a car is an effective tool for protecting the driver from weather and road conditions, providing a good overview and control of the traffic situation.
        
        Anti-scratch car windshield polishing - choice of means and procedure Over time, small scratches inevitably appear on the windshield.
        
        6. Modification variability We know that modification variability is a special case of non-hereditary variability. Modification variability is the ability of organisms with the same genotype to develop differently in different environmental conditions.
        
        The word modification The word modification in English letters (transliteration) - modifikatsiya The word modification consists of 11 letters: a d and i i k m o fts i Modification (Late Latin modificatio - change, from Latin modus - measure, type, image and facio - I do) aircraft - modification, transformation, imparting new properties to the original (basic) version of the aircraft.
        
        The meaning of the word modification Questions for the word modification in the crossword dictionary Economic dictionary of terms making progressive changes, transforming production, technology, products, creating an improved version, a new model; modified model of a product, machine.
        
        The best all-season tire - what all readers should look for when buying an Aloha. In this article, I decided to state my point of view on all-season tires, is it worth taking them, in which case it is yes and in which case it is not.
        
        Is it possible to ride all-season tires in winter The topic of our article will be multifaceted and ambiguous, since in its name and in its disclosure it contains a number of complex information.
        
        Is it possible to ride on all-season tires in the winter of 2016-2017? In 2015, in winter, a new regulation came into effect, which applies to the countries of the Customs Union. The bill says that in 2016-2017, restrictions on the minimum possible tread depth of tires for cars began to operate on the territory of these states.
        
        What varnish to cover acrylic paint - a glossy "defense" of brilliant beauty To find out what varnish to cover acrylic paint, we will consider the varieties of varnish compositions available for repair, we will choose the optimal ones and describe the procedure for its application.
        
        Can acrylic paint be varnished? Many people wonder whether it is necessary to varnish acrylic paint, the answer to which is simple - it is not necessary. Of course, it is possible to varnish the paint, but it makes no sense, since the varnish covers the surface that is not protected from the external environment.
        
        Can acrylic paint be varnished? Acrylic paint is actively used for painting almost any surface, it is highly wear-resistant, does not contain toxic substances, and dries quickly.
        
        Ideas for using washable chalk spray paint Now it has become fashionable to meet a mother and a baby from a maternity hospital on a grand scale, celebrate a bachelorette / bachelor party, ride around the city in a limousine in honor of a wedding or birthday.
        
        Chalk spray paint: scope and advantages Sometimes a car owner may want to additionally decorate the outside of his vehicle.
        
        Chalk paint: types, area of application Everyone who knows how and loves to draw knows how with the help of paints it is possible to embody design ideas. For example, chalk paint can give new life to interior items or help draw a bright congratulation, which can then be washed off with water, on almost any surface.
        
        Film filters: which tinting is better for a car and why? A certain part of car owners believe that tinted windows on a car are cool and significantly increase the status of its owner.
        
        Which tinting is better? Almost every car owner has a desire to tint his car. In this regard, the question arises as to which tinting is best for glass.
        
        Rating of tint films for cars 2017, the best tinting Many car owners, immediately after purchasing a car, think about what kind of tint film to buy for it.
        
        What is needed to paint a car It does not happen that a car is used for a long time and does not have scratches or dents on it. In addition, not everyone has a garage and a car standing on the street over time begins to rot and fade, the paint fades in the summer sun.
        
        How to paint a car with your own hands The reason for the unsatisfactory condition of the paintwork can be many factors: an accident, sandblasting and pebbles when driving at high speed, branches that leave scratches on the car body, or natural aging of the paintwork.
        
        We make a list of tools necessary for painting a car One of the problems that car owners may face is the violation of the integrity of the paintwork.
        
        A basic set for a novice nail extension master: what materials and tools are needed It is good that technologies in the beauty industry do not stand still, and that, 5-6 years ago, were available only to visitors to nail salons, now almost anyone can afford woman, and without leaving the house! The most enterprising people use this fact for additional income, the economical ones - so as not to run to the master with every broken nail, and those inclined to creativity - for the soul.
        
        8.1. Materials, tools 8.1. Materials, tools There are two types of engraving: deep and high. When deep, the paint lingers in the recesses, and it is removed from the convex parts of the board.
        
        Materials and tools for eyelash extension Increasing the length and volume of eyelashes is a very common cosmetic procedure. However, it can be done not only in a beauty salon, but also at home.
        
        Video (click to play).
        
        dgidaj57 ›Blog› Headlamp marking Due to changes in technical regulations in 2017, many people became interested in headlight marking. At present, vehicles are fitted with headlamps of the following approved types: C - low beam, R - high beam, CR - dual mode (low and high beam) light with incandescent lamps (UNECE Regulation No. 112, GOST R 41.112-2005); HC - low beam, HR - high beam, HCR - dual-mode light with halogen incandescent lamps (UNECE Regulations No. 112, GOST R 41.112-2005); DC - low beam, DR - high beam, DCR - dual-mode light with gas-discharge light sources (UNECE Regulations No. 98, GOST R 41.98-99). International designation of headlamp marking C - low beam R - high beam H - only with halogen headlight HCR - low and high beam with halogen bulb DC - low xenon DCR - high and low xenon PL - plastic lens S - headlamp (all-glass) B - fog lamp A - side light 02 - approval code Let us consider an example of the decoding of the markings applied to the housing or glass of a headlamp.
        
        Rate the article:
        
        Grade 3.2 who voted: 84