Washing machine leaked from the bottom reasons do it yourself repair

In detail: the washing machine leaked from the bottom of the reasons do-it-yourself repairs from a real master for the site my.housecope.com.

Every day in advertisements on TV, there is so much talk about problems with the washing machine, but for some reason it seems that this trouble will never come to our house.

The water on the bathroom floor plunges many into shock and stupor. However, at the same time, you need to get together and act in order to solve the problem as quickly as possible. Today we will talk about why water flows from under the washing machine and how to get rid of these problems.

Consider the actions to be taken immediately after a leak is detected:

When you see water on the floor, do not step into it.

That is why unplug this appliance from the socket. If this does not work, turn off the electricity in the entire apartment or private house.

Limit the water supply to the clipper. This can be done in two ways: by shutting off the water supply tap leading to the device, or by stopping the flow of water into the entire system of the living space.

Using the drain filter (located in the front in the lower right corner) drain the remaining water.

Unscrew the laundry.

Start inspecting this household appliance.

There are several reasons due to which the washing machine also flows from below when drawing water or spinning, and in each case, different repair methods are required. Let's analyze the main breakdowns:

The reason is in the hose

If water leaks out at the junction of the hose and body, the small gasket between the two needs to be replaced.
Leakage in the area of the drain filter... Most often occurs after the filter was once unscrewed, and then it was not pressed enough, which caused the appearance of water on the floor.

Video (click to play).

Dispenser problem... We are talking about a small container (pull-out or built-in) into which the washing powder is poured. It is possible to determine that the cause of the breakdown is precisely because of him according to this simple rule: water flows immediately after it enters the machine.

The main factors affecting the breakdown of the dispenser are as follows:

the grate is clogged due to large grains of powder not dissolved in water;
too much sediment resulting from poor water quality;
very strong water pressure.

The reason is in the pipes... It occurs quite often because manufacturers make them from low-grade materials, saving money and time in the final production of finished household appliances.

The door cuff may also leak.... This problem occurs only in washing machines with a side loading method.

It leaks due to the fact that belts and shoes are loaded along with ordinary linen during the washing process, small change and various sharp objects fall out of pockets.

Leakage during spinning... This happens when the oil seal has become unusable or there is too much water in the tank.

What if the toilet cistern does not hold water? This article will help you find the answer.

Want to change your bathroom faucet? We will help you choose a mixer and install it.

If you do not pay attention to the leak in time, this as a result can lead to even greater consequences: one breakdown will lead to the failure of another component.

At the same time, do not forget that living in a multi-storey building, the constant flow in your bathroom will one day lead to the fact that, in addition to repairing your washing machine, you will have to make repairs in the bathroom located on the lower floor.

There are many ways to repair a washing machine, but they all depend on what was the cause of the breakdown. That is why we will give the main ways to eliminate the causes of leakage of this household appliance, to cope with which without the help of a wizard:

washing machine hose is leaking

Video (click to play).

Such a repair is more acceptable for the drain hose. As for the hose responsible for the water supply, its better to replace immediatelyto avoid trouble in the future.

If found leak in the area of the drain filter, then it is completely unscrewed, and then screwed well until it stops. It should be remembered that you do not need to apply a lot of effort, otherwise you can break the thread.

For problems with the dispenser it is removed from the machine, well cleaned of the accumulated dirt on it and returned to its original place. You will be able to check the health of the entire device when the machine starts to wash again. If it turns out that the water still flows out, you will have to call a specialist.

Damaged intake valve tube need to replace. For this, the upper part of the household appliance is removed and dismantled.

If there is a problem with the pipe that is responsible for the collection of water, it is disconnected from the surface, greased with good glue and the pipe is installed back. The area around the adhesion of these two materials treated with sealant... After waiting for the glue to dry completely, they begin to wash again.

Having considered all the reasons due to which the washing machine flows from below, and the main ways to eliminate them, we can conclude that you need to pay attention to any malfunctions in time... When you cannot fix the problem yourself, contact a professional.

