Washing machine zanussi do-it-yourself repair vertical

In detail: Zanussi washing machine DIY repair vertical from a real master for the site my.housecope.com.

People buy washing machines with top loading much less often than with front loading - this is a fact.

The tightness of the parts of the machine makes it difficult to disassemble
Increased vibration during spinning
On some machines it is not possible to level the rear feet
Corrosion of the top cover from moisture
Spontaneous opening of the drum flaps in case of imbalance

Narrow and deep, and fits perfectly into confined spaces in the bathtub, closets or kitchen
No need to bend over to load the laundry
Ability to interrupt the program and add laundry
Child safety. Control panel location.

Features and nuances for self-repair of vertical units:

The device contains the same elements (pressure switch, water intake valve, drum, tank, control board, pump, and so on).
The axis of the drum is structurally made on two bearings; a self-positioning sensor is sometimes located on the tank (fixing the drum with the flaps up).

We will show the dismantling of units using the example of Electrolux:

1.From the sides, using a screwdriver, release the control panel
2.Pull the plastic panel up and slide towards you
3. We tilt at a small angle towards ourselves to dismantle the wires from the board connectors
4. Take out the panel

To remove the electronic control module, disconnect the remaining wires and unscrew the screws shown in the figure.
For quick and correct assembly, take pictures of the connection points of the wire loops.

To remove the water inlet valve, disconnect the rubber hoses from the clamps and dismantle them.
Detach the wires and from the outside press on the holes to push out the valve.

To remove the side panels, unscrew a few screws, do not forget to save the washers for grounding the case.
Bend the wall from below with your hand and slide it down.

After removing the two side panels, access to the screws for dismantling the front panel appeared.

To remove the NTC sensors and self-positioning the DSP drum, it is enough to remove the right wall and dismantle them.

Frequent malfunction - there is no way to change the program .:

Example - Hotpoint Ariston ARTL 1047.

Many "craftsmen" sin that the control module is to blame for everything. But no!

It is enough to unscrew the two screws from the back and remove the control panel.

This very cracked handle is the culprit. Use the metal ring (the plug from the antenna for example).

By squeezing the plastic handle, the ring will prevent programs from skipping.

Blown up top of the Indesite vertical, Ariston:

Video (click to play).

001 - control knob 002 - white on-off / reset buttons 003 - white control panel 004 - bitron switch 005 - function keys 007 - display
008 - cover handle 010 - dispenser unlocking lever 011 - dispenser hook spring 012 - disengagement button dispenser 016 - cover support
018 - partition with shock absorber 021 - door interlock device 022 - white dispenser 023 - siphon cover 026 - control panel wiring 027 - 8-pos. potentiometer

There is an opinion that two drum supports instead of one are good.

This is not the case, and in the case of "vertical" it is just a forced engineering decision. The service life of the drum bearings does not increase for a minute.

If the screws are hard to loosen, heat them up with a blowtorch.

Use a special grease for oil seals - Litol-24, TsIATIM-221, SHRUS-4M, etc.

On "Kandy", in order to change bearings, you need to disassemble the whole machine to the screw! And what is the wild tightness in the depths of the "vertical". Sometimes you have to do everything literally by touch.

Automatic washing machines produced under the Zanussi brand have always been of high quality and low price. Nevertheless, due to long-term operation, through the fault of the consumer or due to a factory defect, the cars break down and they need repair. Repair of Zanussi washing machines should begin with studying their weak points, or rather, with the most common breakdowns, which we will deal with in this article.

As already noted, the repair of Zanussi washing machines should begin with typical breakdowns. Most of the models of such washing machines are quite demanding on the quality of water. AND The most common consumer mistake when buying and installing Zanussi equipment is its direct connection to the water supply. The water in the water supply system is far from the best quality and we are talking not only about hard water, often rusty water with all kinds of debris flows from the tap, which very quickly clogs the filters of the washing machine.

Important! Some craftsmen, when installing a Zanussi machine, specially remove the filter from the intake valve. This is absolutely impossible to do, because dirty water can literally destroy the machine from the inside.

Hence, the first typical reason for the failure of the Zanussi washing machine is clogged filters. In addition, these washing machines are equipped with extremely unsuccessful hatch locking devices. According to experts, this is one of the most common breakdowns. In this situation, both the mechanism itself and the sensor breaks down.

