Washing machine ardo tl80e DIY repair

Read the recommendations for repairing the Ardo washing machine from the master!

The manufacturer (translated from Italian home appliances) is Antonio Merloni.

Front loading standard - FL models.
Drying - WD.

• 30% - blockage of the drain path, wear and damage to the pump:

We open the loading door, on the sticker we determine the model of the machine.

Having unscrewed the drain filter at the front at the bottom, we clean it.

We change the pump, which is located at the bottom right on the back side.

We loosen the clamp on the drain pump branch pipe.

We check the pump, clean it - in case of a malfunction, we change it.

Over time, mechanical wear appears on the shaft. The impeller dangles and does not pump out water well.

• 20% - malfunction of the electronic control board:

MINISEL board: Ardo models FL1000, FL1202, FLS81S, A800XEL, AE810, AE800X, SE810, FLS81S, AED1000X, TL1000EX, TL1010E ANNA610, ANNA 600X, A410, A610, A500, A1000.

We look at the power supply and the level of constant voltages (5 and 12 V) at its outputs. If there are no voltages at the IP output, check the corresponding elements - a power switch, a power filter, a power transformer T1, a rectifier (D11-D14), a U1 microcircuit.

Module DMPU: Models A800, A804, A810, A814, WD800X, S1000X, T80, T800, TL800X, TL804, etc.

Malfunctions in the DMPU module

breakage of resistances R51 (A, B);
stabilizer U3;
Zener diode D24 (short circuit);
open varistor VDR5.

relay K1, K2;
Rsimistor TR2.
Diodes D1-D6, D9-10, D15, D23.

A thing of the past module DMPA:

They are used in typewriters with an asychronous drive motor and a mechanical controller.

Models A1000PL, A1000XCZ, A1000XPL, WD1000PL, TL1000X, etc.

The wear of the heating element increases with “hard” water.

Overgrowing with scale (scab), it gives off heat poorly and burns out.

You need to pull out the gum and not the heating element. Since pulling out the heating element, you can wedge the gum.?

This is important to avoid further leakage under the seal.

• 10% - wear of brushes of the collector motor, loosening of contacts, breakage of the drive belt

Remove the belt, unscrew the screws and remove the engine. The motor has two brushes, each attached with two screws. We unscrew the screws and remove the brushes.

Inspect the board motor power supply terminal and ground wire.

Very often, the contacts are oxidized from moisture and the machine gives an error because of this.

Each brush is installed in a brush holder. It can be taken apart into two halves. Pay attention to how much the brush protrudes.

This size should be at least 1 cm. The best option is 1.5 cm. After that, we assemble everything and put it back in place.

• 10% - extraneous noise (bearings, shock absorbers, foreign object)

Having jammed the pulley, unscrew the upper shaft clamping nut counterclockwise.

If the oil seal is not filled with a specialized grease and the cross bushing is not lubricated with it during assembly, the oil seal will wear out very quickly, no matter what quality it is, this has been proven in practice.

It is not worth saving and improvising with lithol, grease and other lubricants, get better specialized lubricants that are used to lubricate the oil seals.

Standard sizes of Ardo bearings and seals:

This applies to modern technology - since 2000 (models AE800X, AED1000X, TL1OOOEX).

Thanks to it, you can diagnose (control module DMPU):

Close the hatch (without linen). Set the program selection to 30 ° C until it clicks. The temperature regulator to 0 ° C. Turn on. The drum rotates at 250 rpm. To check the buttons half load, additional rinse and others, press them. The spin speed increases from 250 to the maximum, provided for this model. In the absence of additional functions, press the spin button.

Indicators will blink when a malfunction is detected.

E00 | E01 - Draining. Clean the drain filter and drain connections.
E02 - The water is not supplied or drained off correctly.The drain hose may not be positioned correctly.
E03 - Water is not drained from the tank, also the drain time has exceeded 3 minutes.
F2 - Temperature sensor.
F4 - It is issued on the display if there is no water drain. A possible cause is a drain pump.
F5 - The water is drained and instantly poured. The problem is usually in the water supply filter.
F6 | F9 | F12 - Electronic module.
F8 - The water in the tank has exceeded the available level. Suspicion of an aquastop valve.
F13 | F14 - Critical.

Breakdowns are rare, usually associated with improper operation. Italian technology is distinguished by its high manufacturability and versatility.

How to carry out a service test equipped with the MINI-SEL board:

Control panels look different

The steps to enter the check mode are shown in the figures.

- move the program selector knob to the 6 o'clock position
- press button 4 - ENERGY WASH and, holding it down, press the POWER button.
After that, the CM should go into test mode.

With temperature control knob:

- turn the program selector knob to the 6 o'clock position
- move the temperature selection knob to the 9 o'clock position
- press and hold the ENERGY button (for at least 6 s), at the same time turn on the power supply of the CM with the POWER button.

