Washing machine samsung diy bearing repair

Details: Samsung washing machine DIY bearing repair from a real master for the site my.housecope.com.

Even reliable Samsung cars require attention, especially after 5-7 years of operation. While replacing the hose, cuff and belt are easy tasks, replacing the drum bearing on a Samsung washing machine can take effort, time, and money.

On the latter, you can save money if you try to do everything yourself.

Replacing a bearing in a Samsung washing machine is the only right solution in the event of a breakdown, since repair of this component is often impossible.

It is worth starting preparation for work with the search for suitable spare parts. Now the market (both shops, service centers, and on the Internet) offers a huge selection of bearings for any models of Samsung washing machines. In the kit you will receive:

In order not to confuse and not to buy an unsuitable set, tell the seller the exact model and year of manufacture of your washing machine. To make it easier to navigate, look at the table of spare parts for Samsung typewriters:

In addition to the part itself, you need to prepare a small set of tools. To dismantle the fasteners, unscrew the tank into 2 parts, knock out the bearings, arm yourself:

a small copper hammer;
grease or WD-40;
bent hex key;
marker;
metal hairpin;
pliers;
adjustable wrench;
keys of various modifications;
indicator, negative and positive screwdrivers;
sealant.

All this will help you to replace the bearing with your own hands according to all the rules.

Having collected all the necessary tools, you can begin to figure out how to replace a bearing in a Samsung washing machine.

Prepare a comfortable place in which you will disassemble the machine - it may not be enough in the bathroom, so if possible, transfer the equipment to a workshop or garage.

Video (click to play).

Next, you need to remove the "extra" parts that interfere with the dismantling of the tank. You need to disassemble in sequence so as not to lose parts and fasteners, so carefully sort and lay out everything that you remove from the car.

Disassemble the CM case according to the following scheme:

Remove the top panel. To do this, unscrew the two fasteners located at the corners on the back wall. Then take the lid with both hands and pull it towards you, and then up. After removing the panel, set it aside so it does not get in the way.
Remove the detergent drawer. It's as easy as shelling pears:

pull the tray out to the maximum;
press the valve located in the middle;
with the other hand, slightly lift the tray and pull it towards you;
if you did everything correctly, the receiver will jump off.

After removing the powder receiver, unscrew the hoses that supply water to it, as well as the branch pipe through which the dissolved powder is poured into the tank. Unclench the clamps using pliers.
At the top of the washer you will see a counterweight. It looks like a large brick or stone. Choose a suitable head to unscrew the fasteners.

Carefully! The counterweight is heavy, do not drop it on yourself or onto the machine.

Next, you will need to dismantle the gum seal.

Removing the rubber cuff on a Samsung washing machine is easy:

Remove the two bolts that hold the sunroof lock.
Remove the sensor - this is necessary in order not to break the wiring when removing the cuff.
Use a thin screwdriver to pry off the wire clamp.
Guide the screwdriver under the clamp until you bump into the hardware. Your task is to weaken it.
Loosen the bolt and remove the clamp.
With your fingers under the cuff, pull it towards you.

You may not need to fully pull out the seal.The point is that it does not interfere with the removal of the front panel.

Next, lay the clipper on its side to gain access to the bottom of the MCA. Remove the bottom by unscrewing the 4 screws holding the cover. Set it aside.

Get started electronics:

Locate the engine and drain pump. Remove all wiring connected to these parts. If possible, record the disassembly process on video so that you do not confuse all the wires later. If this is inconvenient, then mark everything using a marker.

Important! The pins that connect the wire to the sensors are very weak, so try not to damage them. If you find burnt contacts or wires, replace them immediately.

Now you need to remove the racks - replacing the bearing of a Samsung washing machine is impossible with them. The ends of the posts are attached to the tank with four bolts, on the other side the posts are screwed to the machine body.

Do not remove anything at the bottom except the motor. The pump will not hurt you either - it will only be enough to remove the pipes going to it.

Leave the washer in a horizontal position - so it will be more convenient for you to remove the water inlet valve along with the pipes and sensors running to it.