As in any other automatic "washing machine", the ten is broken in the Zanussi technique. Hard water should be considered one of the main reasons for such a breakdown, although some experts also talk about unsuitable materials from which the heating element tube is made. They say that this metal attracts scale even more. And finally, the last weak point of Zanussi washing machines is the drive belt. It is recommended to check the belt at least once every 4 years and, if necessary, tighten or replace it.

Periodically, all the filters of the washing machine need to be cleaned, if this is not done for some time, then you may encounter a problem. If there is a blockage in one of the filters of the washing machine, the household appliance either does not have the ability to collect water for washing, or does not drain it. Specifically, in Zanussi washing machines, the first option is more common. What can be done?

Unscrew the inlet filter located on the water pipe and clean it.
If the inlet filter was not installed, it means that a blockage has formed on the inlet valve filter (in the place where the inlet hose connects to the machine). Remove the top cover of the washing machine and unscrew the inlet valve and filter.
We unscrew the filter and thoroughly rinse its cuff and mesh from dirt, then twist the filter with the inlet valve and put it in place, then close the top cover of the machine.

The "delicate" inlet filters of the Zanussi washing machine create many problems, but they protect the internal units from damage due to the ingress and accumulation of foreign objects and debris brought along with the water. Experts recommend installing an inlet filter with a water softener cassette directly on the water pipe.

Dirt in the washing machine can not only accumulate from tap water, but also from clothes. With clothes, not only sand and pieces of dirt get into the car. The peel from seeds, coins, hairpins, buttons settles in the drain filter. All this at one moment can stop the work of the machine. Experts recommend every time after 2-3 washes to clean the drain filter with your own hands, preventing it from getting littered.

Note! Before washing, be sure to check the pockets of items that you put in the drum of the Zanussi, foreign objects can damage the internal parts of the "home assistant".

The device that locks the hatch of the Zanussi washing machine may break due to careless handling by the user, factory defect, or due to wear. The main problem arises with the counterpart of the device. Its plastic part that holds the plates is rather "flimsy" and breaks if you close the hatch very abruptly and forcefully. In this case, the hook-to-eye remains intact, since it is made of metal, and the blocking device breaks, making washing impossible. How to fix a breakdown with your own hands?

In this case, it is almost impossible to repair the device blocking the hatch, you will have to change it. Its average cost is about $ 30. It is quite expensive to purchase such spare parts for future use, so you first need to remove the old device in order to be 100% sure of its malfunction, and only then “go shopping”. How do I remove an old device?

We open the hatch cover wide open.
To the right of the hatch there is a hole for a locking hook and two screws holding the hatch locking device, they must be unscrewed.
Next, we pry on and remove the clamp that holds the hatch cuff (a large elastic band located around the hatch of the washing machine). It is most convenient to pry the clamp with a screwdriver, because it is quite thin and fits snugly, you cannot pick it up with your fingers.
After removing the clamp, we take out the cuff itself. You need to pull it out with your fingers.
We put our hand between the front wall of the washing machine and the edge of the drum and take out the locking device.
We examine it visually, make sure that the plastic part is broken, and the plates have popped out, we get together and go to the store with the old device.
We show it to the seller, buy the same new one, come home, and install it in place of the old one. Problem solved!

Note! "Hit" each time for $ 30. this is an overhead, so treat your Zanussi washing machine as carefully as possible. It is better to close the hatch carefully, and then press down on its edge until it clicks, this way a gentle and safe fixation of the hatch cover is achieved.

Teng is the weak point of all washing machines that have to work in conditions of using water with a high content of mineral salts. Some companies are trying to protect the heating elements of their cars with special polymer coatings. For example, the Samsung company five years ago announced heating elements with a polymer coating, which supposedly repels scale. Their idea failed miserably, because scale on their heating elements formed in the same way as on others, without coating.

If the heating element of the washing machine breaks down, then the water in the tank stops heating up, and the system may give an error E05. In washing machines The Zanussi Teng is located at the back of the tank, so you will need to remove the rear wall to get to it. We need to first check the heating element for operability, if it does not work, then it must be removed and a new unit installed. How it's done?