After that, the CM should go into test mode.

Turning the selection knob, we check the devices:

Knob in position 1 (autotest) - NTC temperature sensor (sensor circuit - for open or short circuit), pressostat, display (if any), door lock and main function buttons on the control panel

2. First, the cold water inlet valve is opened until a signal is issued from the water pressure sensor. The filling of water takes place through the compartment of the dispenser for the PREVIEW.

3. First, the heating element turns on and the water in the tank heats up to 60 ° C. Then the CM drum starts to rotate in a cyclic mode at a speed of 45 rpm (as in a washing mode).

4. The drain pump (pump) turns on. At the same time, the drum starts to rotate as during spinning.

5. Within 10 s, the hot water filling valve is turned on (if this CM model has it). At the same time, the CM drum starts to rotate.

6. The fan and heating element of drying are included (for models with drying)

The test mode is exited by turning off the power with the POWER button.

Major breakdowns of the Ardo TL 80 E washing machine

Your machine stopped draining water, suddenly thundered during spinning, refused to turn on or turn off. Suddenly began to knock out plugs, stopped heating the water, does not rotate the drum, makes an extraneous sound when rotating, does not block the hatch, are the brushes worn out?

Contact our service center by phone

8(495)565-38-25 and 8(499)409-84-95 or use the online application form

Washing machine breakdown diagnostics - free of charge in case of repair

• Removing foreign objects from the washing machine - from 1000 rubles.
• replacement or repair of engine brushes - from 1500 rubles.
• replacement or repair of the door handle - from 1200 rubles.
• replacement or repair of glass in the door - from 1500 rubles.
• replacement or repair of the door lock - from 1300 rubles.
• replacement or repair of the washing machine engine - from 2000 rubles.
• replacement or repair of the pump - from 2000 rubles.
• replacement or repair of the heating element of the washing machine - from 2000 rubles.
• replacement or repair of bearings in the drum - from 2500 rubles.
• replacement or repair of the drive belt of the drum of the washing machine - from 1500 rubles.
• repair of the electronic control panel - from 2500 rubles.

• Freestanding installation
• Loading type vertical
• Maximum load of laundry 5 kg
• Drying no
• Electronic control (intelligent)
• Dimensions (WxDxH) 40x60x90 cm
• White colour

Efficiency and energy consumption classes

• Electricity consumption class A
• Washing efficiency class A
• Spin efficiency class D
• Energy consumption 0.19 kW * h / kg
• Water consumption per wash 59 l

• Rotation speed during spinning up to 800 rpm
• Cancel spin yes

• Partial protection against water leaks (body)
• Childproof no
• Imbalance control is
• Foam level control is

• Number of programs 15
• Bio-enzyme phase is
• Wool washing program yes
• Special programs for washing delicate fabrics, economy wash, express wash, pre-wash

Other functions and features

• Tank material plastic
• Additional options for choosing the washing temperature

Urgent repair of washing machines at home

departure of the master on the day of contact in Moscow - free *

fault diagnostics - free of charge

warranty for work performed up to 12 months.

consultations by phone : 8 (495) 565-38-25 and 8 (499) 409-84-95

Our company offers comprehensive solutions to any problems in the field of repair of Ardo washing machines. Service center "Golden Hands" will pay special attention to your every wish. We improve our work by using new technologies.

Extensive experience in the repair of washing machines. We offer you the services of real professionals. Order the Ardo washing machine repair service in Moscow at competitive prices. Our discounts are real savings with the Golden Hands company.

The customers of the "Golden Hands" company are guaranteed the quality of the work performed. We offer professional advice from specialists. Service Center "Golden Hands" is proud of its impeccable reputation.

Any household appliances fail sooner or later. In some cases, this is physical wear and tear of parts and components of the unit, in others, incorrect connection and operation, and in others, marriage. We will devote this article to such a technique as Ardo washing machines, consider their typical breakdowns, the reasons for such breakdowns, and how to repair Ardo washing machines with our own hands.

The user understands about the breakdown of the washing machine based on specific symptoms. Only after studying these symptoms, he can assume a breakdown of a particular unit. Therefore, we will start by listing the most common symptoms.