Remove the wire connected to the valve sensor, then unscrew the fasteners that hold it in place. Remove the valve, set aside. Finally, remove the 4 springs that hold the tank.

Now there is nothing left to get to the tank - you only need to remove the wall and the front cover. The control panel is held in place by 5 bolts. By unscrewing them, you can easily remove it.

The main thing is not to damage the control panel wiring!

The front wall is held in place by about a dozen fasteners. Find them all and unscrew. Remove the cover and set aside. By the way, under the front cover there is another smaller counterweight than the main one. Take a socket wrench and unscrew it.

Now everything that previously prevented you from getting the tank has been eliminated. You can get the engine and the tank. It is important not to damage the wiring and other vulnerable components, so as not to add work to yourself.

Turn the tank over.
Remove the belt from the pulley.
Unscrew the pulley with a hexagon. If the pulley fasteners are tight, drip some WD-40 to avoid ripping off the bolt.

You have coped with the routine work and disassembled almost the entire machine. Now, you can disassemble the tank to see live what bearings are in your Samsung washing machine and make sure that they need to be replaced.

Since the racks have already been unscrewed earlier, it remains to remove only the clamps and brackets. The tools will help you with this. There are usually no special subtleties and difficulties with this work.

Remove the top of the tank body to expose the drum. Then remove the bottom. As a result, you should have:

The upper half of the tank with a hatch hole in the center.
The lower half of the tank with a heater.
Drum and axle.

Since you have done this kind of work, do not focus only on the bearings - check everything that you have access to along the way.

For example, you can check the inside of the tank for damage, or check the heating element for dirt and scale, short circuit and breakdown to the case (the last two checks are done by a tester). If you find problems with the heater, you can clean it from limescale or completely replace it with a similar one.

Before replacing a bearing on a washing machine, you need to get it out. Follow this scheme:

In the tank bushing you will find 2 bearings of different sizes.
To get a large one, it must be knocked out from the outside towards the tank using a hairpin.
The smaller one is knocked out from the inside of the tank.
Take a pin, place it against the edge of the bearing and tap it lightly with a hammer. Lean the stud against the second edge and tap again lightly - so walk around the entire circumference of the bearing until it pops out.

Attention! When knocking out a part, never hit the same place. There should be at least 3 points for whipping.Otherwise, the bearing will come out crooked or it may get stuck in the bushing, and you will have unnecessary problems.

By the way, you can remove bearings in any auto repair shop - locksmiths have special pullers. Therefore, if there is such an opportunity, you can contact the specialists. Usually they do this work for a nominal fee.

remove the used items;
take a clean cloth and wipe the inside of the sleeve;
lubricate the new oil seals with the grease that comes with the bearings;
install the oil seals.

Then you can fit the bearings. Do it this way:

install the part in the bushing and put it there with your fingers;
put a wooden block on the second bearing;
hit the part several times until it sits down.

If you still do not know how much a bearing for a Samsung washing machine costs, then we warn you that a good part costs about 600 rubles. And if you do something wrong, you will have to buy again and again or contact a master.

We will list the typical mistakes of amateur craftsmen, so that you can see how to do no need... Most often, home craftsmen make the following mistakes:

cut off the UBL wiring;
tearing the cuff;
damage the pulley by removing it from the axle;
break off the fastening bolts;
cut off the wiring of the temperature sensor or heating element;
tear off the pipes if they forgot to remove or loosen the clamps;
break the sleeve when knocking out the bearings (in this case, you need to change the drum).

You need to know these errors so as not to repeat them yourself during the repair process. If something does not work out or is forgotten, it is better to read the article again or print the instructions and act strictly according to it.

Bookmark our site so you don't miss out on valuable bearing replacement tips.