We unscrew the bolts holding the back wall of the washing machine body, remove it.
In the lower part, two contacts will stick out directly from the tank, from which the wires go - this is the ten.
Take a multimeter and check the resistance of the heating element, if the device shows zero, you will have to change the heating element.
There is a nut between the contacts of the heating element, it must be unscrewed.
We remove the wires from the heating element.
Carefully remove the old heating element from the groove. It may be difficult to do this, as he got used to it over time.
Sprinkle WD-40 grease on the right and left of the contacts in the slots and pull out the old ten in a swinging motion.
Remove any limescale and dirt that you can reach through the hole, and do not forget to wipe the edges of the hole with a clean cloth.
Carefully insert and screw on the new heating element and connect the wires to it.
We put the back wall in place and check the operation of the washing machine.

Important! Buy only original heating elements made specifically for the required model of the Zanussi washing machine. There is a risk that an unsuitable heating element will burn out, "taking" the control unit with it, and repairs will become even more expensive.

"Symptoms" of drive belt problems are the motor running, not the drum spinning. In this case, washing, as you understand, is impossible. The hum of the engine cannot be confused with anything, but you should not make it idle again. What should be done if there is a problem with the drive belt?

First, inspect the location of the malfunction by removing the back wall of the washing machine.
In the niche that opens, we will see a large round drum pulley, on which the belt is put on, and below there is a small engine pulley, on which the drive belt is also put on.
If the belt is in place, but does not rotate the drum pulley, it means that it has exhausted its resource and needs to be changed. If the belt comes off, you just need to put it back in place.
We put the belt on the pulleys, put the back wall in place and check the performance of the washing machine.

Summing up, we note that the Zanussi washing machine, despite its reliability, has several typical malfunctions that consumers encounter most often. These are clogged filters, a broken hatch blocking device, a burned out heating element and a drive belt that has worked out its life. If you have a washing machine of this brand, you should have an idea of how to troubleshoot the listed malfunctions.

The Zanussi washing machine is a product of an Italian brand. Consumers appreciate the CM of this brand for the combination of high quality and affordable cost. During operation, breakdowns occur - due to wear, factory defect or violation of operating conditions. Let's figure out in what situations it is possible to repair the Zanussi washing machine with our own hands.

After examining the statistics from service centers that repair Zanussi washing machines, we can single out several typical problems for this brand:

Water quality related. Tap water in Russia is characterized by increased hardness. And there are problems with cleanliness - because of old pipes. As a result of heating the water to 90–95 degrees, a precipitate is formed - scale. Due to sediment, a tubular electric heater (TEN) gives off heat poorly, overheats. Particles of dirt and rust contained in the water clog the filters - the water intake and drainage system suffers.
UBL (sunroof locking device). This unit breaks more often due to the fault of the manufacturer. There are obvious flaws here - the UBL and the sensor in the Zanussi CM fail more often than in the devices of competing brands.
Heating element. Burns out due to scale build-up. In addition, it has a limited service life and can burn out after 3-5 years of intensive use. But experts also assure: in the heating elements of this brand, the components from which the tubular part is made are unsuccessfully selected.
Drive belt. This element cannot boast of reliability. It is recommended to check the belt for integrity and tension once every three months. If there are stretch marks (damage), it will have to be tightened or changed.

The modern Zanussi automatic washing machine is equipped with a self-diagnosis function. Fault codes signal a breakdown, but do not always allow you to understand its cause - you need to figure it out. The display shows error codes that need to be deciphered, and then decide what to do next. In difficult situations - contact the service. Below are a few common codes.

Weak pressure in the pipes.
The filter mesh of the inlet valve is clogged. Check the inlet hose for integrity, clean the mesh.It is recommended to check the resistance of the valve coil

In the instructions, you can find a complete table for decoding the codes - there are dozens of them, we have given only a few in order to clearly explain how the self-diagnosis system works.

Malfunctions and repairs of Zanussi washing machines are the sphere of interest of service centers. But not all breakdowns are so critical as to immediately contact a specialist. If the device is no longer under warranty, it makes sense to find out the cause of the problem and if its elimination is reduced to replacing the worn part, then you can make the repair yourself.