• The machine has stopped draining water. This can happen for several reasons, the main of which is the clogging of the drain system, which includes: a branch pipe, a drain hose and a pump. In very rare cases, the water does not drain due to a breakdown of the water level sensor.
• The machine does not heat up the water, especially when washing 60-90 0 C. The reason for this malfunction is the breakdown of the heating element, which burns out due to limescale and settling scale. But the development of the resource of the heating element is also possible.
• The drum does not rotate in the machine, it stands still. In Ardo washing machines, the tank rotates due to the drive belt, and if it breaks or falls off the pulley, the machine will stop. The problem is solved by replacing the drive belt.
• Extraneous sounds appeared in the typewriter, similar to knocking or crashing. If such a knock is heard when the machine is turned off, then the reason is clearly in faulty bearings. Another reason for the rumble can be a foreign object in the tank.
• Is there water leaking under the machine? The reason must be looked for in the drain filter or pipes. In the worst case, you need to change the oil seals and bearings.
• Programs get lost or the machine does not turn on at all, which means that the reason lies in a malfunction of the electronic board.

Before you panic and call the master, take a close look and listen to the "symptoms" that appear, perhaps you yourself can find the cause or even carry out repairs yourself.

In many washing machines, the manufacturer has programmed error codes into the microprocessor, which appear on the display in the event of a malfunction. Here are some examples of codes of common malfunctions. A all codes of any Ardo model can be found in the instructions.

• E00 or E01 - no water drainage due to clogged drain filter.
• E02 - incorrect draining during spinning, the position of the drain hose is violated.
• E03 or F4 - the drain time is exceeded, the drain pump is broken.
• F2 - problems with the temperature sensor, heating element or control board.
• F5 - self-draining, wrong connection of hoses.
• F13 or F14 - malfunction in the control module.

Having found out the cause of the malfunction, we determine - call the master or we will repair it ourselves. In some situations, it really is not worth overpaying, but doing the repair yourself. For example, blockages that have arisen can be removed. Most of the garbage accumulates in the drain filter, so cleaning it belongs to minor repairs and can cost about 600 rubles. Although in fact, there is nothing complicated about it:

• Open a small door at the bottom of the front of the machine or remove the bottom panel.
• Then place a large, absorbent cloth on the floor in the area of ​​the filter.
• Unscrew the valve counterclockwise.
• Pull out the filter.
• Rinse it well with water, remove hair and other debris.
• Screw the filter back on.

The problem is debris can become clogged not only in the filter, but also in the drain hose, nozzles and the drain pump... To get to them, you will have to open the car body. And this is classified as repairs of medium complexity, the price for which starts from 1,200 rubles, and if a malfunction of a spare part is found during the disassembly of the machine, then you will have to buy a spare part as well.

If a foreign object gets stuck in the tank, such as a bra bone, then you will have to completely disassemble the machine. Such repairs are assessed as difficult and will cost at least 2,000 rubles. And if you are wondering how you can get an item out of the car, then you can read an article on how to remove a bra bone from a typewriter.

You can replace or clean the pump yourself if you have free time and skills in working with simple tools.

In the Ardo washing machine, you can get to the pump from the bottom, it is either absent, or the plastic strip can be easily removed. The entire algorithm of actions and video instructions are in an article on our website on how to clean the drain pump in a washing machine.

If it is necessary to clean the drain hose, then one end of it must be pulled out of the sewer pipe, and the other must be disconnected from the pipe coming from the pump. Then the hose itself is cleaned with a flexible cable, at the end of which there is a small brush. After that, the hose must be rinsed under running water, wiped and connected in place.

Quite often, a heating element fails in washing machines. Diagnosing its malfunction is simple: when washing things in water heated to 60 0 C, put your hand to the drum hatch. And if it is cold, it means one thing - the ten is burnt out, you will have to change it. Replacing a heating element refers to repairs of medium complexity, the cost of which will cost up to 2,000 rubles plus the cost of the heating element. But do not rush, because getting to the heating element is not difficult and you can do this through the back cover of the case, for this:

1. We disconnect the machine from the network, disconnect it from the water supply and sewerage system, deploy it so that it is convenient to work.
2. We unscrew the self-tapping screws around the perimeter of the machine that hold the cover.
3. We find contacts and wires coming from the heating element under the tank, remove the terminals and sensors.
4. We unscrew the bolt that secures the heating element.
5. Gently, with blabbing movements, we pull the ten on ourselves, you can pick up the ten with a screwdriver.
6. We clean the heating element holder from debris.
7. We take the original heating element for the Ardo typewriter, insert it into the holder for the heating element, so that the sealing gum completely fits into place.
8. We tighten the bolt, connect all the terminals.
9. We collect the machine.

Pay attention! Regular cleaning of the washing machine from scale will extend the life of the heating element, but you should not rely on advertised water softeners.

Replacing the electronic module is also not difficult and belongs to the middle class. However, this is in the case when there is confidence that the module will have to be completely replaced one hundred percent. But in some situations, the module can be repaired by replacing individual elements on it. This is of particular importance, because the module itself is quite expensive, in some models its price is one third of the price for the entire machine. It is not uncommon for people to refuse such repairs and buy a new automatic machine.