Replacing the drum bearing of the Samsung washing machine is a common procedure in workshops and service centers. This part undergoes a powerful load during operation, therefore it often fails. Replacing the bearing of a Samsung washing machine with your own hands is a painstaking, troublesome job. This is due to the design features. The back wall of Samsung models is deaf, cannot be removed. Be prepared for the fact that the machine will have to be disassembled almost to the cog in order to get to the drum. By conscientiously removing all interfering parts, you will preserve their integrity while pulling out the tank. Ready to bring your washer back to life? We will help you with practical advice, links to useful resources.

To find a suitable repair kit, you need the full model name. It is located above the barcode of the service sticker on the back of the washing machine.

Take a photo or rewrite the name - specialists will help you choose a spare part. Possibly the required modification is indicated in the table.

Then it is easy to buy a bearing from an online store. The last way is to disassemble the machine to see which bearings are in the Samsung washer. This option has one big plus - by dismantling the SM parts, you can find other defects, breakdowns (belt, crosspiece, pipes), immediately buy everything you need.

The price ranges from 100 to 700 rubles. To replace, you will need 2 bearings - internal, external, always a new oil seal. Therefore, it is more advisable to purchase a repair kit. The cost is 1000-2000 rubles.

First, prepare the machine for the procedure:

Disconnect from the electrical network, communications.
Move away from the wall, remove from the closet, niche, from under the sink - you need some room to maneuver, good lighting.
Stock up on tools: a set of screwdrivers, a screwdriver, socket wrenches, a hammer, a rag, grease, a repair kit, a marker, a camera, a screw press.
Prepare a place for the removed assemblies, panels, fasteners.

The main process will also have to be carried out in several stages. Do not forget to photograph the results of your labors, take pictures with your camera. This will make it easier to put everything back together. Let's get started:

Choose a suitable screwdriver, attachment for your favorite screwdriver, unscrew the rear bolts that secure the cover.
Pay attention to the presence of plastic washers, spacers - put everything in one place so as not to lose.
Push the cover in front of you to release the fasteners from the slots.
When the surface moves forward, lift it up, carefully remove it.

Remove the powder receptacle by pinching the inner latch with your finger.
This will open access to two self-tapping screws that hold the front panel, the powder hopper - unscrew them.

Remove the control panel by disconnecting the wires. Samsung's CM wiring is smart. Terminals, connectors are decorated in different shapes, colors, so it will be difficult to confuse something during reassembly. But if in doubt, you can take a picture, number with a marker.
After removing the module, you will see the self-tapping screws that hold the top of the main front wall.
Detach the bottom panel by gently prying it off with a screwdriver - this will open up access to the lower wall mounts.
Before unscrewing the main screws, remove the metal clamp securing the hatch collar. To do this, pry the spring with a flat screwdriver.

Insert the cuff into the drum. Now you can remove the front panel.

Now that access to the internal components is open, remove the water supply valve, filler, air nozzles, carefully disconnect the water level sensor.

When removing the drain pipe at the bottom of the machine, substitute the container - it often contains water after washing.
Disconnect the bottom wiring - heating element, engine, pump, sensors, ground. Take the bundle of wires to the side, secure so that it does not interfere, does not get damaged when removing other parts.
Use a socket wrench to unscrew the shock absorber mountings, concrete counterweights.
Now you can pull out the plastic tank by removing it from the springs.
Dismantle all elements that may interfere: motor, belt, shock absorbers.
Separate the halves of the tank by prying metal latch springs along the perimeter of the container.

Remove the pulley. A socket wrench with a 17 head will come in handy.

Gently knock out the shaft with a hammer, take out the drum.
There are bearings and an oil seal on the back of the tank.

Pay attention to the seat before replacing the kit. If there is a large output on the shaft, notches, it makes sense to change the cross, otherwise replacing the bearings will not give the desired effect.

Remove the oil seal.
Carefully drive the large bearing into the tank wall, the small one out.
Clean the bushing from scale, rust, lubricate with special grease.
Lubricate the oil seal, rings - refit.
Ready! It remains only to assemble the washing machine in the reverse order. The video will help you to carry out the procedure for dismantling, repairing, assembling yourself:

As you can see, the scope of work is not comic. But if you are a techie at heart, you have a set of tools, the necessary components - step by step you will cope with this matter. We wish you a successful renovation!