If you have a front-facing washing machine, read the instructions - it contains the device and diagram of a Zanussi washing machine with horizontal loading. In CM with vertical loading, despite the differences in design, filters are cleaned in the same way. Moreover, this must be done regularly, without waiting for clogging - then there will be no problem. If one of the filter elements becomes clogged, the machine will not be able to collect or drain water. In Zanussi, the filler filter is more likely to be clogged. Procedure:

Unscrewing the inlet filter from the water pipe.
If the above-mentioned protection against dirty water has not been installed, then proceed to cleaning the filter of the inlet valve. Its location is where the bay hose is connected to the CM.
Remove the top panel of the washer. Unscrew the valve together with the filter.
Having untwisted the dismantled unit, they begin to rinse the filter mesh. Do this under running water.
Reinstall the node.

Intake filters are often problematic as they become clogged with foreign particles. But the filters protect the device from damage that can be provoked by solid fractions in the water. If you do not have a filter element at the inlet, then be sure to install it - it is mounted directly on the water pipe.

Please note that dirt collected in filters is also due to dirt washed off from clothing and other items. Particles of sand and dirt get into the apparatus and clog the systems. But even more dangerous are solid objects that have fallen out of pockets during washing - they can damage the drum and other parts of the SM. It is recommended to clean the filter frequently - every 2-3 washes.

The drain filter is located in the lower front of the CM, its cleaning is the same for all brands and models of machines, and it is described in a separate publication.

Failure of the UBL is not rare - it is often found in the Zanussi Aquacycle and Zanussi Easyiron models. The malfunction can be caused by a factory negligence or a failure in the control board. In the second case, the blocker is not even to blame for the problem.

UBL has plastic components - they are unreliable and can break. It happens that a strong pop of the door is enough. The blocker is usually not repaired - it is much more expedient to install a new one. The cost of UBL for Zanussi devices is 1,500 rubles. Not cheap. Therefore, before buying a new element, remove the old one - you need to make sure it is defective. The procedure for replacing the blocker:

Open the hatch door wide.
Look to the right of the hatch - there are screws (2 pieces) that hold the UBL. Unscrew the screws.
Pry up and remove the clamp that holds the cuff. The collar is a large rubber seal located around the perimeter of the hatch. Pry the clamp with a screwdriver and remove it.
When the clamp is removed, you can remove the cuff, pull it out with your hands, without helping yourself with tools - so as not to damage the rubber.
Put your hand into the space between the front panel and the drum and remove the bollard.
After examining the blocker, make a decision. If there is damage to the plastic body or other violations of the original design, you need to buy a spare part.

Take the broken blocker to the store - let them pick up an analogue there. Returning with a new spare part, put it in the vacant space.

Important! Whenever you feel like slamming the door - remember how much the locker costs.

Heating element is the most vulnerable part of any washer operating in hard water conditions. You have a budget model, for example, ZWSG 7101 V or an expensive one, like ZWI 71201 WA - heating elements suffer the same way. A number of manufacturers protect electric heaters with special polymer coatings. So, Samsung tried to create and implement heating elements with a protective polymer layer that repels scale. However, nothing good came of it.

It is easy to guess about the breakdown of the heater by the lack of water heating. An error code appears - E 61, U 62, E 66, E 69. In the brand under consideration, the heaters are located in the back of the device - this arrangement allows you to quickly get to them. It is enough to dismantle the rear panel.

Before buying a new heating element, make sure of the final malfunction of the old one. Procedure:

Unscrew the screws to remove the back panel.
Look down - there is a heater under the tank, contacts with wires stick out from it.

Measure the resistance with a multimeter. If it is zero, go buy a new heating element for the Zanussi washing machine. Working resistance - 20-40 ohms.

Unscrew the nut located between the contacts and disconnect the wires.
Remove the element from the seat. It might have to make an effort - he might have stuck.
Sprinkle special WD-40 grease into the grooves near the contacts, and then, wobbling the heater, pull it out.
Using the vacated hole, try to remove dirt and sediment.
Supply a new part and connect the wires.

Fasten the back panel with screws.

Important! Take only an original spare part. Chinese counterparts can cause damage to the electronic module, and then expensive repairs are inevitable.