When a hostess buys a washing machine, she often expects that the washing machine will work for a long time, delighting with clean clothes, without breaking. But unexpected breakdown is possible. Breakdowns can be very different, but visually the device usually leaks from the bottom. Let's figure out why the washing machine is flowing from below, and what to do in case of such a nuisance. It should be understood that no one is insured against breakdowns in the washing machine, so it can happen to the most thrifty and tidy owner. If you purchased expensive equipment, this does not mean that it is not susceptible to breakdowns, this happens with high-quality LG washing machines. In order to react in time to a breakdown that has arisen, and then correct it correctly, you should carefully study the information given in this article. In it you will find an explanation of the cause of the leak, the occurrence of malfunctions. We will tell you how to fix a breakdown, how to prevent equipment, what to do if a leak occurs at an unexpected time.

There are several main reasons why the washing machine is leaking from below, here are the main ones:

improper use of washing equipment;
use of low-quality chemicals for washing;
factory defect in the manufacture of parts or elements;
failure of a part or element.

When the device is completely emptied, then you should understand where the cause of the leak is, what kind of breakdown occurred. It is better for a master to make diagnostics. Let's consider what are the reasons in more detail and how to determine their occurrence if the washing technique is leaking.

A washing machine is a device that constantly works with liquid substances; it contains hoses.It is not difficult to identify a cut or crack in the hoses if they are leaking, and this can be done even with an idle machine. You can wrap the hose with toilet paper, where it gets wet, there is the damage that led to the leak. If it turns out that a leak has arisen at the junction of the hose and the body of the washing machine, then dismantle it from the body and replace the gasket. If it turns out that a leak has arisen on the hose itself, then it must be replaced completely, the repair will be either of poor quality, or will save it from the leak for a short time.

If the washing machine leaks when you turn it on, after filling in with water, it may mean that the detergent dispenser has broken. This can happen when using a poor-quality chemical agent, poor water, or when clogged with powder or due to the powerful pressure of water. Also, a foreign object may fall into the tray or it may simply become clogged with powder.

The branch pipe may break after 12 months from the beginning of the operation of the washing machine, it happens less often with LG machines. This breakdown is connected with unscrupulous manufacturers who are trying to save money on everything.

If the main leak occurs during water intake, then the problem is most likely with the pipe. To make sure that this is really the case, you will have to remove the top cover from the machine.

It happens that the drain pipe starts to flow to the drain pump from the tank. You can verify this by tilting the washing machine and looking from below. The branch pipe for filling water into the tank may start to leak. To check this, you will have to untwist the front wall and inspect the junction. To eliminate the problem, you will need moisture-resistant glue, which you need to thoroughly lubricate the connection point of the branch pipe.

If water leaks from the hatch where the clothes are loaded, then the sealing cuffs are damaged. It can be repaired or replaced; for a quality repair, you should call a master. To avoid such damage, carefully check the pockets of your clothes before loading them into the washing machine. Small items often remain in pockets, which with pointed edges can damage the cuff and lead to leakage.

Minor cuts in the cuff can be repaired with a patch of rubber and waterproof glue. If the damage is large, a complete cuff replacement will be required.

Problems with the tank can arise if you often wash not only clothes, but also shoes, belts, clothes with metal elements, which gradually damage the surface of the tank and lead to breakage. If a crack appears in the tank, then it will have to be changed, and this will take money and a lot of time. You can try to seal the crack, but more often than not, this does not end well.

The tank consists of several parts, which are connected using brackets or bolts, with a gasket that connects them. Over time, the gasket is damaged and then a leak occurs, after which it may be necessary to replace the gasket.

If a leak occurs during spinning, it means one thing - the oil seal is damaged, immediate repair is needed. It is important to remember that the oil seal will wear out over time, which immediately leads to leakage during spinning. To check the condition of the oil seal, you need to inspect the tank. By the way, during the inspection, there may be a need to change not only the oil seal, but also the bearings.

If you decide to do without the help of a wizard and troubleshoot yourself, then you should be careful, if you do wrong, you can only make it worse. Warranty service does not apply if you were doing repairs at home on your own.