If during washing in a Samsung washing machine you hear an extraneous hum - this is the first sign that something is happening with the drum shaft bearing. Do not wait for the moment when it collapses and shaft production begins - repairs can be very expensive for you, and you may have to buy a new assistant. Replacing bearings in a timely manner will save you the trouble.

Washing machine bearings perform a very important task - they contribute to the correct and even rotation of the drum. Due to the fact that the latter makes a large number of revolutions, they quickly fail and must be replaced in a timely manner.

Worn bearings can cause a malfunction in the washing and spinning process, as well as loud noise during the operation of the machine. If parts are not replaced in time, the drum may fail, the repair of which will cost you dearly.

First of all, when you need to change bearings that have failed, you need to choose an identical kit so that there are no problems during installation.

The bearings in the machine of this brand must be replaced: they not repaired... Before starting to disassemble the washing machine, you need to purchase new spare parts, where in one package you will be offered:

set of bearings;
seals for sealing;
grease of a special composition.

Repair kits are produced strictly for each Samsung model, so write down the model number of your washing machine before going to the store.

In addition to new bearings, you need to stock up on the necessary dismantling tool fastening the pipes, the tank itself, disconnecting the wires:

An ordinary hammer or made of copper, so as not to cause mechanical damage.
Standard set of open-end wrenches and sockets.
Pliers.
Steel hairpin.
Marker.
Screwdrivers (slotted and cross) and indicator.
Small adjustable wrench.
Silicone based sealant.
Mobile phone with a camera.

The camera is necessary to photograph all the components before dismantling, especially the initial connection of the wires.

First dismantle top cover on the washing machine, by unscrewing the two mounting screws (or self-tapping screws) from the back, which are located in the corners, after that we move the cover, raise it.

Then we shoot detergent dispenser, it is easy to do it without special knowledge and skills:

open all the way;
with your thumb, lightly press on the tongue in the central section, at the same time slightly raise the device and pull it towards you;
if everything is done correctly, the dispenser will come out of the fixing point.

Now let's get down to dismantling hosessupplying water to the section of the dispenser and the branch pipe through which the water with the dissolved powder enters the tank. Maximum care is required so as not to damage the fastening of the clamps: using the pliers, we unclench the fastening, pull the hoses from the place of their connection.

We shoot counterweight - we carry out the disconnection very carefully, holding its body with our free hand. We unscrew the two bolts using the corresponding head and remove it to the side.

When unscrewing the last fixing bolt, hold the counterweight, because it is heavy and accidentally sliding down may damage important parts of the machine.

The cuff interferes with the removal of the front panel, so remove it first. It is attached to the panel with yokes, and the other side is put on the drum. We find the spring connecting the ends of the holder, pry it off and remove it together with the clamp. Now you can remove the edge of the cuff and tuck it into the tank so it doesn't get in the way.

We close the hatch, find screws from above and below and unscrew them. Now the panel is held only by a small hook. We carefully remove it so as not to damage the wire connecting the hatch lock to the rest of the car's wiring. Disconnect the wire by removing connector... We put the panel aside so that it does not interfere with us.

To do this, carefully put the machine on one side, unscrew the four mounting bolts, and remove the bottom to the side. Now we can clearly see the electric motor and the drain pump. First you need to disconnect everything wires, taking a picture, so that later you do not get confused in their connection.

Pay special attention! The contacts of the connections are quite delicate, so we exercise maximum caution, if you notice burning, replace the terminal.

Dismantle tank mounts on the bottom of the washing machine, disconnecting the fasteners on the tank itself and the bottom of the case. There is no need to unscrew anything other than the engine: the drain pump does not interfere, you just need to disconnect the inlet pipes.

The car is also on the side, and we go back to the top of it and dismantle sensors and nozzles filling valve. First, we disconnect the wire, then the fastening bolts, take out the valve body and put it aside.