Working with electronics is specific, it is necessary to possess not only the skills of working with tools, but also knowledge in a certain area. Therefore, in such a situation, it is better to contact a specialist who accurately diagnoses the malfunction and can replace the element correctly.

For your information! There were times when some craftsmen independently changed the control module, connecting all terminals and sensors, and as a result, the new module burned out.

The most difficult repair, according to experts, is the replacement of bearings and oil seals in Ardo washing machines. This is because you have to almost completely disassemble the machine and take out the tank, and the bearings themselves are difficult to remove. Special tools, patience and dexterity may be required. In such a situation, it is much wiser to give the car to the craftsmen than to repair it in your apartment, where there is not much room to turn around.

For those who still want to save money or gain experience in repairing washing machines, we suggest watching a detailed video on replacing bearings.

Thus, only after assessing the complexity of the repair and your real abilities, you can begin to eliminate the malfunction yourself. Sometimes it is better to pay a technician than to pay twice later for a failed repair attempt.

Elimination options:
1. It is necessary to check the presence of water in the water supply. It is trite, but very often the reason for the appearance of an imaginary malfunction is such funny things.

2. The inlet hose is squashed or clogged. We check visually for the absence of compression. We unscrew the hose from the washing machine, turn on the tap and see if the water will pass through? Of course, care must be taken to ensure that the water does not drain onto the floor. If the water does not come out, we find and remove the blockage. The hose with a leakage valve after the protection has been triggered will have to be replaced with a new one.

3. The filler mesh on the back of the washing machine is cleaned. The mesh is quite fine and often clogged with rust or other particles from the tap water. The filter can be easily removed with pliers and cleaned thoroughly.

4. It is necessary to make sure that the filling valve is in good working order. It is located just behind the filter. The valve becomes accessible after removing the top cover of the washing machine. Perhaps, the wires of its power have come off or frayed. To check the functionality, the valve itself can be removed and connected to the voltage indicated on its body. Should open. If it does not work, you will have to change the valve to a new one.

5. The problem may be related to a faulty water level sensor. Or, in another way, the pressure switch. You can also find it under the top cover. It is removed quite easily. It is held on the body of the washing machine by screws or latches. We check the integrity of the wires and their connection to the sensor. A tube comes up to the pressure switch from below. It may be clogged. The simplest test for the performance of the sensor after removing it is to blow into its tube. If you hear a click, the pressure switch is most likely working properly. Otherwise, you will have to change to a new one. It is important not to mix up the wires when installing a new one.

Common causes and solutions:
1. Again, about the banal - you need to make sure that the sewer pipe is not clogged. Maybe the car just has nowhere to drain the water. Of course, this is possible with machines with a permanently connected drain. We also check the drain hose of the washing machine. It should not be kinked or twisted. In principle, you can disconnect the hose from the sewer and check if water comes out of it when draining? If it does, we clean the sewer system. If not, check the hose for clogging. Problem still exists? We look further.

2. The drain filter is clogged. Simple, but the most common reason for the lack of a drain.The filter is located at the bottom of the washing machine under the door or decorative panel. It is a screw plug screwed into the machine body using a standard right-hand thread. Accordingly, the filter is unscrewed counterclockwise. Do not forget to place a tray under the washing machine to collect the flowing water. After removal, the filter is cleaned of impurities. You will need to remove the excess in the place where the filter was installed. Next, reverse the process and check the drain. Most often it helps.

3. Blocked or faulty drain pump. A common problem for Ardo washing machines is the blocking of the pump due to foreign objects entering it. Various coins, buttons and other items left in the pockets of the washed clothes, getting inside the drain pump, prevent it from performing its functions. A symptom of a blockage of a working pump - at the moment the drain is turned on, the pump hums, tries to expel water, but cannot. Another option is that the pump has become completely unusable. In any case, he will have to be removed. In Ardo washing machines, it is very easy to access the drain pump from the bottom of the machine. They have no bottom or are covered with an easily removable plastic strip. It is enough to lay the car on one side and the access is open. Before removing, you can check the operation of the pump with a multimeter. Further, the clamp of the rubber pipe is loosened and it is separated from the pump. The same procedure is for the drain hose. Power wires are disconnected. It remains to unscrew the screws that hold the pump and remove it. A serviceable pump is disassembled. And foreign objects are removed from it. The defective one is replaced with a new one.

4. The lack of drainage can be caused by incorrect operation of the pressure switch. It simply may not send a signal to the control module to drain. We have already discussed what needs to be done with the water level sensor above.

2. A rare, but possible breakdown option is a malfunction of the temperature sensor. It is checked by measuring the resistance at room temperature and when heated with hot water. A non-working sensor is simply replaced.

3. It is necessary to make sure that there is no "sticking" of the contact group of the heating element relay on the control module.