If a leak begins at the bottom of the washing machine, then you should perform the following steps one by one in time on your own:

turn off the equipment from the power supply. Unplug the machine from the outlet carefully, and do not allow water to come into contact with you.This will prevent possible troubles, primarily electric shock. If you cannot turn off without contact with water, then you should turn off the entire electricity system in the switchboard;
as soon as a leak occurs, turn off the water supply;
as the washing machine is turned off, open the door, remove all clothes from the washing machine. At the end of the wash, you should drain the remaining water from the machine through the drain filter, which is at the bottom, in front of the washing machine, at least for LG.

Then we proceed to the detection and elimination of the resulting breakdown. If the hoses are damaged, after finding the place of leakage, you can begin to eliminate the hole (if you decide to repair, and not replace the hose). The hose can be repaired with a waterproof glue and a rubber patch. If it turns out that the problem lies in the gasket between the hose and the body, then you should unscrew and release it. Then replace the old gasket with a new one purchased in advance. After the manipulations, assemble the structure back.

If it turns out that the problem is related to the dispenser and the equipment is leaking, it means that it is necessary to eliminate the malfunctions in it. Remove the dispenser from the device, clean it properly, if a blockage is found, remove it. Then you need to return the dispenser back and test the operation of the equipment. It is necessary to check how strong the pressure is, if necessary, slightly close the inlet valve, reducing the pressure. If all these manipulations did not help, this can mean one thing - the inlet valve is badly damaged, it can only be repaired by a specialist in the repair of washing machines.

Another reason for the leakage of the washing machine may be the loss of integrity and elasticity of the main cuff, which is installed on the loading hatch. To check the integrity of the cuff, whether it is leaking, you need to open the hatch to examine the condition. If minor damage is found, they can be repaired with waterproof glue and rubber patches. Remove the clips-clamps and the place that was patched up, move to the bottom of the hatch, then return the clips to their place. If it turns out that the cuff is badly damaged, then you need to order a new one replacing the old one.

If you decide to check and repair the inlet valve pipe, then you will need to remove the top cover of your washing machine, then start examining the part. If the condition of the pipes has visible damage, or the pipes have acquired an appearance that differs from the norm, then they should be replaced, which means that the pipe is leaking. A branch pipe of this type is a complex part that will be replaced by a qualified technician. The filler pipe of the washing tub may also break. Check if there is water at the junction, which means you need to disconnect the filler pipe, remove excess glue, remove all liquid and dry the junction thoroughly. Then return the pipe to its place, while fixing it with high quality waterproof glue. For these purposes, you can also use an epoxy mixture.

You will need third-party help to fix problems with the tank. Let the assistant tilt the washing machine and hold it, then you can examine the general condition of the bottom of the machine. If equipment is loaded from above, then the side wall should be inspected. The purpose of the inspection is to detect traces of liquid. If water is found on the wall or bottom, then the problem is definitely related to the operation of the tank. This is one way out - call a specialist, it is impossible to repair the tank yourself, if it leaks.

If a leak occurs during spinning, it means that the oil seal has broken or the bearings have become unusable. In this case, you need to contact the master, he will repair the apparatus and replace the main bearings.

The overall service life of parts and equipment depends on how you use it. To avoid the problem of leakage, you need to adhere to certain recommendations:

metal parts of clothing can damage the drum, then you should adhere to a certain rule: wash all clothes with metal parts in a special bag. You should also do with small things, they can be sucked into the drain pipe of the machine;
before closing the main cover of the washing machine, make sure that the drum door is closed securely. This is the case if your washing machine is top-loading, like some LG models. This will prevent leaks during spinning;
when the wash is over, do not forget to unplug the equipment from the outlet - a voltage surge can disable it;
it is better to install the washing machine where there is less humidity, for example, in the kitchen;
do not overload with things, then the washing machine will work for a long time and it will not happen that it leaks during spinning;
if low-quality water flows in the water supply system, install a filter in the system;
and most importantly - do not use low-quality detergents, this will certainly lead to breakdown, and you will wonder why the machine is leaking, what to do now.

If you constantly monitor and take care of the equipment, it will not break at an unexpected moment and will last a long enough time, it will not happen that the washing machine leaks.

When we buy a new washing machine, we expect that it will serve us for a long time and please us with clean things. All washing machines have a different service life, and it depends not only on the factory defect, but also on its correct operation.