Now you can disconnect counterweights in the form of four springs that hold the tank in suspension with a drum inside. We dismantled everything that interfered with the free removal of the tank through the top, it remained to remove the control panel. It must be removed carefully so as not to damage the wires and connection terminals. We removed the front wall in advance, we still need to remove the small counterweight at the bottom of the machine.

We carry out this operation with the utmost care so as not to damage any contact, otherwise additional repairs may be required, which is not our intention.

Turn the tank over so that there is free access to the belt drive: remove belt, dismantle with a hex wrench pulley housing.

Advice! The pulley bolt may stick along the thread. In order not to break the thread during dismantling, treat it with WD-40 grease - after a while it will unscrew quite easily.

The tank has been dismantled and is located outside the body of the machine, all the necessary photos have been taken, so we proceed to disassemble the tank in order to get to the drum and replace the bearings.

The racks have already been dismantled, so the two halves of the tank are held only on brackets and special clamps, when removed, there are no problems - it is enough to pull them off with open-end wrench and screwdrivers.

As a result of disassembly, we got three fairly large elements:

upper part with a hatch hole in the middle;
the lower body of the tank with a heating element;
the drum itself with the shaft.

Examine other items carefully as you get to the bearing mounting assembly. If a breakage or scale is found, defects should be eliminated: clean the tank and the heating element from scale, ring the element for failure, replace if necessary.

Read also: DIY repair of vanos m62

There are two bearings in the bushing of the tank body: a large one and a small one. The first one is knocked out from the outside to the inside with the help of a steel pin, the second - vice versa. We knock out the bearing housing by applying alternately with a hammer diametrically opposite light blows to hairpin, attached to its edge, moving in a circle until the body is completely released.

Remember! To prevent the bearing from jamming, you need to hit at different points. Otherwise, you will create problems for yourself that cannot be solved without a special tool.

After removing the old bearings, we remove oil seals, wipe the inside of the sleeve with a clean rag. We take out new oil seals from the repair kit, apply grease, insert them into place. Install new bearings should be careful:

We put into the sleeve with our hands, as far as it goes.
Place a small piece of wood on top of the bearing housing.
With light hammer blows on the wood, we install the bearing in its original place.

That's the whole technology of replacing a bearing in a Samsung washing machine, it remains only to assemble the machine in the reverse order. We lubricate both halves of the tank with a thin layer of sealant, the leak path will be blocked very reliably. The repair algorithm for other brands of washing machines has certain nuances. On our website you can also find articles about replacing bearings on washing machines Ariston, LG and Indesit.

When replacing these parts on their own, users often make a number of mistakes that can only complicate the problem:

damage to the cuff of the hatch;
a break in the wire coming from the sensor that blocks the hatch;
damage to the shaft pulley during its removal from the axis;
breakage of wires from the temperature sensor and heating element;
damage to the mounting bolts;
failure of the branch pipes due to the fact that they forgot to loosen the clamp;
damage to the sleeve in the process of knocking the bearings out of the drum, as a result of which the latter will require replacement.

These errors will only add to the problems, so it is better not to get down to work if you cannot afford to repair the washing machine.

If you are far from technical, then seek professional help. For those who are familiar with household appliances - a video to help.

Owners of home appliances of a well-known South Korean brand will be interested in how a Samsung washing machine is repaired with their own hands.Unfortunately, sometimes it is necessary to eliminate breakdowns and leaks of washing machines, even in an expensive price segment, and knowledge of error codes and related malfunctions may also be required.First, you should familiarize yourself a little with the main features of these machines. First, it is stylish design. Image - Washing machine samsung do-it-yourself bearing repair

Secondly, it is the original design of the drum. Modern modifications of Samsung washing machines are equipped with a fundamentally new technical solution - Drum Diamond Drum .

It belongs to an innovative type of honeycomb drums with a surface covered with many convex pyramids and small water holes, into which the fabric is not drawn.

Thanks to this design, a gentle wash cycle is provided. These drums can be very spacious - with a load of up to 12 kg of laundry, depending on the model of the machine.

Thirdly, worthy of attention heaters with double ceramic coatingnot covered with limescale, and inverter motorattached directly to the drum in some modifications.