You can recognize them by the lack of rotation - the motor is running, but the drum is not spinning. When such a "symptom" appears, turn off the machine - there is no need to run the electric motor idle. Further procedure:

After dismantling the back wall, inspect the problem area.
You will see a pulley - a large circle on which the belt is worn. Look down - there is a small motor pulley, which is also wearing a belt - this is a belt drive.

When the belt is in place, but the pulley does not rotate, the conclusion is one: it's time to go for a new belt. But if he jumped off, the solution is easier - put it on the pulleys.
Put the wall back and check the operation of the device.

Despite their good reputation, Zanussi CMAs are not perfect. They sometimes break, and they have several weak points. If you purchased a device of this brand, it is useful to have an idea of \ u200b \ u200bthe diagnosis and elimination of the most common breakdowns.

Do you like automatic washing - love to fix the machine too! This is how any owner of a washing machine could paraphrase the well-known proverb.

Units of the Zanussi brand are no exception. Although there is no reason to complain about the quality of these machines, they sometimes give an unpleasant surprise. So, Zanussi is a washing machine: do-it-yourself malfunctions and repairs.

But such malfunctions occur relatively rarely. In most cases, the failures of Zanussi machines are due to very commonplace reasons, which the owner himself can cope with.

We list the weak points of these units:

Dependence on water quality: this feature, I must say, is typical for all washing machines. The hardness salts present in the water at high temperatures are intensively deposited on the heating element in the form of scale, and dirt and rust clog the filters, as a result of which the collection of fresh water and the removal of waste water slows down or completely stops.
Poorly thought-out design of the locking device on the hatch: in Zanussi cars, this mechanism, as well as its sensor, are clearly incomplete and fail very often.
TEN: some experts believe that the heater in these machines is particularly susceptible to lime scale formation due to poor choice of tube material.
Drive belt: another relatively unreliable element. Zanussi owners should check the condition of the belt at least once every 4 years, carrying out a tightening or replacement if necessary.

Now let's look at the typical symptoms that manifest themselves in certain malfunctions.

If at the same time it is clearly audible that the engine is running, then the matter is most likely in the drive belt. To inspect it, you need to remove the back panel of the machine body by unscrewing the screws that fix it.

Next, we act according to the situation:

If the belt has slipped off one of the pulleys, it must be reinstalled.
If there is a break in the belt, you need to purchase and install a new one.
If the belt is intact and in place, but does not transmit rotation due to slippage, then it has exhausted its resource and must also be replaced.

If, during inspection, you find that the electric motor pulley does not rotate, then there is a more serious breakdown and you need to contact the service center.

If the bollard is jammed, the hatch can be opened using the emergency cable by pulling it towards you. You can find it behind the bottom panel (you need to unscrew it), to the right, near the filter. The cause of the malfunction lies in the electronics, so you will have to contact a workshop.

The latches that hold the hatch closed are made of fragile plastic, so they often break.

To make sure that this is exactly the case, the lock must be disassembled:

after opening the hatch, unscrew the two screws with which the lock is screwed to the body;
remove the hatch seal (cuff), having previously removed the clamp holding it (you need to pry it off with a screwdriver);
after removing the cuff, the lock can be pulled out.

If the plastic parts of the mechanism are indeed broken, a new lock must be purchased and reinstalled.

To make the lock last longer, close the hatch as gently as possible.

The situation when, simultaneously with the collection of water, it is discharged through the drain hose (before the drum begins to rotate) may be due to the low location of this hose. Its free end should be raised by 50 - 70 cm.

Self-draining will also take place if the drain pipe is damaged, only in this case the water will flow not from the hose, but from under the machine.

More serious reasons are faults in the control module or level sensor that mistakenly turn on the drain pump.

We are looking for the cause of the malfunction:

First you need to make sure that the water is not turned off.
Next, you need to check the throughput of the filling hose by disconnecting it from the machine and turning on the water supply.
If the water flows through the hose properly, put it back in place and check the condition of the filter. Together with the priming valve, it is located where the hose enters the unit housing. After removing the top cover, the assembly (valve + filter) must be unscrewed, after which the filter can be disassembled and cleaned.