One of the frequent breakdowns in washing machines is leakage. It looks like this: water flows from the bottom of the washing machine. Water can drip little by little or "beat with a fountain" - in either case, urgent repairs are needed, which you can do yourself or call a master.

If you are accustomed to personally eliminating any breakdowns of equipment and repairing it, then this information will be very useful for you. After all, it is here that we will analyze the reasons for the leakage of the washing machine, as well as ways to eliminate this malfunction.

We visually find the place of the leak
Before starting any repair work on the washing machine, disconnect the power supply by unplugging the power cord. You also need to pay attention to the moment at which the washer is leaking, - this information will allow you to more accurately determine the cause of the leak.

After that, visually inspect the place where the water flows from. To do this, you need to tilt the washing machine or completely remove the side or rear wall from it. Try to pinpoint the location of the leak as accurately as possible, then read below about the causes and remedies.

One of the most common reasons for water leaks from under the washing machine is hose wear and poor connections at the joints.

Inlet hose

If the inlet hose is leaking, you will find the leak even when the washing machine is not running. Carefully inspect the joints of this hose with the body of the washing machine, and also check its integrity. Replace it if necessary or, if the connection is poor, change the gasket and tighten well.

Drain hose
If you find that the washing machine is leaking when draining water or during spinning, and the place of the leak is the drain hose, then most likely it is simply damaged. First, check the junction of this hose with the washing machine pump and inspect the hose itself. Replace the drain hose if necessary.

Leaking pipes
If you notice that most of the water runs out from under the machine during water intake, and after filling it, the water no longer flows, then the likely cause of such a breakdown is a damaged a branch pipe that goes from the filler valve to the hopper for the powder receptacle.

In order to check the integrity of this pipe, you will need to remove the top cover from the washing machine.

Second a branch pipe that can leak - drain... It goes from the tank to the drain pump. To check it for integrity, you need to look at it from below by tilting the washing machine.

The third pipe that can leak during water collection is branch pipe for filling water into the tank... To get to it, you will need to remove the front wall from the washing machine, and then inspect the connections of this pipe. If it is he who flows, then most likely the connection of the branch pipe with the tank is simply ruined.

If it is attached with glue, then you will need to detach it, clean it and dry it well. Next, you need a good moisture resistant glue or epoxy. Smear the junction of the pipe to the tank and glue it in place. Let the glue dry well, after which you can start checking the washing machine.

The machine may leak if the drain pump is unusable or damaged. If it flows from it, then inspect it visually, unscrew it if necessary and check its integrity. More often than not, it just changes to a new one and the problem is solved.

On our website you can read about replacing the pump in the washing machine yourself.

Very often, users of washing machines forget to pull small things out of their pockets, it even happens that sharp objects come across, which during washing can damage the cuff of the washing machine, which, in turn, causes leakage through it.

In such cases, there are two options for solving the problem:

Repair of the cuff
If the damage to the cuff is small, you can simply seal it with waterproof glue and a patch. The patch can be made from rubber, or you can buy a boat patch from a fishing or travel store. After you have sealed the hole, it is best to turn the cuff so that the patch is on top - this way there will be less stress on it and, accordingly, it will last longer.

Replacing the cuff
Of course, if the cuff is damaged, it is best to replace it completely. To do this, you need to remove the old cuff and put a new one in its place. You can see how to do this in the video below.

If you notice that water is flowing through the tank, then there may be several reasons, which we will discuss with you in order.Crack in the tank
Washing machine tanks are usually made of plastic and are therefore relatively fragile. If you washed things with small change or other metal objects, then one of these objects could get into the space between the tub and the drum of the washing machine and damage the tub.If there is a crack in the tank, then it must be changed, which is a rather expensive and troublesome undertaking. You can, of course, try to seal the crack with moisture-resistant glue, but this solution will not give a good result, so it is best to replace the tank.
Image - The washing machine leaked from the bottom reasons do it yourself repair

Tank halves connections
Most often, the tank in a washing machine consists of two halves, which are interconnected by brackets or bolts, and a gasket is located between them. This very gasket dries out over time and can leak, which is extremely rare. In order for you to replace it, you will have to disassemble the washing machine almost entirely.

If you notice that the machine is leaking from the side of the bearings, then this means only one thing - the oil seal is worn out, which requires replacement. Usually, with such a breakdown, most of the water flows during the spin cycle.