Also interesting are the functions Fuzzy Logic and Smart Check responsible for the correct calculation of the washing mode depending on the amount of loaded laundry, as well as for diagnosing various machine malfunctions.

The number of wash programs depends on the model of the washing machine. Even the simplest modifications are equipped with all the necessary set of programs, and the new models have a washing mode called ECO Bubble - with the help of air bubbles, laundry is easier to wash even in cold water.

If the machine is marked with Wf, it means that this model is front-loaded, and if its name contains the abbreviation WD, it means that the machine is equipped with a built-in dryer.

But Samsung brand machines also have one small drawback - their instability to voltage drops in the network, which is important in our Russian reality.

When the voltage becomes either too high or low, then a control system called Volt Control simply turns off the washing mode to resume it immediately after the mains voltage has stabilized. This is not always convenient, so it is better to connect the washing machine through a voltage regulator.

After a short acquaintance with the parameters of this brand, let's move on to considering the main breakdowns.

To understand the malfunction that has arisen, you need to consider the most common of them and the reasons for their occurrence.

Here is a list of common problems:

Further, the methods of repairing them with your own hands will be considered, because it is not always possible to call the master. And for this you need to have a set of necessary tools.

Before starting repairs, you need to make sure that all the tools from this list are available:

flat and Phillips screwdrivers or screwdriver;
set of wrenches;
pliers, pliers, wire cutters;
tweezers - elongated and curved;
powerful flashlight;
long-handled mirror;
soldering iron;
gas-burner;
small hammer;
knife.

In addition to the listed tools, you may need a magnet to pull out small metal objects inside the machine, a long metal ruler to align the drum, a multimeter or voltage indicator.

But that's not all. In addition to the required set of instruments, the following building materials will need to be purchased for repairs:

sealant;
Super glue;
insulating resin;
soldering materials - rosin, flux, etc .;
wires;
clamps;
current fuses;
rust remover;
electrical tape and scotch tape.

Sometimes a multimeter is not needed, it is enough to turn on the machine and select a mode with a high water temperature.From the operation of an apartment electricity meter, it is easy to understand whether the heating element is receiving power.

If you are a beginner, then you can advise using a camera to shoot a video or to photograph a workflow, so as not to confuse the sequence of actions and then assemble the machine correctly.

There are several important rules to remember that must be followed before starting repair work:

it is necessary to drain all the water from the machine;
before disassembly, be sure to (!) disconnect the device from the power supply;
choose a bright and spacious enough place for renovation.

If the unit cannot be moved to a convenient location, then ensure maximum illumination of the workplace.

The first step is to remove the top panel of the washing machine.

The second step is to take out the container for powders, this is not difficult to do. Next, you need to remove the cuff from the hatch. Caution is needed here. Use a screwdriver to pry the retaining clip, remove it, and then remove the O-ring. This should be done carefully, trying not to tear the soft rubber.

It was the turn of the control panel. In order to remove it, you need to unscrew two screws on the front of the panel and one on the right.

Next, you can proceed to dismantle the lower front panel. Pulling the latch lever, we separate the basement part of the facade - access to the drain filter and the hose for the emergency filter is open. The front panel can now be removed by unscrewing the eight fixing screws. The heating element and the drain pump open.

If during the repair process it is necessary to remove the tank and drum, then we advise you not to do this alone. Be sure to involve an assistant in this matter. Before removing the tank, you need to de-energize the heating element, disconnect all pipes, as well as the electrical wiring from the motor.

To do this, put the machine on its side, then remove the 4 screws on the bottom cover. The engine opens with a counterweight secured by shock absorbers. Disconnect the wiring from the connectors. It is important to remember what is being attached to what, therefore, before disassembling, it is advisable to photograph everything, in order to repeat everything exactly as in the picture.

But it remains to disconnect the drive belt from the engine. To do this, simply remove the belt from the pulley. Remember to put the drive belt on the small drive pulley first, then slide it over the large driven pulley and align to the center of the pulley when putting on the belt.