Cleaning the filters, both inlet and outlet, must be performed regularly, without waiting for problems.

If the water supply has not resumed, it is necessary to check the operation of the priming valve. The resistance of its winding should be 3.75 kOhm, and when the voltage indicated on the case is applied to the contacts, the device should open. The defective valve must be replaced.

This problem can also signal a breakdown of the level sensor or clogging of its tube.

In many cases, the owner of the washing machine can repair it themselves. Do-it-yourself Bosch washing machine repair - an overview of the main types of breakdowns and methods for their elimination.

What criteria should be considered when choosing a shower stall, read in this topic.

Breakdown of the heating element, wear of the bearing, failure of the control unit - these types of malfunctions in washing machines are the most common.Here https://my.housecope.com/wp-content/uploads/ext/740/cancliz/mnogokvartirnyie-doma/santehnika/stiralnaya-mashina-indezit-neispravnosti-remont-svoimi-rukami.html you will learn how to fix it yourself breakdowns of cars Indesit.

The first step in such a situation is to check the serviceability of the engine and the integrity of the power supply circuit.

It will be difficult to do this without sufficient experience, so it is better to contact the service center.

Here, if necessary, they will check the correct operation of the control module circuit - perhaps it is it giving the device incorrect commands.

Most often, the cause of such failures is the breakdown of the heating element - due to natural wear and tear or due to fouling with scale. Follow these steps:

After unscrewing the fasteners, remove the back panel of the case.
Check the resistance of the heating element with a multimeter (its shank with the wires connected to it protrudes from the tank in its lower part). At room temperature, the meter should read 30 ohms.
If the resistance is different from normal, the heating element must be replaced. The wires are disconnected from it, and then the nut located between the contacts is unscrewed. The heater can then be pulled out. This should be done with care, gently rocking the element and not applying excessive force. If the heating element is stuck and does not give in, you need to soften the scale with WD-40 liquid. After dismantling the heater, its seat must be cleaned, after which it will be possible to install a replacement. The new heating element must correspond to the given model of the washing machine. Heating element from another model can burn out, moreover, together with the control module.
If the resistance measurement showed that the heating element is working properly, you need to check the condition of the temperature sensor. Its performance is also verified by measuring the resistance. At room temperature, it should be 5.7 - 6.3 kΩ.

Read also: DIY cooler repair

The reason may lie in the "sticking" of the contacts of the heating element relay located near the control module.

If water is found under the washing machine, the following items should be checked:

Gasket at the connection of the filling hose. If excessive wear occurs, it must be replaced.
Hatch seal. Over time, this element can deform or crack. To dismantle a worn cuff, it is necessary to remove the clamp holding it. It fits snugly enough, but if you pry it off with a screwdriver, it comes off quite easily.
Drain connection or where the drain hose is attached to the pump. If there is damage in this area, water will start to seep out at the same time as filling the machine. A damaged part - hose, pipe or pump - must be replaced.
Tank of the car. Leaks can be caused by its depressurization.

In the latter case, you will need specialized equipment for repairs, so you will have to contact the service center.

The machine itself informs the user of some breakdowns by displaying a special alphanumeric sequence on the display - an error code. Here are some of them:

E11 - insufficient water supply during washing. As already mentioned, you need to check the water inlet path, filter and valve.
E13 - there is a water leak into the sump.
E21 - problems with water drainage. Most likely, you need to clean the drain filter. Together with clothes, sand, seed husks and other small debris, buttons, pins and other small objects can get into the machine, therefore it is recommended to clean the drain filter after every 3 washes. If this measure did not give a positive result, it is necessary to check the operation of the pump. Its winding resistance should be approximately 170 ohms.
Codes E23 and E24 speak of a malfunction of the drain pump control semiconductor in the control module.
E35 - the water level in the tank has exceeded the permissible threshold. Most likely, the reason is a breakdown of the level sensor or a clogged tube.
E41 - E45 means a malfunction of the hatch lock or its blocking elements.

A washing machine breakdown is not such a rarity. Some brands of units have their own weak points. Washing machine Kandy - DIY repair of basic faults, read on.

We will analyze the types of mixer taps and the features of their device in this material.