Replacing the oil seal is a rather difficult task that occurs along with the replacement of bearings. Therefore, to eliminate this problem, we recommend that you call the wizard. If you decide to carry out repairs yourself, then read the article on replacing bearings in a washing machine.

Leaking powder tray
Check the powder tray for foreign objects or powder residues. Just take it out and see if there are any smudges on it, clean it if necessary.

If the water pressure in the tap is too high, then water may also spill out during the rinsing of the powder from the powder receptacle. You can reduce the water pressure by slightly turning the washer tap on your water pipes.

Also, with some washing machines, it happens that the edges of the washing powder tray wear out, as a result of which the machine begins to gradually leak through it. For more information on this problem and how to solve it, see the video.

Pump drain valve not twisted
If you have recently cleaned the drain valve, then it is possible that you did not tighten it well, and water flows through it. Remove the bottom panel and check if the valve is tight and not leaking.General recommendations
If your washing machine leaks from below, this is the first sign of improper operation and non-compliance with the rules for using the equipment. Therefore, to prevent such incidents from happening, always remove all items from your pockets before washing, repair the machine in time if any breakdown is found in it - after all, one malfunction can cause another.When buying a new washing machine, people rely on its long and trouble-free operation. But any household appliance has its own shelf life, and it is determined not only by the reputation of the manufacturer, but also by the correct operation. That is why many owners sooner or later face the fact that their washing machine is flowing from the bottom.This is one of the most common faults. If water has flowed onto the floor - it doesn't matter if it drips or runs in a stream, an urgent need to repair the washing machine on your own or call a master.If you prefer to troubleshoot home appliances yourself, this article will probably come in handy for you. Let us consider in detail the reasons for the leakage of the washing machine and the methods of its repair.

Washing machine dispenser hopper clogged.

Tank not sealed (crack or breakdown appeared).

One of the hoses (drain or inlet) has been damaged.

The pump is leaking.

Tank oil seal worn out.

The door rubber cuff is leaking.

One of the pipes has lost its tightness.

Before starting repair work, you need to de-energize the equipment by removing the plug from the outlet. Then you need to figure out which of the many elements of the washing machine is leaking. To do this, the washing machine must be carefully inspected.

It is extremely important to find out the cause of the breakdown at what stage of the operating cycle the washing machine began to leak from below. This will greatly facilitate the troubleshooting task and will allow you to detect 1 of 3 possible leak locations. Leakage locations such as:

Drain and inlet hoses for water often leak where they dock with the unit. To get rid of such a breakdown, you need to unscrew the hose for filling or draining water and change the rubber gasket.

But it also happens that the hose has worn out, or was accidentally damaged, then to restore its integrity, you can use a special glue and a rubber patch, although replacing it with a new one would be a more reliable option. But all of these recommendations are suitable for the drain hose. If the inlet hose has been damaged, we do not recommend repairing it with a patch, since the water pressure in it can be very high, and then replacement becomes the best option. You can buy a water inlet hose at any plumbing store, moreover, inexpensively.

The dispenser may be damaged because of a malfunction in the hopper (i.e. powder compartment). As a rule, it leaks when it is clogged, either due to excessive water pressure, or due to a failure of the intake valve. What to do in such a situation?If it’s a valve, you’ll see leaks in the area below it. To eliminate the causes of the leak, remove the dispenser and thoroughly clean it and the hopper.It so happens that a foreign object appears in the drain of the bunker, which does not allow it to work normally. If you find such an item, remove it from the powder compartment. Image - The washing machine leaked from the bottom reasons do it yourself repair

After cleaning, test the operation of the washing machine. In addition, it is worth trying to reduce the water pressure by slightly closing the tap. If none of the above helps to cope with the leak from the bottom, it is necessary to replace the inlet valve, since it is its breakdown that can cause the high water pressure during the rinsing phase.

It is not uncommon for many people to forget to remove all items from the pockets of their clothes before loading them into the washing machine, and many of them can be very sharp. As a result, the cuff on the door of the washing machine is damaged during the wash process and begins to leak.