We present to you a diagram of the device, which will be very useful for repairs. The technical content of machines of different brands is about the same, and if you have already come across the replacement of spare parts for a washing machine, then it will be easier for you to cope with the next repair.

Now you can start a story about certain types of breakdowns and how to repair them.

The most common cause is insufficient water pressure. Then the machine stops, and in order to start it again, it must be turned off and then turned on again. If there is a lot of laundry loaded, for the machine to start, just turn it off and remove the excess.

If there is a break in the power cord or initially poor contact in the power button, then the device periodically turns off by itself. The machine may also stop if it is not level and slightly skewed.

To solve this problem, first check the water pressure in the water supply system, and also make sure that the valve supplying water to the machine is open well.

You should be aware that the free end of the drain hose connected from below must be located at a height of more than 2/3 of the height of the device, otherwise water will immediately pour out of the machine.

There are many reasons for this problem. Sometimes it is enough just to clean the powder container well - due to its clogging, water can simply flow out of it.

If, after checking these hoses, you are convinced that everything is in order with them, then the reason lies in the O-ring.

It is necessary to check the tightness of the seals, both in the door and in the connection of the filling hose. If they are worn out, they should be replaced. Then you need to check the drain pump and hose for foreign objects stuck there.

Therefore, the wash water is not heated. This is due to the failure of the heating element, but do not rush to change it - this may also be damage to the electrical wiring.

Therefore, you should carefully check the entire electrical circuit, as well as the contacts of the heating element itself, using a multimeter. If the tester shows the presence of voltage in the entire circuit, then this means that the heating element will still have to be replaced.

The place where the heater is installed should be thoroughly cleaned, only after that it will be possible to mount a new heating element.

The most common cause of noise is incorrect machine installation. Because of this, the unit produces a strong hum during spinning. For this, the position of the machine must be leveled using a spirit level.

But sometimes excessive noise can occur due to heavy wear on the bearings. It is impossible to fix them - only to change them. For an inexperienced repairman, this is a rather difficult task, because it may be necessary to saw and then glue the non-separable tank, behind which the bearing is located. Therefore, if you are not sure of your skill, then do not take up this business, it is better to call a qualified specialist.

But if the tank of your car can be disassembled, then this task can be within your power. To do this, you need to remove the tank, then disassemble it by unscrewing the bolts and disconnecting the fastening latches.

After the defective bearing has already been removed, you should thoroughly clean the shaft, check if it is worn out, and then just install a new bearing.

Finally, we present a short list of error codes that are most often issued by the unit.

E1 - system error when filling with water. Means that the required water level during filling is not reached within 20 minutes. Eliminated by turning off and then turning on the machine.

E2 - error when draining. Most often occurs when the drain filter is clogged.

E3 - too much water. You do not need to do anything, the water is automatically drained within 2 minutes.

E4 - too many things. Their mass does not correspond to the parameters of the machine. You need to extract the excess.

E5 - water heating does not work.

E6 - malfunction of the heating element.

E7 - malfunction of the water level sensor in the tank.

E8 - water heating does not match the selected wash program. Most often due to problems with the heating element.

E9 - water leakage or drain, recorded more than 4 times.

DE, DOOR - bad blocking. Most often - a badly closed hatch door.

We bring to your attention a good video that you need to watch before you start replacing the bearing yourself.

The process of dismantling and replacing bearings:

What the disassembly process looks like:

Before starting an independent repair, you always need to correctly assess your own strength and not take on overwhelming work. But repairing a washing machine yourself is not very difficult, it is enough to understand a little about mechanics, electrical engineering, and also have the necessary tools and materials at hand. You will succeed!

Household appliances from the manufacturing company Samsung are very popular in modern apartments and are recognized by housewives, due to their high quality, ease of use and durability. However, no matter how perfect the washing machine is, over time it may require service and repair. The most vulnerable point of any device is the movable assembly. In this article we will tell you how to replace a bearing in a Samsung washing machine, and what you need to carry out this procedure.