Loud noise when the drum rotates at high rpm may be due to the following reasons:

The position of the machine is not strictly horizontal.
The drum is underloaded, as a result of which the center of gravity of the laundry has deviated from the center of rotation (strong vibrations will occur at high speeds).
One of the bearings is broken.

Bearings in Zanussi machines can be replaced by yourself. This is done like this:

Having completely disassembled the machine, you need to remove the tank with the drum.
After removing the drum pulley and unscrewing a few bolts around the perimeter of the tank, the latter must be disassembled into two parts.
With careful hammer blows through a wooden lining, you need to knock the drum half shaft out of the bearing assembly in the rear half of the tank.
Next, using a puller, the bearing itself should be removed along with the oil seal.
The drum axle shaft and bearing seat must be thoroughly cleaned.
In place of the old bearing, a new one is installed, while its oil seal is stuffed with special grease.

Having lubricated the axle shaft and the inner ring of the bearing, the drum and the rear of the tank are again assembled into a single unit, after which both halves of the tank are fastened, having smeared the junction with a sealant.

In some models of Zanussi washing machines, the bearing assembly - the so-called caliper - is unscrewed.

After removing the drive belt, you need to dismantle the drum pulley (it is held by a screw). Next, you need to disconnect the grounding plate and unscrew the caliper by turning it to the right.

The caliper on the side opposite to the pulley (in machines with top loading) is unscrewed in the opposite direction. The direction of rotation at each node is indicated by arrows labeled “Open” and “Close”. After installing a new caliper, the unit is assembled in the reverse order.

To keep the screw holding the pulley securely, the threads should be coated with Loctite before screwing in.

Repair of washing machines Zanussi (Zanussi) is a frequent occurrence. Despite the fact that these cars come off the assembly line under the sign of a foreign brand, they can also break. And often the manufacturer is not at all involved in the fact that the machine broke down too early.

External factors and improper operation are the most likely reasons for the failure of the SM.

Using the statistics of service centers, you can quickly understand which nodes and parts in the device of the Zanussi washing machine are the most vulnerable

The dependence of parts on water quality. By the way, this is typical not only for the Zanussi brand, but also for other machines. Water oversaturated with salts with strong heating is deposited with scale on the heater and other elements.
The purity of the water in our water supply systems also does not differ, so the filter systems of the machine can become clogged with dirt and rust over time. As a result, the typesetting and drainage system suffers.
Hatch lock. This is already the fault of the manufacturers: both the blocker and the sensor are slightly underdeveloped, therefore they break more often than other brands of SMA.
The heater (heating element) quickly builds up with scale. Experts believe that this is also due to the fact that manufacturers miscalculated in the selection of components from which the tubular part of the heater is made.
Drive belt. It does not differ in reliability, so every 3 months it does not hurt to check its tension and integrity. If you see signs of stretching or damage to the belt, a tightening or replacement of the knot is required.

The only good thing is that it is possible to determine the malfunction on time, since the “smart” automatic washing machine Zanussi notifies the user of problems using the trouble codes.

Usually a Zanussi washing machine gives out the following error codes: E11, E12, E21, E22. Let's consider the most common combinations.

Water does not leave the system - cleaning of the drain filter and checking the nozzles for blockages is required.

It is also necessary to check the performance of the pump impeller - it should rotate freely in both directions. If the stroke is difficult, the pump needs to be replaced.

Complex breakdowns should be entrusted to a professional, but easy repairs to Zanussi washing machines can be easily done by yourself.

Next, we will look at how to repair a Zanussi washing machine with your own hands.

All filtration systems need to be cleaned periodically. If you neglect this rule, then later problems cannot be avoided. If there is a blockage in any of the filters, then there are problems with the intake or drainage of water.

In SM Zanussi, it is the filler filter that is most often clogged. What to do to normalize the work of the typewriter?

Just unscrew the inlet filter - it is located on the water pipe.
If you have not installed such a filter, then you need to clean the filter mesh.

Attention! Experts advise placing the inlet filter on a pipe with a special filter cassette that softens the water.

To clean the filter mesh, proceed as follows:

Find the junction of the water intake hose with the washer body.
Remove the top cover of the CM to unscrew the valve and filter.
Disassemble the filter and rinse it under the tap.
Replace the filter.
Reassemble everything in reverse order.