In such a situation, you can fix the breakdown in one of 2 ways:

Repair. If the hole is small, try covering it with moisture resistant glue and a rubber patch. You can also purchase a custom boat patch from your fishing specialty shop. After sealing the hole, the hatch cuff should be installed in such a way that a piece of patch rubber is placed on top - this will reduce the pressure on it and, therefore, increase its service life. Since the collar can also be damaged on the inside, we recommend dismantling it to seal the holes.
Replacement. If the damage caused is too great, a complete replacement of the cuff of the washing machine hatch will be required, for which you need to do the following: dismantle the faulty cuff and install a new one instead.

It is likely that the reason why water began to flow from the water supply hose is the weakening of the attachment of the nozzle to the tank of the machine. To find out if this is so, a thorough examination of the tank is required. If you see traces of water leaks, then the problem has been found.

To repair or replace the inlet hose of the washing machine, you need to remove the branch pipe, then clean all sections of the joints from the remaining glue and dry them. Then you can re-fix the branch pipe, for fixing which you need epoxy resin or high-quality moisture-resistant glue.

If you saw that it is the tank that leaks, there may be two reasons for such a breakdown, we will consider them in detail.

The buck is cracked. Tanks in automatic machines are most often made of plastic, which is why their reliability is rather low. If you forget to empty the pockets of your clothes, during the operation of the unit, one of the objects in them could fall out of the pockets and damage the tank.

If the tank is cracked, it will need to be replaced, which is a very expensive and complicated process. Of course, you can try to remove the crack yourself using waterproof glue, but this is unlikely to help you for a long time, because the tank will most likely need to be changed, and this will have to be done with the help of a specialist.

The joints of the tank parts. As a rule, the tank of the automatic machine includes 2 elements connected to each other by metal brackets or screws, and in the space between them there is a rubber gasket. Such pads dry out over the years and begin to leak. To change the gasket, the device must be almost completely disassembled.

See also -Do-it-yourself repair of a washing machine tank leak

If the washing machine leaks from the bearings, the reason is the wear of the oil seal, which means that you cannot do without replacing it. Most often, with such a malfunction, the main volume of water flows out during the spinning process.

If an oil seal leak is found, turn off the machine immediately, because due to water, the bearings can rust and also break, and this will lead to more serious problems.

Changing the oil seal is not easy for a layman, since the process will also require replacing the bearings of the washing machine. That is why we advise you to contact a professional to repair such a breakdown.If you still want to repair the unit on your own, before that you will need to understand how the bearings are replaced.

If you have been cleaning the drain valve not so long ago, it is possible that after the end of the procedure you forgot to carefully screw it in, and as a result, a leak has formed. Take out the bottom panel and make sure that the valve is screwed in completely. The main reason for the appearance of a leak in the washing machine is mistakes made during its operation. Therefore, in order to avoid such breakdowns, we recommend that you always check the pockets of your clothes before loading them into the machine, and promptly carry out repair work at the first detection of any malfunction.

The washing machine has become an integral part of the modern home. After all, it is much more convenient to use it than to wash the laundry by hand. It saves us time and effort. This means that using it, we make our life better. How nice it is when there is no need to do the laundry yourself. You can entrust this part of the household with household appliances. And you yourself can enjoy more pleasant business or relaxation. But, unfortunately, there comes a time when any home appliances become faulty.

You may have noticed during or after washing that your washing machine is leaking. It is unpleasant when a puddle has formed on the floor. And of course this problem needs to be solved. After all, no one wants to wipe the floor after each wash, removing the accumulated moisture. In addition, sooner or later, you can flood your neighbors. And this is not what we need. Therefore, it is necessary to identify and remove the causes of the leakage of the washing machine.

If the machine is leaking, there may be several reasons. A large number of models of washing machines are presented on the modern home appliance market. Different models may have different disadvantages. And their weak points, which, with long-term use, can cause breakdown, causing water leakage. Let's take a look at the most common ones. Those that are most often the place of leakage.

Has water appeared under the body of the machine? Check how much there is. And above all, make sure it’s the washing machine and not some other reason.

The pump (drain pump) may leak.
It is possible that the tightness of the tank is broken (a crack or breakdown has appeared).
The integrity of the hoses is broken (both the drain and the inlet hose can be damaged).
A damaged door cuff leaks.
The connections of the filler pipe are not tight.
The pipes connecting the inlet valve and the dispenser of the washing machine are not tight.
The oil seal of the tank is worn out.
The machine's dispenser hopper is clogged.
A damaged tank drain pipe is leaking.

Before starting repairs, you must de-energize the washing machine by unplugging it from the outlet.

Then you need to understand from what point of our machine the water flowed. First, let's take a closer look at it. By the way, did you notice at what point in the wash cycle our washing machine started to leak? It is necessary to find out the answer to this question. It will greatly simplify the troubleshooting process. This approach will help us find one of three possible leak locations. The following places of water flow are perfectly determined by visual inspection:

Inlet hose.
Drain hose
Washing machine door cuff.
And the dispenser hopper.

Defective hoses. Hoses often leak where they dock with the washing machine. In order to eliminate this nuisance, we can unscrew them and replace the rubber gasket.

If the drain hose itself has rubbed off or is accidentally punctured, then in the case of the drain hose, you can restore its integrity using special glue and a rubber patch, but it would be better to just change it to a new one. In the event of a breakdown of the inlet hose, we strongly advise against repairing it. Since there is quite a lot of pressure in it, it is easier to replace it.They are sold in plumbing stores and are not quite expensive.

Dispenser malfunction. The dispenser may have a faulty hopper (this is the depression into which the washing powder is poured). Its leakage can occur due to the fact that it clogged. And also due to the excessive pressure of water in the pipes. And due to problems with the operation of the intake valve.

In the latter case, you will be able to notice traces of drips under its location.

In order to eliminate the causes of the leak, we must get the dispenser. And clean both the hopper itself and the dispenser. In some cases, an object gets into the drain part of the hopper that interferes with normal operation. If you find such an item, be sure to remove it from the machine.

After cleaning, check the operation of the washing machine. Also try to reduce the head by slightly closing the inlet valve.

If neither the first nor the second step did not solve the problem, then it is necessary to change the inlet valve. Since its malfunction may cause increased pressure during rinsing.

In some cases, a leak can occur due to a violation of the seal of the hatch cuff. If the outer part of the cuff is damaged, you will notice leaks from the front of the washing machine. If the inner one is damaged, then it will flow from the inside.

If the hole is small, you can remedy the situation with waterproof glue and a rubber patch. It is also advisable to remove the clamps that fix the cuff and change the position of the place with the patch by moving it to the top of the hatch. If the damage is large, then it makes sense to order a new cuff and replace the one that is leaking. Instructions for self-replacement of the cuff in the following video:

It is possible that the attachment point of the branch pipe with the washing machine tank is loose. In order to understand whether this is the case, it is necessary to inspect the tank. If traces of water are visible on it, at the junction with the pipe, then we have found the reason.

To fix it, we need to disconnect the pipe. Then remove the remnants of the glue, remove moisture from the joint and dry it. After that, we can return the pipe to its place, fixing it with "epoxy" or reliable waterproof glue.

It is necessary to remove the upper part of the machine body and conduct a thorough inspection of the pipes. If we notice that the problem is in them, then we eliminate it by replacing the pipes.

For inspection, we need to tilt the washing machine so that we can inspect the bottom. You will need to use a flashlight for a thorough inspection. We are looking for traces of water. If the loading of your washing machine is vertical, then to check it is necessary to remove the side of the case.

Damage to the tank can occur for various reasons, for example, plastic tanks break down due to the ingress of a solid object or a malfunction of the heating element. If you have found a leak in the tank, then it must be replaced.

The process of changing the tank is extremely difficult. It may be easier for you to see a specialist.

Washing machine oil seal is periodically worn out. As a rule, if the oil seal is faulty, you may notice a leak during spinning. In order to verify this problem, you need to inspect the tank. If you notice traces of water leakage from the bearings, you will have to change both the oil seal and the bearings themselves.

If the drain pipe of the tank has leaked, it is necessary to seal the leakage with rubber or replace it. It is located at the bottom of the machine and connects the tank to the pump (drain pump).

If the drain pump has leaked, then it is easier to replace it. Video instruction for replacing the pump (drain pump):