Important! The device of the Zanussi horizontal loading washing machine is different from the front design, but the filter is cleaned in the same way.

By the way, pollution can accumulate not only because of the "errors" of the water supply system, but also because of the clothes that you send to the drum. From too dirty things, sand, dirt, debris, threads penetrate into the machine systems.

Craftsmen often find small coins, seeds, hairpins, crumpled checks in the drain filter. All this "nonsense" can provoke a stop in the work of the AGR.

Important! Remember to clean the filter at least every 3 months.

The problem with the UBL is a frequent malfunction of the Zanussi Aquacycle CM, but it also occurs in other models: for example, the Zanussi Easyiron.

It is difficult to tell right away why the blocker breaks down - through the fault of the manufacturer or user negligence. But there may be problems with the control board - then the blocker has nothing to do with it.

The plastic components of the sunroof locking device are unreliable and can break even if you simply slam the hatch shut with force. In this case, the metal hook will survive, but due to the breakdown of the UBL, washing will still be impossible.

The blocker is usually not repaired - it is easier to replace it with a new one. For Zanussi UBL typewriters costs about 1,500 rubles. It's a little expensive, of course, so first you should remove the old blocker to make sure it is 100% broken.

Remove the device according to the following scheme:

Open the door.
On the right you will see a small hole for the locking hook, and next to it there are two screws that hold the UBL. Unscrew the fasteners.
Remove the gasket (lip). It is held in place by a wire tie that runs in a circle along the entire elastic. Pick it up with a thin screwdriver and remove. Then remove the cuff - do it by hand, without tools, so as not to damage the delicate elastic band.
Remove the blocker by disconnecting the wires.
Carry out a visual inspection of the device and make sure that the plastic part is intact. If the plastic is broken, and the records popped out, take the device with you and go for a new one.
Show UBL in the store to sell you exactly the same.
Install the bollard in reverse order.

Important! Close the door gently until it clicks, pressing down on the edge to extend the life of the device.

As we said above, the heating element is one of the most vulnerable places of any washing machine, especially Zanussi. The washing machine with such a breakdown may give an error E05, while the water in the tank stops heating.

To make repairs yourself, you will have to disassemble the SM case a little:

Turn the machine with the front wall towards you.
Unscrew the screws from the panel to remove it.
From the bottom of the tank you will see the heater shank - it has 2 contacts and wires coming from them.
Measure the resistance with a tester. If the device shows a value close to zero, the heating element will have to be changed. The readings of a working heater will be 20-40 ohms.
To remove the heating element, unscrew the nut located in the center of the shank.
Disconnect the wiring to the heater.
Make an effort to get the heating element out of the groove. If there is a lot of plaque on it, then it could get stuck. Take WD-40 grease and lightly spray on the crevices. Loosen the old heating element and pull it towards you.
Clean the hole well.
Install a new heater, connect the wiring.
Reattach the back panel and run a test wash. If the water heats up, and the E05 code is gone, then you did everything right.

Important! When choosing heating elements for the Zanussi washing machine, buy only original parts. Don't go for cheap Chinese counterparts - they won't last you long. An unsuitable heating element can also provoke a breakdown of the control unit, and then the repair will definitely "fly into a penny."

Damage caused by the drive belt is accompanied by the fact that the motor in the washing machine does not stop working, but the drum does not rotate. To check the integrity and location of the belt, proceed as follows:

Remove the back cover by unscrewing the fasteners.
In the niche you will see the drum pulley on which the belt should be put on. The motor pulley is much smaller and must also have a belt on it.
Correct the belt if it has shifted.
If the drum does not rotate and the belt is in place, then a replacement is needed.
After adjusting or installing a new belt, refit the panel and run a test wash.

As you can see, the repair of Zanussi washing machines consists in eliminating typical failures and breakdowns. Fortunately, these malfunctions are such that you can easily eliminate them without the help of a wizard.

We only advise you not to touch the electronics. Even if you have a Zanussi washing machine circuit, in order to repair or replace an electronic module, you need special tools and relevant knowledge and experience. Do not want to provoke additional breakdowns - trust the master for complex problems.

This video may help you:

Video (click to play).